Gate Repair in Conyers - Same-Day Repair, Priced Before We Start

Gate Repair in Conyers, GA

Gate repair in Conyers, GA usually runs $185 to $485 for hinge and realignment work, $240 to $650 for electric opener and control board service, and $450 to $1,600 for full post resets on heavy farm gates. The single biggest reason gates fail here is the red clay under Rockdale County, which swells and shrinks with every wet-dry cycle and slowly pushes posts out of plumb. If your gate is groaning, sagging, or refusing to open as you’re backing out onto Salem Road, call (877) 610-2993 and a live person answers around the clock.

Call (877) 610-2993

Why Conyers Homes Are Different

Conyers sits on Georgia’s Piedmont red clay, and that clay is the most persistent saboteur of gates in this county. When summer rain saturates the soil, it swells and presses against post footings. When it dries in late summer, it shrinks and pulls away. The cycle tilts concrete-set posts a fraction of an inch at a time, and that fraction is enough to make a double gate bind at the strike, a slide gate drag on its track, or an actuator burn itself out fighting a load it was never meant to carry.

The housing stock compounds the issue. Most Conyers subdivisions were built during the 1980s through 2000s, and the ornamental iron automatic driveway gates from that build wave are now 15 to 25 years old. Actuators, control boards, and hinges that lasted two decades are reaching the end of their service life at roughly the same time their posts are going out of plumb.

Then there’s the equestrian side. Conyers is Horse Town USA, home to the Georgia International Horse Park, and the properties around that corridor carry a different class of gate entirely: 16-foot tubular steel swing gates on 6-inch posts, with livestock traffic and wind load working against every weld. A gate repair business here has to handle both the HOA ornamental iron and the farm-duty steel, which is exactly what we do.

Gate Repair in Conyers

Gate repair in Conyers splits into two worlds. On the subdivision side, you have 1990s and early 2000s ornamental iron driveway gates whose actuators are tired and whose control boards are corroding. On the farm side, you have heavy swing and slide gates where the red clay has heaved 6-inch steel posts out of plumb and the hinge welds are cracking from fatigue. We diagnose the whole system before we quote anything, so you’re not paying for a new opener when the real problem was a bad capacitor or a loose wire. Learn more about our Gate Repair service and what we can fix without replacing.

Electric Gate Repair

Conyers has hundreds of automatic driveway gates that were installed during the big eastward growth wave of the 1990s and early 2000s. Those systems are now fifteen to twenty-five years old, which means actuators are tired, control boards are corroding, and limit switches are out of adjustment. Expect electric gate repair in Conyers to run $240 to $650 depending on whether we’re replacing a board, rebuilding an actuator, or both.

Hinge & Post Repair

This is the Conyers special. A 6-inch steel post set in concrete can heave two inches out of plumb between a wet July and a dry October. When that happens, the gate binds, the hinges stress, and the welds start to crack from fatigue. We cut out the old post, bore deeper, set new concrete with proper drainage, and re-hang the gate so it swings true. On equestrian properties near the Georgia International Horse Park, that often means sourcing agricultural-grade hardware that the suburban guys don’t even stock. Full post resets on residential gates run $450 to $1,200, and on heavy farm gates with 6-inch posts the range is $800 to $1,600.

Gate Realignment

Sometimes the post is fine and the gate has just drifted. Hinge bushings wear, lag bolts loosen, and a gate that swung perfectly for a decade starts dragging a half inch at the latch side. We realign the leaf or leaves, shim or replace hinges, and adjust the latch and strike so everything closes without a fight. Realignment is usually the least expensive repair we do: $185 to $350 for most residential gates in Conyers. If the post has moved, though, we’ll tell you straight, because realigning without addressing the post means you’ll fix it twice.

Why do my Conyers gate posts shift so much more than my sister’s in Covington?

Because of the soil. Conyers sits on highly expansive red clay Piedmont soil that swells dramatically with rainfall and shrinks during dry stretches. Covington’s soil drains differently and doesn’t move as much. A post set in concrete here gets pushed and pulled every wet-dry cycle, which is why we bore deeper footers and add gravel drainage when we reset posts in Conyers. Call (877) 610-2993 and we’ll come assess yours.

My 20-year-old ornamental iron driveway gate in an HOA subdivision won’t close fully. Is it the motor?

Probably not. In Conyers HOA subdivisions built in the 1990s and 2000s, the most common cause of a gate that won’t close fully is post movement, not motor failure. The red clay heaves the hinge post, the gate drifts, and the operator’s limit settings can no longer reach the closed position. We’ll check the post plumb first, then the hinge bushings, then the operator. That order saves you from buying parts you don’t need.

Gate Installation in Conyers

Gate installation in Conyers typically runs $1,400 to $2,600 for a single-leaf ornamental steel driveway gate with a basic opener, and $350 to $900 for a pedestrian gate. Most jobs wrap up in one to two days once materials arrive. We know the red clay here, the HOA rules that apply inside neighborhoods like Honey Creek, and the farm gate requirements out along SR-138. See our full Gate Installation service for what a new gate includes.

Driveway Gate Installation

Driveway gates in Conyers neighborhoods like Honey Creek and East Lake Commons were mostly installed when the houses were built, fifteen to twenty-five years ago. A lot of them are ornamental wrought iron on brick pillar entries, and they are now due for hinge work, actuator replacement, or full replacement. A new automated driveway gate in Conyers generally runs $2,200 to $4,800, depending on width, material, and opener. Before the first post hole is dug, the price is in writing.

Swing Gate Installation

Swing gates are the classic Conyers look: two wrought-iron leaves meeting at the center of a brick pillar entry. They are also the gate type most vulnerable to our red clay. When the clay expands after a rainy summer, the posts move, and the leaves stop lining up. We set swing gate posts deeper than code minimums here, with extra concrete mass, because we know exactly how Conyers soil behaves. A wider double driveway gate runs $2,500 to $6,000 depending on material and opener quality.

Sliding Gate Installation

Sliding gates are the go-to for the bigger equestrian properties south and east of SR-138, where a swing gate would need a massive arc of clear ground that most farm layouts don’t have. The gate rides on a track and rollers instead of pivoting on hinges, which means it doesn’t care if the posts heave a little. Slide gates run $2,800 to $5,500 installed in Conyers, and we handle the power run, safety edges, and photo eyes as part of the job, not as add-ons.

Do you handle the power run and safety edges on a new gate install?

Yes. A full gate installation in Conyers includes the power run from the house to the operator, plus the safety edges and photo eyes. These are not add-on charges; they are part of a code-compliant gate installation. Hal insists on proper safety equipment because a gate without working safety edges is a gate that can hurt someone. We do not skip that to shave the bid.

Do you cover all Conyers neighborhoods and ZIP codes?

Yes, we cover all of Conyers, including ZIP codes 30012, 30013, and 30094. That includes the HOA subdivisions north of I-20, the neighborhoods along Flat Shoals and Brown Bridge Roads, and the equestrian properties out toward the Georgia International Horse Park corridor and SR-138. Call (877) 610-2993 for a free estimate.

Gate Motor & Opener in Conyers

Gate motor and opener repair in Conyers typically runs $240 to $600 for common failures like control board replacement or actuator rebuild, and most jobs are completed the same day we arrive. Heat and humidity in July and August push old electrolytic capacitors past their service life, and summer thunderstorms kill a lot of older control boards with voltage spikes. We stock common parts on the truck, which means the fix often doesn’t wait on shipping. See our Gate Motor & Opener service page for details.

Motor Repair

Roughly 60% of motor failures we see in Conyers are repairable without replacing the operator. A bad capacitor, a seized limit switch, a control board that got fried by a voltage spike from a summer thunderstorm. Motor repair here typically lands between $180 and $450. We don’t sell you a new unit because it’s easier for us; Hal would rather fix what’s fixable and tell you the truth about what’s not.

Motor Installation

A new gate opener installation in Conyers runs $1,800 to $4,200 installed, depending on gate size, weight, and whether we’re running new conduit from the house or upgrading an existing power run. We quote the number before any work starts, and that’s the number on your invoice. Installations on the subdivisions around the Georgia International Horse Park often mean working with brick pillar entries from the 1990s, which requires careful core drilling and anchoring that respects the masonry.

Slide Motor Repair & Installation

Slide motor work in Conyers runs $350 to $900 for repairs and $2,400 to $5,500 for a full heavy-duty installation. The gate trucks and track on these systems take a beating from red clay runoff, and we regularly rebuild guide wheels, replace worn chain, and re-bed track that has been lifted by soil expansion. On-site welding means we fabricate brackets and mounts right there at the gate, which saves a second trip and keeps the job moving.

Can you come today if my gate motor stopped working in Conyers?

Most gate motor repairs in Conyers are same-day when you call before early afternoon. We keep common control boards, capacitors, and Linear replacement parts on hand, which means the fix often doesn’t wait on shipping. Call (877) 610-2993 and we’ll tell you realistically when we can be there. You’ll get a straight answer, not a four-hour window that turns into tomorrow.

What kind of warranty do I get on a gate motor repair in Conyers?

Every job, including motor repair and opener installation in Conyers, carries our 90-Day Done Right Promise in writing. If it’s not done right, we make it right. That’s not “up to 90 days” or “in most cases.” It’s 90 days, stated plainly, with Hal’s name on it. If something isn’t right, one call brings him back.

Gate Access Control in Conyers

Gate access control repair in Conyers typically runs $220 to $480 for a control board or keypad replacement. If your driveway gate won’t open from the keypad, the remote, or your phone, you’re usually dealing with one of three things: a failing control board on a 15 to 25 year old operator, a hinge post that Conyers’s red clay has heaved out of plumb, or a loop detector that no longer senses your car. We test before we replace, which means you’re not buying a new keypad when the board behind it is the real failure. See our Gate Access Control service for more on what we service.

Phone Entry Systems

Phone entry is the single best retrofit for older Conyers gates, especially the 1990s HOA installs. Instead of replacing a dead intercom or handing out keypad codes that everyone shares, we tie a phone entry module into your existing operator. Visitors pull up, tap a name on the directory, and the gate rings the resident’s cell phone. On legacy DoorKing and Linear operators, this retrofit usually costs between $650 and $950, and it logs who came in.

Keypad Entry

Keypads are simple, and simple is good until Conyers weather gets to them. The Georgia sun bakes the membrane, and the red clay dust that kicks up off driveways works its way into the housing. A dead keypad on a 20 year old gate is often just the visible symptom of a failing control board underneath. A standalone keypad replacement in Conyers runs $180 to $320. If the board is gone too, we’ll say so plainly and give you the number for both before we touch anything.

Loop Detector Calibration

The gate won’t auto-open when you drive up from inside. That’s the loop detector under the driveway losing sensitivity. It’s incredibly common on Conyers HOA gates where the original installers never re-aimed the loop after the brick pillars settled. Loop detector calibration or replacement runs $150 to $250, and it’s one of the cheapest fixes that makes a gate feel brand new again.

My 1990s HOA gate in 30094 still has a keypad, but residents keep getting locked out. Is the keypad the problem?

Usually not. On 1990s HOA gates in 30094, the keypad is the part you can see, but the failure is almost always behind it: a dying control board that’s misreading keypad input, or a loop detector that’s drifted so badly the exit sensor doesn’t see cars. We test the keypad first, then the board, then the loop. Call (877) 610-2993 for an exact quote.

Can a phone entry system be added to a legacy FAAC or BFT operator on a rural horse farm gate?

Yes, in most cases. FAAC and BFT operators on rural Conyers horse farm gates are built for heavy gates, and they’ll usually accept a phone entry module as long as the operator has a working control board and a 24V accessory output. We’ve done this on farms around the Georgia International Horse Park and south of SR-138, adding phone entry so a trainer, vet, or hay delivery can reach the property without a shared code.

Gate Parts & Welding in Conyers

When a gate hinge tears loose or a post leans out of plumb in Conyers, you need someone who knows the difference between a 1990s HOA ornamental iron gate and a farm swing gate on SR-138. We weld on site, in your driveway or at the barn, which means the gate stays where it is and we fix it there. Hauling a gate off and swapping it rarely makes sense when the steel is sound. See our Gate Parts & Welding page for the full picture.

Hinge Replacement

Wrought-iron driveway gates built in the 1990s and early 2000s across Conyers HOA subdivisions are hitting the age where the barrel hinges seize, crack, or tear free from the post. On red clay, the post has usually shifted too, so a new hinge alone won’t solve the bind. In Conyers, hinge replacement on a standard ornamental single driveway gate typically runs $145 to $290, depending on post condition and whether we’re doing one hinge or the full set.

Post Replacement

Conyers sits on expansive Georgia red clay. It swells when the summer rains come and shrinks in the dry weeks, and over a decade or two that cycle heaves steel posts out of plumb. You’ll see the gate strike missing the latch or dragging across the ground. Post replacement in Conyers generally runs $280 to $580 for a typical ornamental gate post, more if we’re pulling a 6-inch farm gate post out of concrete at a horse property near the Georgia International Horse Park.

Custom Welding

Not every fix is a replacement. A snapped latch bracket, a cracked bottom rail on a farm gate, a torn support gusset on a sliding gate: these are the jobs where hauling the gate off and swapping it makes no sense. Hal’s been under a hood since he started this trade, and if the steel is sound enough to save, that’s what we do. Custom welding rates in Conyers run $95 to $165 per hour plus materials, and most single-repair weld jobs come in under $400.

Do you offer emergency gate welding in Conyers?

Yes. A broken gate on a horse property or a driveway gate that won’t close is a security issue, and we treat it like one. Our phones are answered 24 hours a day, and a live person will get you scheduled. If the gate is holding animals and it’s coming apart, we’ll move fast. Call (877) 610-2993 and tell us what’s failing.

Is gate welding in Conyers more expensive than the surrounding cities?

No, our pricing is the same across our service area. You’re paying for the repair, not the drive. Hinge replacement stays in the $145 to $290 range whether you’re in Conyers or Stockbridge, and post replacement runs $280 to $580 everywhere we work. The 90-Day Done Right Promise applies to every weld, every hinge, every post.

Brands We Service in Conyers

We service Viking, Ghost Controls, DoorKing, and Elite systems across Conyers, and we keep common replacement parts stocked for each on the truck. That means a control board swap or a hinge rebuild on one of these brands usually doesn’t wait on a parts shipment. See our brands for the full list of what we’re certified to work on.

Pricing for Gate Repair in Conyers, GA

Neighborhoods We Serve in Conyers

We run repair calls across the full Conyers footprint and schedule by area so response time stays tight. Typical response is same-day to next-day for most repairs, and no trip charge applies anywhere inside the county.

• Horse Park corridor near the Georgia International Horse Park
• Oak Hill and Irwin Place subdivisions off Salem Road
• Almand Creek and Honey Creek communities
• Rural acreage along SR-138 and Smyrna Road
• Springfield and Ellington subdivisions east of I-20

Service Area - Cities Near Conyers

We work Conyers every week, and we also serve the surrounding communities across Rockdale and DeKalb counties. If you’re in Conyers, GA, you’re already in our core territory. We also cover Stonecrest, GA, Redan, GA, Snellville, GA, Stockbridge, GA, and Stone Mountain, GA. Same pricing, same 90-Day Done Right Promise, same live person on the phone.

FAQs About Gate Repair in Conyers