Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Access Control Across Whitney
Gate access control in Whitney, NV typically costs $450 to $2,800 depending on whether we’re adding a keypad, swapping a phone-entry system for a video intercom, or rebuilding a shared driveway setup, and most jobs here are done in a single visit. We work this side of the valley every week, so we know what the 89122 ZIP throws at gate hardware. If you’re in Whitney and your keypad quit or your swing gate binds at the latch, call (877) 610-2993 and a live person picks up, any hour.
Why Gatewood Fence & Gate Is Whitney’s Preferred Gate Access Control Company
Hal Gatewood started this shop in 2001 and his name is on every invoice. That matters in Whitney, where plenty of homeowners have already been through a national outfit that quoted one thing on the phone and handed them another number at the door. We don’t work that way. The price gets quoted and agreed before any work starts, in writing, and it doesn’t change when we show up.
We’ve pulled permits through the Clark County Building Department for gate work in Whitney more times than we can count. That’s not a small detail. Whitney is unincorporated Clark County, so when an automatic operator replacement needs new safety photocells or a loop detector, the rules are Clark County’s, not the City of Las Vegas. Homeowners who’ve never had to think about it get surprised. Out-of-area installers get it wrong. We don’t, because we live with it every week.
Every job carries our 90-Day Done Right Promise: if it’s not done right, we come back and make it right. One call brings Hal back, no runaround. And when you call, the person who answers is here, not a call center three states away.
Our Gate Access Control Services in Whitney
Most Whitney homes were built between 1975 and 2000, and the gate hardware from that era has hit or passed its service life. Here’s what we handle most often.
Keypad Entry
A wired or wireless keypad on a Whitney driveway gate runs $380 to $850 installed, depending on whether we’re adding one to an existing operator or replacing a dead unit. The keypads we install are sealed against the fine alkaline dust that blows through the east valley and rated for the UV load that cooks plastic faceplates within a few summers. We wire them to your existing operator and program the codes on site, then watch you test it before we leave.
Remote Control
Replacing a failed receiver or cloning remotes for a Whitney gate runs $180 to $400 for most systems. If your gate only opens when you hold the remote against the antenna, the receiver board is likely cooked from 110°F-plus thermal cycling. We stock receivers and remotes for FAAC, BFT, Linear, and Viking operators, so we usually fix that the same day without ordering parts that sit in a warehouse.
Phone Entry
Phone-entry systems for Whitney gates run $600 to $1,600 for a reliable unit installed and programmed. Hard, mineral-laden Whitney water is hard on the solenoids and relays in these systems, especially when they’re mounted on a south-facing block wall with no shade. We position enclosures to breathe, seal the wiring entries, and test call-forwarding through both your cell and landline before we pack up.
Card Reader
A card reader add-on for a Whitney community or shared driveway gate runs $500 to $1,200 installed, plus the cards or fobs themselves. We wire readers to the operator’s open input, set the latching logic for the gate’s swing or slide direction, and make sure the reader doesn’t fight the loop detector when a car pulls up. Clark County requires entrapment protection on any automated gate, and we bring older setups into compliance while we’re in there.
This is a slice of our full Gate Access Control work, and most Whitney jobs combine two or three of these at once.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Whitney
We service and install FAAC, BFT, Linear, and Viking operators on Whitney gates, among others. We keep the common receiver boards, limit switches, keypad overlays, and photocells for these brands in our service truck, not in a catalog. That means when a Viking swing arm strips under the sun’s heat or a BFT control board throws a memory fault, we can usually pull the part from the truck and finish the repair the same day instead of scheduling a second trip.
Common Gate Access Control Problems We See in Whitney Homes
- Swing gate binds at the latch but the keypad still shows an open signal. The alkaline caliche soil under Whitney heaves with moisture swings, and lag-bolt hinges set into CMU block mortar crack over time. The gate sags just enough that the latch sits proud, and the control board reads the limit switch as still tripped.
- Photocells misaligned every few weeks. A gate that creeps out of square from soil heave or hinge post wear pushes the safety beam out of alignment, and the operator refuses to close. Re-aiming the photo eyes helps for a week, but unless the post is fixed, you’ll chase it forever.
- Slide gate rack welds fatiguing. Whitney’s 110°F days and cool desert nights expand and contract steel constantly. Rack and pinion welds on older slide gates work-harden and crack, and the access controller can’t finish an open cycle because the gate shudders to a stop on the broken tooth.
- Access keypad keys stopped responding in heat. Membrane keypads and touchscreens with direct afternoon sun exposure degrade fast in Whitney. The UV breaks down the overlay, dust works into the switch contacts, and buttons register double or not at all. We replace them with metal-faced or shielded units designed for desert exposure.
Pricing for Gate Access Control in Whitney, NV
A keypad replacement in Whitney typically runs $380 to $850. A remote receiver swap runs $180 to $400. Phone entry runs $600 to $1,600. A full video intercom install with a mobile app runs $1,400 to $2,800. Adding safety photocells to an older Whitney gate runs $250 to $500 per pair installed. Labor rates here don’t differ much from the rest of the valley, but Clark County permit fees for operator and entrapment-safety work add $100 to $300 to any permitted job. You get the exact number in writing before we touch anything, and we offer $40 off any repair over $200, with a free second opinion on any written estimate. Seniors and veterans get 10% off every job, permanently. Call (877) 610-2993 for a free estimate.
We Also Serve Cities Near Whitney
If you’re reading this from over the line, we cover the whole east side of the valley. That includes Whitney, Paradise, Winchester, Las Vegas, and Sunrise Manor. Same crews, same warranty, same live person on the phone no matter which ZIP you’re in.
Serving Whitney, NV - Our Local Coverage Area
We’re based in the Whitney area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Access Control in Whitney
Whitney is unincorporated Clark County, so automatic gate operator replacements and any wiring tied to entrapment protection fall under the Clark County Building Department’s permitting authority, not Las Vegas city rules. If you’re adding new safety photocells or a loop detector to a Whitney gate, the county wants to see the installation pass an entrapment check. We pull that permit for you and handle the inspection. Call (877) 610-2993 and we’ll tell you exactly what your gate needs before anyone starts work.
Yes. On a shared driveway just off Nellis Boulevard in the 89122 ZIP, we rebuilt a sagging swing gate by replacing a rotted lag-bolt hinge post in the CMU wall, then mounted a new LiftMaster operator with a safety photocell and keypad entry wired to the existing loop detector so both vehicles and pedestrians kept flowing during the repair. We stage the work so the gate never stays down longer than it has to, and we tell everyone on the shared easement what’s happening before we start.
Your hinge post has likely shifted. Caliche soil under Whitney heaves with moisture, and lag-bolt hinges set into CMU block mortar crack over time, dropping the gate leaf so the latch binds and the limit switch reads open when it isn’t. The fix is to rebuild the hinge post, not to just re-shim the latch. Call (877) 610-2993 and we’ll come look at the post, not just the latch.
Solar works in Whitney if the panel gets direct sun most of the day, which most east-valley yards do. A solar operator with battery backup runs $900 to $1,800 installed, and we size the panel and battery to the gate’s open-cycle count, not to the cheapest kit on the shelf. Whitney’s UV load degrades solar panel frames and battery housings faster than most places, so we spec metal housings and vented battery boxes from the start.
Entrapment protection is the safety system that stops or reverses a gate if a person, car, or pet is in its path, and it’s required by Clark County code on any automated gate. Most Whitney gates from the 1980s and 1990s have no photocells or a dead set, which means the gate will keep pushing if something gets caught. Adding photocells and a compliant control board runs $500 to $900 on a typical Whitney swing gate, and it’s the first thing we check on any call. Call (877) 610-2993 for a free safety check on your gate.
If your access control has quit, or the gate only opens when it feels like it, call us at (877) 610-2993. A live person answers. We’ll give you a straight answer, a written price, and a 90-day promise that stands up. The name is on the shop, and the shop is down the road.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Whitney since 2001.