Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Eagle Mountain
Gate hinge replacement, post reset, and on-site welding in Eagle Mountain typically runs $180-$640 depending on the post condition and whether we’re cutting out old steel or anchoring fresh footings. Most jobs off Peden Road, Boat Club Road, or the cove-side streets in 76179 are done in a single visit because we weld in your driveway, not back at a shop. If your gate is dragging, racked off plumb, or the operator is fighting a sagging hinge, call (877) 610-2993 and you’ll get a live person who knows Eagle Mountain’s clay soil problem better than most.
Hal Gatewood has been fixing gates since 2001. The kind of gate work this lake community needs is not a parts-swap job. It’s a footing-and-alignment job, and that’s where we spend most of our time in 76179.
Why Gatewood Fence & Gate Is Eagle Mountain’s Preferred Gate Parts & Welding Company
Eagle Mountain is different from most of the DFW service area. You don’t have rows of quarter-acre lots with the same creaky ornamental gate. You have multi-acre properties off Ten Mile Bridge Road, long lake-view driveways, and older ranch entrances out toward the rural fringe where a gate might be forty feet of pipe on a caliche pad. We’ve done enough post work in this specific soil to know what we’re going to find before we dig: clay that heaves, posts that drift, and hinges that rack out of line. That local pattern shapes every quote we write for Gate Parts & Welding in this area.
Calls from Eagle Mountain are answered by a live person, 24 hours a day. Not a queue. Not a chatbot. You’ll get someone who can tell you whether the problem sounds like a post issue, an operator issue, or a weld fatigue issue before we ever roll a truck. Every job carries our 90-Day Done Right Promise in writing. If it’s not done right, Hal comes back and makes it right. That promise is stamped on the invoice, not buried in fine print. Our company is locally owned and owner-operated since 2001, with Hal Gatewood’s name on the shop and on every invoice. The person who shows up is accountable to you and to the name on the truck.
Our Gate Parts & Welding Services in Eagle Mountain
Hinge Replacement
A gate sags in the hinge post, not in the middle, and that is where we start. In Eagle Mountain, hinge replacement almost always means more than swapping a barrel hinge. The expansive clay under 76179 footings swells and shrinks with every wet-dry cycle, and that movement transfers straight into the hinge post. We cut off the old hinge, inspect the post plumb, and weld the new hinge to true alignment. On ornamental iron gates along the lake side, we match the weld profile so the repair doesn’t look like a patch job.
Post Replacement
Post replacement out here is the dominant repair call for a reason. Caliche-topped pads over shifting clay subgrade pass inspection at build-out and then drift two to three inches out of plumb within two or three seasons. We dig the old footing, re-set the post in properly compacted backfill with concrete footings sized for the gate weight and span, and weld the gate back to a post that actually holds vertical. On long driveway posts off Morris Dido Newark Road, we use deeper footings because the sustained wind off Eagle Mountain Lake pushes a wide gate like a sail.
Rail Repair
Rail failures on swing and slide gates in Eagle Mountain usually show up at the weld joints first. The constant lake wind flexes the rail, and the clay movement racks the frame until a weld cracks. We cut out the cracked section, fishplate or sleeve it depending on the pipe gauge, and weld it back square. On older ranch pipe gates, we work with the existing steel rather than insisting on a whole new frame. Fix the panel without the post and you’ll fix it twice, but fix the post and rail together and the gate runs true for years.
Custom Welding
Some gates can’t be fixed with a replacement part because the part doesn’t exist. Custom-coded ornamental gates, gates that builders modified on site, or ranch entrances that were never from a catalog at all. We weld on site, so the gate stays in your driveway and Hal’s crew fabricates whatever bracket, hinge plate, reinforcement gusset, or operator mount the job calls for. In Eagle Mountain, we’ve built and welded operator plates onto gates that were never designed for automation, which is common on older acreage properties where the electric gate was an afterthought decades after the original fence.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Eagle Mountain
We’re certified to service Nine major gate brands, and around Eagle Mountain we see a lot of Linear, Viking, and Ghost Controls operators on residential solar setups, plus DoorKing on the larger slide gates out toward the rural edge. We stock common boards, arms, photocells, and battery kits for those brands so we’re not ordering parts and making you wait a week while your gate is stuck open. If you have an operator acting up and you’re not sure which brand it is, call us and read the label on the motor box. We’ll tell you over the phone whether it’s worth repairing or whether the board has failed.
Common Gate Parts & Welding Problems We See in Eagle Mountain Homes
- Hinge posts racked out of plumb by clay movement. The black gumbo soil in 76179 expands when wet and shrinks when dry, and posts move with it. A swing gate that scraped the ground in August may bind on the operator by March. This is the number one call we run in Eagle Mountain.
- Weld fatigue at the post connection on lake-facing gates. Sustained wind off Eagle Mountain Lake constantly loads the gate panel. Over time, the repeated flex cracks welds where the hinge plate meets the post or where the rail meets the stile. We see this on cove-side properties and long open driveways more than anywhere else in the county.
- Solar openers on acreage entrances that run weak in the morning. Long driveway gates without mains power rely on solar panels and batteries. Undersized panels or old batteries can’t hold enough charge for a heavy farm gate after multiple cycles. We size panels and battery banks to the actual gate weight and daily cycle count out here.
- Operators fighting misaligned photocells after post movement. When a post shifts, the safety eyes go out of line and the opener refuses to close, or it reverses mid-cycle. We re-align the photocells AND fix the post. Adjusting the photocell without fixing the post means you’ll be out there bypassing the sensor every time it rains.
Pricing for Gate Parts & Welding in Eagle Mountain, TX
In Eagle Mountain, hinge replacement on a residential swing gate typically runs $180-$340 depending on the hinge style and whether the post needs welding repairs. Post replacement with new concrete footing runs $350-$640 for most driveway gates on standard residential lots, and higher for wide farm gates or gates with operators that have to be removed and reinstalled. Rail repair runs $150-$400 depending on the crack location and whether we’re fishplating or replacing a full rail section. Custom welding is billed the same way, by the job, not by some vague “welding fee.” You’ll get a written price before any work starts, agreed to up front, and that price doesn’t change at the door. We also offer $40 off any repair over $200, no trip charge inside the county, a free second opinion on any written estimate, and a permanent 10% discount for seniors and veterans. Call (877) 610-2993 for an exact quote. Estimates are free.
We Also Serve Cities Near Eagle Mountain
Our gate parts and welding work covers more than just the lake side. We regularly run calls in Saginaw, Azle, Briar, and River Oaks, and the same local soil knowledge applies from the clay lots near Saginaw to the older ranch entrances outside Azle. If you’re near Eagle Mountain but not inside 76179, call anyway. We’ll tell you over the phone whether we cover your road.
Serving Eagle Mountain, TX - Our Local Coverage Area
We’re based in the Eagle Mountain area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Eagle Mountain
Because the post is moving under the hinge, not because the hinge is wearing out. The expansive black clay in 76179 heaves and contracts with moisture swings. Posts set into that clay drift off plumb, and once the post leans even a degree or two, the hinge carries the entire gate at a bad angle and sags worse every season. We fix the post first, then the hinge. Call (877) 610-2993 and we’ll tell you what you’re actually looking at.
Sometimes, yes, if the post is still plumb and solid. We’ll check the post with a level and assess the footing before we ever weld anything. If the post is moving, welding a new hinge onto it just moves the sag point. On pipe gates out toward the rural fringe, we can often cut and weld a new hinge in place same-day. Call us with the gate width and post size and we’ll quote it honestly.
No, it’s a sign the battery isn’t holding charge or the panel is undersized for the gate weight. Morning is the worst time for solar systems because the battery has been through a night of standby draw and hasn’t gotten enough sun yet. On heavy acreage gates in Eagle Mountain, a panel that works on a small residential gate may be completely inadequate. We size the panel and battery bank to your actual gate and daily cycle count, and we stock replacement batteries for linear, Viking, and Ghost Controls systems. Call (877) 610-2993 for a site assessment.
UL 325 requires automatic gates to have monitored entrapment protection, which usually means photocells or contact edges that detect an obstruction and reverse the gate. When your post shifts out of plumb, your photocells go out of alignment and the system fails its safety check, so the gate stops closing. Fixing the post is part of getting your gate back to code compliance. We test every safety edge and photocell after any post or hinge work on an automatic gate.
In most cases, yes. We install and service DoorKing and Linear slide operators on older pipe gates regularly. The gate needs to roll freely and the track needs to be level. If the gate has been welded and patched over the years, we may need to do some rail work first so the operator isn’t fighting the gate’s own weight. We’ll tell you upfront what’s needed before we order any equipment. Call (877) 610-2993 to get a straight answer.
Call Gatewood Fence & Gate for Gate Parts & Welding in Eagle Mountain
If your gate is sagging off its hinges, binding on the operator, or cracking at the welds, call us before you spend money on a replacement gate that you probably don’t need. We weld on site, we quote before we start, and every job carries the 90-Day Done Right Promise in writing. Gate Parts & Welding in Eagle Mountain is what we do, and we do it here, on your driveway, with Hal Gatewood’s name on the truck. Call (877) 610-2993 for a free estimate.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Eagle Mountain since 2001.