Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Marietta
Gate parts and welding in Marietta usually means one of three things: a hinge that finally let go, a post the red clay heaved out of plumb, or an operator board that took a lightning hit. We handle all three, and we fix the root cause instead of dressing up the symptom. Hal Gatewood has been at this since 2001, and the shop answers the phone around the clock. If your gate is dragging, leaning, or dead, call (877) 610-2993 and a real person will pick up.
We run crews into Marietta every day, from the East Cobb subdivisions off Johnson Ferry Road to the older lots near Marietta Square. We know these gates because we have been welding on them for decades. That matters when the difference between a $200 hinge repair and a $2,000 post replacement comes down to how deep somebody buried the footing back in 1995.
Why Gatewood Fence & Gate Is Marietta’s Preferred Gate Parts & Welding Company
Hal Gatewood’s name is on the shop, the truck, and every invoice. You can drive to the shop and look him in the eye, or you can call and talk to a live person at two in the morning. Nobody in Marietta gets routed to a voicemail or a call center. That’s the oldest accountability there is, and it’s the reason we keep getting called back by the same homeowners year after year.
The crew works the same neighborhoods you live in. We have repaired ornamental iron driveway gates in Indian Hills, re-welded broken gate frames near Walton High School, and replaced post footings in subdivision after subdivision across 30062 and 30066. Background-checked and uniformed, the person who shows up is the person Hal trusts to do the work his name goes on. And every job carries the 90-Day Done Right Promise, stamped in writing. If it’s not done right, we make it right. One call brings him back, no runaround.
When a gate sags in the hinge post, not in the middle, that’s where we start. That’s not marketing copy. That’s what experience in Marietta’s soil actually teaches you, and it’s the difference between a repair that lasts five years and one that lasts five months.
Our Gate Parts & Welding Services in Marietta
We stock a deep bench of hinges, rollers, rack and pinion, latches, locks, and operator parts for the brands most common in Marietta subdivisions. But half of what we do is fabrication, not parts-swapping. Here’s where most of our Marietta work actually happens:
Hinge Replacement
Every automated swing gate in Marietta eventually kills a hinge. The leaf gets heavier each time the clay shifts under the post, and the hinge pin slowly egg-shapes its barrel until the gate scrapes the driveway. We replace the hinge, but we also check the post plumb before we weld anything back on. Fix the panel without the post and you’ll fix it twice.
Post Replacement
This is the big one in Marietta. Most gate posts in the 1985-2005 HOA subdivisions were set 24 inches deep, which is fine in stable soil but not in Georgia red clay. The clay heaves with every wet winter and dry summer, and the post leans. We cut out the old footing, dig into the stable subsoil, reset the post, and weld any reinforcement the gate needs before hanging it back up. The correction is surgical, not cosmetic.
Rail Repair
Wrought iron and black aluminum rails crack where they carry the most stress, usually at the picket welds or where the rail meets the stile. We grind, weld, smooth, and match the finish as close as the existing patina allows. If your HOA has a specific gate profile in 30062 or 30068, we match it. Period.
Custom Welding
When a torn lower hinge mount or a snapped scroll detail needs replaced on a 20-year-old ornamental gate, you can’t order that off a shelf. Hal welds it in your driveway, on site, so the gate never leaves the property and the metal matches what’s already there. Custom brackets, reinforcement plates, replacement pickets, gate extensions, operator mounting plates. If it’s steel or iron, we can probably make it right there in the truck.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Marietta
We are certified to service nine major gate operator brands, including Viking, DoorKing, and Ghost Controls, which covers the majority of what’s out in the East Cobb subdivisions and the gated entrances off Roswell Road. When we say “service,” we mean we actually repair them. Not sell you a new one because the old one had a bad capacitor. Parts for common failures live on the truck, which means fewer return trips for Marietta customers. If we have to order something odd, we’ll tell you upfront what it costs and when it shows up.
Common Gate Parts & Welding Problems We See in Marietta Homes
- Shallow post footings heave in red clay. The 24-inch footings common to 1980s-2000s Marietta subdivisions push posts out of plumb every winter. Sag correction here usually means resetting the post, not just swapping the hinge. We have seen posts lean a full three inches over a decade while the gate still limped along on the old hardware.
- Lightning kills operator boards from May through September. Marietta’s afternoon thunderstorms are rough on automated gates. A close strike takes out the LiftMaster or FAAC control board, and the gate goes dead or the keypad stops talking to the operator. We keep common boards and surge suppressors stocked for quick repairs.
- Corroded hinges bind and burn out limit switches. Humid air plus thirty-year-old iron means rust where the hinge pin meets the barrel. The operator keeps pushing against that resistance, the amperage spikes, and the limit switch fails. We fix the hinge and the switch, not just the switch.
- Ornamental details crack at stress points. The scrollwork and finials on older ornamental iron gates crack where the leaf flexes. A broken picket weld is annoying. A broken rail weld is dangerous on a heavy swing leaf. Both are quick on-site welding repairs when caught before the leaf sags onto the driveway.
Pricing for Gate Parts & Welding in Marietta, GA
A hinge replacement on a standard driveway swing gate in Marietta typically runs $180 to $340, including the hinge and on-site welding. Post replacement is bigger, $650 to $1,400 for a single post depending on depth, diameter, and whether the gate is automated. Rail repair and custom welding range from $150 for a simple crack or bracket to $900 or more for a structural rebuild of a large leaf. Operator board replacement after a lightning strike usually lands between $250 and $480 for the part and labor.
What changes the number is what’s underneath the post, and how much metal has to come apart to get to it. You’ll get a written quote before any work starts. That’s the number you pay. If another company gave you a written estimate for Marietta work, bring it to us and we’ll give you a free second opinion. We also knock $40 off any repair over $200, and there’s no trip charge inside the county. Seniors and veterans get 10% off, every time, no haggling.
We Also Serve Cities Near Marietta
Our crews work Marietta daily and run into Fair Oaks, Smyrna, Vinings, and Kennesaw on the same schedule. If you’re in one of those cities and need Gate Parts & Welding, the same crew, the same pricing, and the same 90-Day Done Right Promise applies. If you’re in Marietta proper, you’re already in our backyard. See where we serve around Marietta and give us a call.
Serving Marietta, GA - Our Local Coverage Area
We’re based in the Marietta area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Marietta
Because the problem isn’t the hinge. It’s the footing. In Marietta’s East Cobb corridor, most gate posts from the 1985-2005 subdivision boom were set 24 inches deep in Georgia red clay, which heaves with winter moisture and shrinks in summer dry spells. The post leans, the gate sags, and no new hinge will fix that. The permanent repair is digging out the old footing, resetting the post into stable subsoil, and re-hanging the leaf. Call (877) 610-2993 and we’ll come check the post plumb before you spend money on another hinge.
Yes. We match the existing profile, scroll pattern, and finish as closely as the existing metal allows. Most of the ornamental iron in the 30062 and 30066 subdivisions came from a handful of regional fabricators, so we’ve seen nearly every common pattern. If your HOA requires a specific spindle or finial design, we can replicate it or fabricate a close match and photograph it for approval before we finish the paint.
Lightning strikes on Marietta gates typically take out the main control board first, then the keypad or loop detector input if the surge rode in on the access wiring. We replace the board, check the transformer and backup battery, and add or replace surge suppression on the line so the next strike doesn’t do the same thing. A new board installed for a Marietta gate usually runs $250 to $480 parts and labor. Call (877) 610-2993 and we’ll diagnose the board on the spot.
Yes, more than most people expect. An underground operator lives inside a steel or poly box buried at the hinge post, and if that box isn’t set below the frost heave line and bedded in stable subsoil, the red clay will work it out of alignment the same way it leans the post. The gate then grinds against the box and the operator burns out. When we install or service underground operators in Marietta, we set the box deeper than the standard 24-inch subdivision footing and anchor it to the post foundation, not the soil surface.
Sometimes. A grinding rack and pinion usually means the rack is misaligned from the gear, the gate is sagging onto the track wheels, or the rack itself has cracked at a weld point. We inspect the whole track, weld any broken rack mounts back square, replace the rack segments that are chewed up, and set the gate back on line. If the post shifted, we address that first. The grinding sound is a symptom, and the fix is almost always more than just replacing the gear.
Call Gatewood Fence & Gate for Gate Parts & Welding in Marietta
If your gate is dragging, leaning, or dead after a storm, call (877) 610-2993. A live person answers, day or night. We’ll give you a straight answer about what’s wrong and what it costs to fix it, before any work begins. Free estimates, no trip charge in the county, and a 90-Day Done Right Promise on every job we do in Marietta.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Marietta and surrounding communities with gate repair, installation, and on-site welding since 2001.