Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Conyers
If you’re searching for Gate Installation - Conyers or gate parts and welding, you’re likely looking at a gate that won’t swing, a post leaning out of plumb, or a weld that finally let go after twenty years of Georgia weather. We handle all of it, from hinge replacement on 1990s ornamental iron driveway gates to full post resets on farm entrances south of SR-138. Our crew works Conyers every week, and we stock the heavy-gauge hardware this red clay market actually needs. Call (877) 610-2993 and you’ll get Hal or someone on the crew, not a phone tree.
Why Gatewood Fence & Gate Is Conyers’s Preferred Gate Parts & Welding Company
Hal Gatewood started this business in 2001 and he still runs it himself. That matters in Conyers because gates here fail in ways you only learn by working the ground. Red clay expands in the summer and shrinks in winter, posts heave, hinges bind, and ornamental iron cracks when ice gets into the pickets. We see it every week. More importantly, we fix the root cause instead of just swapping the visible part.
Every job from us carries the 90-Day Done Right Promise in writing. If something’s not right, one call brings us back. No runaround, no fine print. About half the Conyers homeowners we work with have already been burned by an outfit that quoted one number on the phone and billed another at the door. Our price gets quoted and agreed before any work starts. That’s the whole price.
We also answer the phone around the clock. A live person picks up at 2 a.m. when a storm just dropped a limb on your gate and the horses are still in the back forty. You can always drive to the shop and look Hal in the eye. The name is on the shop, and the shop is down the road. That’s the oldest accountability there is.
Our Gate Parts & Welding Services in Conyers
Our Gate Parts & Welding team covers the full range of repair work on both residential and agricultural gates in Conyers. Here’s what we do most often for neighbors in 30012, 30013, and 30094.
Hinge Replacement
A gate sags in the hinge post, not in the middle. That’s where we start. On Conyers HOA subdivisions built in the 1990s and early 2000s, the original hinges on ornamental iron gates are now 15 to 25 years old, and the barrel pins have wallowed out from years of red clay shifting the alignment. We cut the old hinge, prep the post face, and weld a new heavy-gauge hinge in place, then rehang the leaf so the reveal is even top to bottom. Hinge replacement in Conyers typically runs $240 to $480 per leaf depending on gate weight and post condition.
Post Replacement
Conyers sits on Georgia red clay, and that soil is the reason so many gate posts here lean. The clay swells when it rains and shrinks when it dries, lifting and tilting concrete footings year after year. A 6-inch steel post on a farm gate near the Georgia International Horse Park can end up over two inches out of plumb without anyone touching it. We dig out the old footing, set the post deeper, pour new concrete, and weld any brackets or hinges fresh. Post replacement in Conyers generally runs $350 to $700 for residential posts and $500 to $1,100 for larger farm gate posts depending on depth, diameter, and access.
Rail Repair
Ornamental iron rails crack at the welds, especially after an ice storm puts load on pickets that weren’t designed for it. On Conyers acreage gates, the top rail often sags from years of someone climbing over instead of opening the latch. We straighten what’s salvageable and weld in new rail sections where it’s not. If the panel is still sound except for one failed joint, we fix that joint. We don’t sell you a whole new leaf because one weld broke. Rail repair in Conyers usually runs $180 to $380 depending on the length and number of joints.
Custom Welding
Some gates can’t be repaired with off-the-shelf parts. Wide farm swing gates on acreage entrances, custom ornamental gates with curved scrollwork, utility panels welded onto ranch gates. For these we weld on site, in the driveway or at the gate post, with the gate still on the property. We fabricate hinge brackets, latch plates, stiffener gussets, and operators mounts to match the existing steel. Custom welding in Conyers typically runs $95 to $195 per hour plus materials, and most repair welds take under two hours.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Conyers
We’re certified to service nine major gate brands, and the three we see most on Conyers properties are LiftMaster, Viking, and Ghost Controls - for Conyers Gate Motor & Opener work. LiftMaster operators are everywhere on suburban HOA gates around 30094, Viking drives show up on the heavier acreage swing gates, and Ghost Controls solar kits are common on rural entrances where running mains power isn’t practical. We stock common control boards, arms, and limit switches for these brands so most Conyers repairs don’t wait on a parts order. If your opener is a DoorKing or an FAAC, we cover those too.
Common Gate Parts & Welding Problems We See in Conyers Homes
- Heaved posts on red clay. Conyers’s Piedmont clay swells with summer rain and shrinks in dry stretches, rocking concrete footings and pulling gate posts out of plumb. You can reset the post once, but if the footing is too shallow, it’ll tilt again in eighteen months.
- Stripped operator gears on wide farm gates. A 16-foot swing gate near the Horse Park weighs a lot, and when the hinge post sags, all that unsupported weight loads the opener’s gearbox until the teeth strip. Fix the post first, or you’ll fix the operator twice.
- Cracked welds from ice storms. Winter ice events hit Conyers every few years, and ornamental iron pickets and rail joints crack under the weight. What looks like a cosmetic split often hides stress that will propagate into a full separation at the next wind event.
- Lightning damage to control boards. Gates on open pasture land south of SR-138 are the tallest metal objects for a hundred yards. We replace surge-fried boards regularly on Conyers acreage properties, and we always recommend a surge suppressor on the new install.
Pricing for Gate Parts & Welding in Conyers, GA
Here are honest ranges for the work we do most in Conyers. Hinge replacement: $240 to $480 per leaf. Post replacement: $350 to $700 for typical residential posts, $500 to $1,100 for 6-inch farm posts. Rail repair: $180 to $380. Custom welding: $95 to $195 per hour, most repair welds done in one or two hours. The cost moves based on post diameter, gate weight, access, and how much concrete has to come out. What doesn’t change: the price is quoted and agreed before we touch anything, and we honor it. Call (877) 610-2993 for a free estimate. No trip charge inside the county, $40 off any repair over $200, and a permanent 10% discount for seniors and veterans.
We Also Serve Cities Near Conyers
If you’re just over the county line, we work Stonecrest, Redan, Snellville, and Stockbridge regularly. The drive is short and the red clay doesn’t stop at the city limits. Same crew, same 90-Day Done Right Promise, same phone number.
Serving Conyers, GA - Our Local Coverage Area
We’re based in the Conyers area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Conyers
Because the original footing was probably too shallow for Conyers’s expansive red clay. The clay swells when wet and shrinks when dry, cycling the soil around the concrete every season, and over a few years it walks a shallow footing right out of plumb. The fix is to excavate the old footing, go deeper, pour a new concrete collar with a wider base, and reset the post plumb. That holds. A surface-level reset just buys you a year. For a lasting fix, call (877) 610-2993 and we’ll quote the job before we dig.
Yes, in most cases. A crack in a picket or rail joint can be V-grooved, welded, ground smooth, and primed so the repair is nearly invisible after paint. We’ve done it on 1990s ornamental gates all over Conyers HOA subdivisions. The leaf only needs replacing when multiple joints have failed or the steel has rusted thin enough to compromise the structure. Call (877) 610-2993 and we’ll give you an honest read.
Yes. A 16-foot tubular steel farm gate weighs anywhere from 400 to 800 pounds depending on the build, and a suburban opener rated for a 12-foot decorative gate won’t survive that load for long. You need a heavy-duty linear arm or ram-style operator, and if mains power isn’t at the entrance, a solar kit with a matched battery bank. We spec and install Viking and Ghost Controls systems on Conyers acreage regularly. Call (877) 610-2993 for a recommendation matched to your gate’s actual weight and span.
No, that’s almost always post movement from seasonal clay expansion. In summer the wet clay swells, pushes the gate posts slightly toward each other, and the latch side binds. In winter the clay dries and shrinks, the posts relax, and clearance comes back. The welds are usually fine. The long-term fix is to reset the posts deeper so seasonal moisture changes below the footing don’t move them. We can confirm with a level and a string line in about twenty minutes. Call (877) 610-2993.
Yes. We unbolt or cut the hinges at the post face, support the gate in place with blocking, excavate and replace the post, then weld fresh hinge brackets to the new post and rehang the gate. The welded utility panel stays untouched. We’ve done exactly this on ranch entrances south of Conyers where the panel holds stock fencing and needs to stay intact. Call (877) 610-2993 and we’ll come measure and quote it.
Why Conyers Is a Two-Market Gate Town
Conyers is Horse Town USA, and it’s the reason gate work here looks nothing like gate work in Covington or Lithonia. Drive through the HOA subdivisions around 30094 and you’ll see 1990s and 2000s brick pillar entries with ornamental iron driveway gates, almost all of them now 15 to 25 years old and due for hinge replacement, Gate Access Control in Conyers updates, and operator rebuilds. Drive south and east toward the Georgia International Horse Park corridor, and the gates change completely: heavy tubular steel or wood-plank farm gates on 6-inch posts, swinging wide openings designed for trucks with horse trailers, often running on solar power because mains never reached that corner of the property.
Both markets share one failure mode: red clay. The soil under Conyers is expansive Piedmont clay that swells and shrinks with the seasons, which is why gates here bind in summer, sag in fall, and settle unevenly year over year. On a 1990s HOA gate, that shows up as hinge pins wearing out and operators fighting misalignment until the gears strip. On a farm gate, it shows up as a 6-inch steel post tilted two inches out of plumb, tearing hinge bolts right out of the post face. Last month our crew reset a sagging 16-foot farm swing gate off SR-138 south of Conyers. The 6-inch hinge post had been lifted over two inches out of plumb by red clay heave, tearing the top hinge bolts. We pulled the old post footing, repoured with deeper concrete, welded a new heavy-gauge hinge bracket, and added a solar gate opener so the owner no longer has to hand-swing it from the truck.
That’s the dual skill set this town requires. You need agricultural-grade hardware sourcing and full post-resetting capability for the Horse Park corridor, plus precise ornamental welding and control board diagnostics for the HOA subdivisions. One without the other means turning away half the jobs in Conyers. We don’t turn them away.
Repair First, Replace Only When It’s Actually Done
We fix gates. We don’t sell replacement gates to people who need a hinge. The national outfits that work Conyers have a different economic model: haul off the old gate, sell a new one, bill for disposal. That’s fine for them. It’s not how Hal runs a shop with his name on the invoice. If the post is good, we weld the hinge. If the rail is sound, we fix the joint. If the opener just needs a limit switch, that’s a $90 part, not a $1,800 operator. You should always know what’s actually broken before anyone talks about what’s getting replaced. Our Gate Parts & Welding philosophy is simple: fix the panel without the post and you’ll fix it twice. Fix the post and you’re done for a decade.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Conyers and the surrounding counties since 2001.