Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Whitney
When a welded gate frame cracks or a wrought-iron hinge tears out of a CMU block wall here in Whitney, you need a welder who knows the dirt under the post and the sun on the panel. Gatewood Fence & Gate fixes gates the right way: on site, in your driveway, with hot work done by someone whose name is on the invoice. Hal Gatewood has been doing this since 2001, and when you call (877) 610-2993, a live person answers, day or night. No call center, no voicemail maze. We run crews into the 89122 ZIP six days a week, and a lot of Whitney repairs we quote in the morning get welded by afternoon.
Why Gatewood Fence & Gate Is Whitney’s Preferred Gate Parts & Welding Company
Whitney gates fail in predictable ways. The houses off Boulder Highway and along Tropicana were mostly framed between 1975 and 2000, which means a whole lot of steel swing gates hung on lag hinges set into block mortar that has been cooking and freezing for thirty-plus years. We see the same pattern over on the streets around Whitney Mesa: the hinge post is the first thing to go, not the gate leaf. A national outfit will quote you a brand new gate. We will show you the post is the problem, weld in a proper anchor, and leave your original gate on its hinges. That’s the owner-operated difference. Our Gate Parts & Welding crew does the work with the gate lying on sawhorses in your own yard. You watch the whole repair happen. And every job carries the 90-Day Done Right Promise in writing.
People around Whitney have seen enough fly-by-night crews to recognize the difference. A live person picks up the phone at 3 a.m. That person can tell you whether the gate motor is dead or just the battery inside the operator. If the gate is stuck open and your dog is loose, you don’t want a menu system. You want someone who says, “I’ll be there myself, or you can drive to the shop and look me in the eye.” We have been owner-operated since 2001, our address is published, and our license is real and checkable. Nobody in Whitney has to trust an anonymous dispatcher with a rented van and a sales pitch.
Our Gate Parts & Welding Services in Whitney
Hinge Replacement
Whitney’s 1980s and 1990s iron gates were often hung with lag-bolt hinges driven straight into CMU block mortar. Three decades of thermal cycling and wind load shears those lags, and one morning the gate leaf drops onto the driveway with a bang. We replace those hinges with through-bolted or embedded plate anchors that hold in the block itself, not the crumbling mortar. In Whitney, hinge replacement is the most common repair we do, and it is almost always cheaper than a new gate. A gate sags in the hinge post, not in the middle, and that is where we start.
Post Replacement
Caliche soil in Whitney is alkaline, hard, and reactive. It pushes and corrodes. A steel post set direct in that dirt will rust through below grade within 15 to 25 years, and the whole gate leans. When our crew works around the Whitney Mesa area, we almost never pull a post that is still solid. We set new posts deeper, weld proper base plates, and backfill in a way that moves with the soil instead of fighting it. Post replacement here is not just digging a hole. It is knowing what the caliche is going to do to that metal for the next three decades.
Rail Repair
Rails crack at the welds. That is a fact of south Nevada desert life. A hundred and ten degree afternoon, then a forty-five degree night, every single day for thirty years. The steel expands and contracts until a weld gives, usually at the hinge side or the top rail junction. We repair the rail in place, true the panel with a level, and weld only where the frame needs it. Fix the panel without the post and you’ll fix it twice.
Custom Welding
Not every Whitney gate issue is a broken part. Some gates were built wrong from the start, welded too light for their leaf weight, hung without adjustment screws, built before modern safety edges existed. Our custom welding service covers gate frame reinforcement, motor mounting plates, cantilever rebuilds, and gate hardware modifications. If a gate was welded by somebody who should have known better, Hal will say so plainly. Then he will show you how to fix it so it lasts.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Whitney
We service and stock parts for the gate operators Whitney homeowners actually have bolted to their block walls: LiftMaster, FAAC, BFT, Linear, Viking, and four other major brands. That matters because a FAAC unit from 2003 is not the same machine as a BFT from 2019, and guessing is expensive. We keep common control boards, capacitors, receivers, and limit switches on the truck when we roll into Whitney, which means a dead opener on a Monday often works by Monday afternoon. If the part is not on the truck, we know exactly where to get it and what it should cost.
Common Gate Parts & Welding Problems We See in Whitney Homes
If you live in the 89122 ZIP, here is what your gate is up against:
- Sheared lag-bolt hinges in CMU block. The 1980s-era iron gates were hung light, with hinge lags that rust and loosen inside the mortar joints. Over near the flat streets around Whitney Mesa, we regularly find two or three sheared lags per hinge, with the gate hanging by the top hinge only.
- Weld cracks at the hinge post connection. Daily temperature swings from 110°F afternoons to 40°F desert nights fatigue the metal right where the panel pivots. The crack is always worse on the south-facing side of the gate, where the UV hits hardest.
- UV-brittled operator seals on legacy openers. The intense sun out here kills rubber seals, bumper stops, and powder coat in a few years. A 1990s gate operator with dried-out seals lets dust and hard mineral water inside, and the limit switches corrode until the gate closes on your car.
- Corroded ferrous hardware from hard water. Whitney sits on mineral-laden water that is hard on every exposed bolt, screw, and ground lug. Latch strikes, post plates, and hinge pins all get slower and rougher until something finally snaps or jams.
Pricing for Gate Parts & Welding in Whitney, NV
A typical hinge replacement on a Whitney steel gate runs $180 to $380, depending on whether we are anchoring into solid block or rebuilding the mortared edge first. A full hinge post replacement generally runs $350 to $750, including concrete work above the caliche line. Custom welding repairs on a cracked rail or a torn panel run $150 to $600, depending on the length of the weld and whether the gate needs trueing afterward. A complete gate operator replacement, parts and labor, typically starts around $900 and goes up with the weight of your gate.
You get the price before the first weld arc. We don’t quote one number on the phone and hand you a different invoice when the gate is back on its hinges. No trip charge inside Clark County, $40 off any repair over $200, and a permanent 10% discount for seniors and veterans. If another company gave you a written estimate, bring it. We’ll give you a free second opinion, honest.
But the biggest cost factor in Whitney is the one nobody sees: the condition of the post. We will tell you if the post needs replacing before we start, and we will show you why. Quoted and agreed. Then we start.
We Also Serve Cities Near Whitney
Our crews run from Whitney to the surrounding Clark County communities daily. If you are in Whitney, you can read more about how we work right in your neighborhood. We also take calls from homeowners in Paradise, Winchester, Las Vegas, and Sunrise Manor. The phone number is the same: (877) 610-2993.
Serving Whitney, NV - Our Local Coverage Area
We’re based in the Whitney area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Whitney
In Whitney, you need a permit through the Clark County Building Department for certain automatic gate operator replacements, not the City of Las Vegas. Whitney is unincorporated Clark County, and that jurisdiction detail trips up out-of-area contractors every week. Our crew at Gatewood Fence & Gate handles the Clark County permit process for the 89122 ZIP on a regular basis. We will tell you if your specific job needs a permit, what it costs, and how long it takes. Call (877) 610-2993 and we will walk you through it.
Sometimes yes, sometimes no. If the gate leaf is out of square and the post is still solid in the block, we can cut and re-weld the frame, true it, and re-hang. But if the hinge post is corroded at the base or the lag anchors have stripped the mortar, welding the panel alone will not fix the sag. That gate will be on the ground again within a season. We always inspect the post first and tell you plainly whether the weld will hold or the post has to go.
If your Whitney home still has its original 1990s-era gate opener, it likely has no photo eye sensor, no reversing edge, and no force cutoff. That is dangerous, especially if children or animals live in the house. We inspect all safety devices when we service any automatic gate in the 89122 ZIP, and we can retrofit a modern edge sensor and entrapment protection onto your existing operator without replacing the whole unit in many cases. Ask us to look at it. We will show you exactly what is missing.
Yes. Whitney sits on caliche, that whitish, mineral-packed layer under the topsoil, and it is chemically aggressive to untreated steel. It eats post bases from the outside in, especially where the concrete ends and the metal goes into the ground. We replace Whitney posts more often than posts anywhere else in the valley we work. Our fix is a deeper hole, a proper base plate, and often a galvanized or stainless stub where the old one rotted.
Many times the rack itself has worn in one section, or the gate wheels have collapsed enough to let the pinion climb off the teeth. We can weld in a new rack section, re-shim the wheels, and reset the pinion engagement without replacing the whole rolling assembly. If the gate motor has stripped gears from years of jumping, a replacement is often cheaper than repeated repairs. We will inspect the whole track and tell you which fix is the cheaper one for your Whitney gate. Call (877) 610-2993 for an exact quote. Estimates are free.
Need gate parts or welding in Whitney? Call Gatewood Fence & Gate at (877) 610-2993 and a live person answers, 24/7. Free estimates, upfront pricing, and a 90-Day Done Right Promise on every job. If it’s not done right, we make it right.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Whitney and Clark County since 2001.