Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Marietta, GA
When a gate stops opening in Marietta, the motor is rarely the first thing that failed. The post has shifted in the red clay, a hinge has bound, or a control board took a surge during one of our July thunderstorms. Call (877) 610-2993 and you’ll get a live person, a straight answer, and a fix that happens in your driveway, not in some shop across the county.
Why Marietta Homes Are Different
Marietta sits on heavy Georgia red clay, and that clay doesn’t hold still. Between a wet winter and a dry summer, the soil swells and contracts enough to shove gate posts out of plumb. Technicians who know Marietta check footing depth first. Posts installed at 24 inches, standard in the 1985-2005 subdivision buildout, heave noticeably each winter. The real fix often means resetting the post into the stable subsoil layer, which is a different job than tightening hardware, and it’s the difference between a gate that works for a decade and one that’s leaning again by spring.
Marietta’s summer storms are the second problem. Our humid subtropical climate produces frequent thunderstorms from May through September, and lightning strikes and power surges regularly cook automated gate operator circuit boards. That’s why we carry common replacement boards on the truck during storm season. In East Cobb’s 30062 and 30066 ZIPs, where HOA-governed gated subdivisions are most dense, the combination of aging ornamental iron, shallow footings, and storm surge means we see the same failures week after week. The housing stock tells the story: 1980s and 1990s master-planned subdivisions where ornamental iron and black aluminum gates were installed as standard amenities, and now those systems are hitting their 20-to-40-year end-of-life window all at once.
Gate Repair in Marietta
Gate repair in Marietta usually runs between $180 and $650 depending on whether we’re resetting a red-clay-heaved post, replacing hinges, or swapping a fried control board. The work we do here is shaped by what this city’s soil and weather do to a gate over twenty or thirty years. Our repair philosophy is simple: fix what’s broken, weld on site, and don’t replace a panel when the post is the problem.
Electric Gate Repair
When an electric gate in Marietta stops responding, the first thing we check is whether the control board got hit by one of our summer thunderstorms. From May through September, this is the single most common service call we make in this city. A power surge fries the motherboard, and now the gate sits dead or opens in one direction only. Board replacement typically runs $275-$500 including parts and diagnostic labor. We stock boards for FAAC, BFT, Linear, and Viking on the truck, so when the board is the culprit, we usually fix it in one visit.
Automatic Gate Repair
Your automatic gate depends on a lot of small parts agreeing with each other: limit switches, safety sensors, the receiver that talks to your remote, the motor itself. In Marietta, we’ll often trace an automatic gate failure back to the red clay under the post rather than anything electrical. If the post shifted even half an inch, the gate binds against the strike plate, the motor struggles, and the limit switch trips early. The whole system looks broken when it’s really just out of square. We test each component before replacing anything, and when the post is the root cause, we say so. Full operator replacements start around $900 for a residential swing arm.
Hinge & Post Repair
Here’s what you need to know about gates in this city: Georgia red clay expands when it’s wet and shrinks when it’s dry, and it does this every single year. Post footings poured to the 24-inch depths that were code-compliant during the 1985-2005 building boom don’t resist that movement well. Once a post leans out of plumb, the hinge takes lateral load it was never built for, and eventually the weld cracks or the hinge pin bends. Post resetting, the fix we do most often in the East Cobb corridor, usually runs $400-$700 depending on how deep we have to go to hit stable subsoil and how much concrete surrounds the existing footing.
Gate Realignment
A gate that scrapes the driveway or won’t close flush against the post is telling you something about its structure. In the 30062 and 30066 ZIPs, this usually means a gate that withstood decades of wet-dry soil cycles and big oak-root growth nobody planned for during the original install. A hinge and re-hang on a standard ornamental steel driveway gate runs $180-$340, depending on whether we’re doing one hinge or three and how much the post has moved. Realignment involves re-plumbing the post, resetting the hinges, and bringing the leaves back to a gap that closes cleanly without dragging. We do the full scope of Gate Repair work in Marietta, from a single hinge to a complete post reset.
How fast can you get to my gate in Marietta?
Most Marietta repair calls are reached the same day, and in many cases within a few hours, especially if you tell us the gate is stuck open and nobody’s home. A live person answers at (877) 610-2993 around the clock, and we’ll give you a straight answer about when we can be there. If it’s an emergency and the gate won’t close, call now.
Do you cover HOA gate repair in Marietta subdivisions?
Yes, we do both private driveway gates and shared HOA entrance gates in Marietta. Many of the calls we take in the 30062 area involve a control board that serves the whole neighborhood. We handle those just like a single-family gate: upfront pricing, a written estimate before work starts, and the same 90-Day Done Right Promise on the finished job. Call (877) 610-2993 for a free estimate.
Gate Installation in Marietta
Gate installation in Marietta typically runs $2,800 to $9,500, and what drives the price is usually what’s under the ground, not what’s above it. We see this every week across 30008, 30060, 30061, and 30062, especially in the East Cobb corridor where hundreds of HOA communities built between 1985 and 2005 are now dealing with ornamental iron and automated swing-gate systems hitting their replacement window all at once. When we install a gate here, we set posts deeper than the original builder did.
Driveway Gate Installation
Most Marietta driveway gates we install replace aging ornamental iron or aluminum systems in East Cobb subdivisions. The old post is usually the culprit. We dig down past the clay layer and set the new post in stable subsoil, not the 24-inch footing that failed the first time. Typical driveway gate installs run $3,200 to $9,500 depending on width, material, and whether you’re adding an operator.
Swing Gate Installation
Swing gates remain the most popular choice in Marietta, especially double swing gates for wider driveways. The challenge here isn’t the gate itself. It’s the post footings in our red clay soil. We pour deeper, use proper drainage, and make sure the hinges carry the load evenly. Single swing gate installs start around $2,800, and double gate systems with operators run $6,000 to $12,000. You can see the full scope of our Gate Installation work, including material options that hold up in Marietta’s humidity.
Sliding Gate Installation
Sliding gates work well on Marietta properties where a swing gate would block a sloped driveway or eat into limited frontage. We install single and double-slide systems, often pairing them with a gate motor for automation. Expect $4,500 and up for a solid sliding gate with a track, depending on length and weight. The operator you select matters too, with FAAC and BFT sitting at the premium end.
What does gate installation cost in Marietta compared to Smyrna or Kennesaw?
Marietta pricing is generally in line with the rest of metro Atlanta, but older HOA stock and the need for deeper footings in red clay can add $300 to $800 compared to newer developments in Kennesaw with better-drained soil. A typical single swing driveway gate with an operator in Marietta runs $4,800 to $8,500. Call (877) 610-2993 for an exact quote.
Can you handle HOA requirements for my Marietta subdivision?
Yes. We’ve installed gates in dozens of HOA-governed communities across East Cobb and beyond. We review your architectural guidelines before quoting so the gate height, material, color, and style comply with your covenant. If the board needs documentation, we’ll provide the specs. Call (877) 610-2993 and we’ll come measure.
Gate Motor & Opener in Marietta
Gate motor repair in Marietta typically runs $240-$580 for control board, capacitor, or limit switch work, while full operator replacements on heavy ornamental iron gates in East Cobb usually land between $1,400 and $3,200 depending on the gate’s weight, length, and whether we’re retrofitting or starting fresh. We stock parts locally, so most Marietta driveway gate failures get fixed in one visit, not three. The motor is almost never the first thing that fails here; it’s usually what kills the motor that matters, and in this city that means red clay and lightning.
Motor Repair
If your gate opener clicks, hums, opens halfway, or trips its breaker every time it rains, we’ll find the cause. In Marietta, the single most common issue we see from May through September is lightning damage to control boards. Board replacements typically run $280-$520 including the part and diagnostic labor. Capacitor failures on older FAAC and LiftMaster operators are another frequent repair, usually $140-$220. We quote the exact number before any work starts, and that number doesn’t move. Read more about our Gate Motor & Opener service for the full list of what we repair.
Motor Installation
We install gate operators on new and existing driveway gates throughout Marietta. Most of what we do is retrofit work on 80s and 90s ornamental iron gates that were built well but powered by operator brands that have since gone obsolete. A typical Marietta homeowner replacing an old swing gate motor with a new LiftMaster or FAAC unit will run $1,600-$2,900 including operator, bracket fabrication, wiring adjustments, and safety-edge or photo-eye integration.
Slide Motor
Slide gates are the workhorse motor type across Marietta’s HOA communities, especially where driveway geometry doesn’t leave room for a swing arc. We install and repair rack-and-pinion slide operators, chain-driven units, and the heavier Viking and Elite units you see on community entrances off Johnson Ferry Road and Lower Roswell Road. Motor replacement on a residential slide gate usually runs $1,700-$3,000, more if the existing rack is worn and needs replacing.
Why do gate operators in East Cobb Marietta fail more often than in Roswell or Smyrna?
East Cobb’s gate operators fail more often because heavy ornamental iron gates, HOA-era installation practices from 1985-2005, and metro Atlanta’s most heave-prone red clay create a stress profile that Roswell’s sandier soils and Smyrna’s commercial streetscape simply don’t produce. The clay expands and contracts seasonally, shifting posts and pulling gates out of alignment. A misaligned gate then destroys limit switches and burns out motors. Call (877) 610-2993 for an evaluation.
Can you integrate a new gate motor with an existing intercom and camera system in a Marietta HOA community?
Yes, we integrate new gate motors with existing intercom, keypad, and camera entry systems every month in Marietta’s HOA-governed subdivisions. Most 2000s-era entry systems use dry contact relays for gate triggering, which means the new operator’s control board gets wired into the same trigger circuit the old one used. Call (877) 610-2993 and we’ll look at your setup.
Gate Access Control in Marietta
Gate access control in Marietta means keypads, phone entry, video intercoms, card readers, and the wiring and operators behind them. For most Marietta homeowners and HOA communities, the real question isn’t whether the system can be fixed. It’s whether the person showing up understands how an access system ties into a gate that has been shifting in red clay for 25 years. That’s where we come in, and we answer the phone ourselves.
Keypad Entry
Keypad entry is the most common access point on Marietta’s gated communities, and it fails in predictable ways here: sun-cracked housings, corroded contacts after a wet spring, and code drift from control boards that took a nearby surge. A new keypad entry installation typically runs $350-$650 depending on whether the wiring is already in place or we’re pulling new conduit. If you’re in a neighborhood off Johnson Ferry or Roswell Road, we can usually have someone there fast.
Phone Entry
Phone entry systems link the gate call box to a landline or cell number, so a visitor dials your lot and you punch in a code to open the gate. In Marietta subdivisions built in the 1990s, a lot of these systems are running on original phone-line hardware that was never meant to survive thirty Georgia summers. A phone entry system with a new call box and directory programming falls between $800-$1,900 on shared community gates. We replace aging call boxes, update the directory, and program emergency access for fire and law enforcement.
Card Reader
Card readers are common on Marietta’s larger community gates and commercial entrances off Cobb Parkway and Barrett Parkway. We install and service proximity readers, set access levels for residents versus vendors, and audit the system when an HOA board changes management companies and nobody can find the master card. If your reader quit reading overnight, we check the power supply first. Red clay soil and old underground conduit are a rough combination in Marietta’s wet winters. See our Gate Access Control page for what a full system involves.
Can a lightning strike really kill my gate access control system even if the gate still moves?
Yes, and it happens all over Marietta every summer. A nearby strike doesn’t have to hit the gate directly. It induces a voltage spike through the underground power line or the keypad wiring, and the first thing it takes out is usually the control board’s low-voltage circuit. The gate may still move manually, but code entry and phone entry stop working. Call (877) 610-2993 for a quote.
Does replacing a gate operator in a Marietta HOA community require architectural approval first?
In most Marietta HOA-governed subdivisions, yes, replacing a gate operator or changing the access system requires written approval from the architectural review committee or management company, particularly if the operator type or keypad placement changes. We can provide the cut sheets and spec documents the committee needs so approval doesn’t stall the repair while the gate stays dead. Call (877) 610-2993.
Gate Parts & Welding in Marietta
Gate parts and welding in Marietta usually means one of two things: a hinge that finally let go after thirty years of Georgia humidity, or a post that the red clay shoved out of plumb. We handle both, and we do it in the driveway. Hal Gatewood has been fixing gates since 2001, and the fix is usually measured in hours, not weeks. If your ornamental iron gate is sagging, dragging, or stopped, we can usually weld it right where it hangs.
Hinge Replacement
A gate sags in the hinge post, not in the middle. That’s the first thing to understand. When an ornamental gate starts dragging on the latch side, most people look at the middle of the panel. The real problem is the hinge barrel, which has worn egg-shaped after decades of swing cycles. We cut the old barrel off, weld on a new one, and the gate picks up off the ground. Hinge replacement runs $180 to $340 per hinge. In Marietta, where a huge percentage of gates are ornamental iron from the 1985-2005 buildout, this is our bread-and-butter repair.
Post Replacement
This is the big one. Marietta’s red clay heaves every winter. A post set 24 inches deep moves with the clay, pulling the gate out of plumb and putting permanent lateral stress on the hinges, the latch, and the operator’s limit switches. The real fix isn’t tightening bolts. It’s digging out the old footing and setting a new post down to the stable subsoil layer, usually 36 to 42 inches in East Cobb’s clay. Post replacement with deep-footing reset runs $550 to $1,200. Then we weld the hinge barrels back on at the right height and re-hang the panel. See our Gate Parts & Welding page for the full breakdown of what’s involved.
Custom Welding
When a vehicle taps a gate, or a tree limb comes down on a rail, the damage is rarely standard. That’s where custom welding comes in. We can fabricate and weld replacement pickets, scrollwork, hinge brackets, and latch plates to match your existing gate. For Marietta’s high-end properties, where gates are bespoke and often original to the subdivision, matching the ironwork matters. You don’t want a repair that looks like a repair. Custom scrollwork or picket welding starts at $180.
Why do so many ornamental gate posts lean in Marietta’s East Cobb subdivisions?
Red clay heaves every winter, and posts set at the 24-inch depth common in 1985-2005 buildouts move with the topsoil. We excavate the original footing, extend the hole down to 36 to 42 inches, drop in a new post, pour the footing, and weld the hinge barrels back on before re-hanging the panel. In East Cobb’s clay, 36 to 42 inches reaches stable subsoil that doesn’t move with the seasons. Call (877) 610-2993 for a free estimate.
How deep should a gate post be set in Marietta to avoid seasonal heaving?
In Marietta’s red clay, a gate post should be set 36 to 42 inches deep, not the 24 inches many subdivision builders used in the 1985-2005 era. The top 18 to 24 inches of Georgia clay expands and contracts with moisture, which is exactly where a shallow post sits. It moves every winter. The fix is a deep-footing reset and proper drainage around the footing. Call (877) 610-2993 and we’ll come look at your post.
Brands We Service in Marietta
We service and carry parts for the major gate brands on our trucks: FAAC, BFT, Linear, and Viking. That means faster turnaround when your operator board goes down during a storm. See our brands page for everything we stock and service.
Pricing for Gate Repair in Marietta, GA
| Service | Typical range in Marietta |
|---|---|
| Gate realignment with hinge and post adjustment | $180 - $340 |
| Control board replacement after lightning surge | $275 - $500 |
| Post reset into stable subsoil | $400 - $700 |
| Hinge replacement (per hinge) | $180 - $340 |
| Post replacement with deep-footing reset | $550 - $1,200 |
| Rail repair (per section) | $220 - $480 |
| Custom scrollwork or picket welding | Starts at $180 |
| Gate opener motor replacement (board and motor) | $450 - $900 |
| Full operator replacement (residential swing arm) | Starts around $900 |
| Full gate and operator installation | $2,800 - $7,500 |
What pushes price up in Marietta is almost always what’s under the gate: red clay heave, shallow original footings from the 1985-2005 buildout, and post lean that means more excavation and concrete work. The price we quote before we start is the price you pay. No trip charge inside the county, and the number is written down and agreed to before any work begins.
Neighborhoods We Serve in Marietta
We’re running calls across Marietta every week, and the truck is usually in your area quickly. Typical response for repair work is same-day or next-day depending on the neighborhood and the time of year.
- East Cobb (30062, 30068)
- Windsor Oaks (30062)
- Sandy Plains Road corridor (30066)
- Providence / Lost Mountain area (30064)
- Whitlock Avenue / Historic Marietta (30064)
Service Area - Cities Near Marietta
Rooted in Marietta, GA, we also serve the surrounding communities where the same red clay and storm patterns take the same toll. You’ll find us in Fair Oaks, GA, Smyrna, GA, Vinings, GA, Kennesaw, GA, and Sandy Springs, GA. If you’re near any of these, call (877) 610-2993 and we’ll get you scheduled.
Serving Marietta, GA - Our Local Coverage Area
Gatewood Fence & Gate crews serve Marietta and the communities around it; dispatch is coordinated from our Atlanta office. The map shows the Marietta coverage area; if your address is on it, we can help.
Also serving nearby: Marietta, GA, Fair Oaks, GA, Smyrna, GA, Vinings, GA, Kennesaw, GA, Sandy Springs, GA.
FAQs About Gate Repair in Marietta
In most Marietta neighborhoods, repairing an existing gate doesn’t require a permit. Replacing a gate with a new structure, especially on a shared HOA entrance, often does, and most HOA-governed subdivisions in East Cobb require architectural review first. We can pull the requirements for your specific property and handle the paperwork. Call (877) 610-2993.
A hinge replacement or control board swap is often done in one visit, usually within an hour or two. A post reset into stable subsoil takes longer because the concrete has to cure before we re-hang the gate. That’s typically a two-day job. We’ll tell you the timeline before any work starts, and the written estimate includes it.
Georgia red clay expands when it’s wet and shrinks when it’s dry, and Marietta’s wet winters soak the top 18 to 24 inches of soil. Posts set at that shallow depth during the 1985-2005 buildout heave upward, then settle unevenly in summer. Each cycle nudges the post out of plumb a little more. The real fix is a deep-footing reset. Call (877) 610-2993 for a free estimate.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Marietta Customers Say
"He came out in the snow to get our gate closed after a delivery lorry clipped it, then came back in the spring to do the proper repair when the ground had thawed. Only charged for the second visit."
- Ingrid Solheim"The fence is excellent and it was fairly priced. He is not quick to answer email, so if you need him, ring. He always picks up the phone."
- Rodney Falkenrath"Safety photo eyes on our old gate had been bypassed by whoever serviced it last, which he was genuinely annoyed about on my behalf. Fitted proper sealed ones and wired them the way they should be."
- Otis Redmond