Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Roanoke
Most gate installation in Roanoke repair calls we get in the 76262 and 76299 zip codes aren’t electrical problems at all. The gate motor sounds fine, the board looks fine, but the gate binds mid-swing and trips the overload. That’s almost always a hinge post that has tipped 2 or 3 degrees from North Texas clay movement, and it needs a welder who understands soil, not just a parts swapper. Hal Gatewood has been fixing gates like this since 2001, and he’ll tell you the same thing he tells every Roanoke homeowner: fix the post, not just the panel, or you’ll fix it twice. Call (877) 610-2993 and you’ll get a live person who can talk through what you’re seeing.
Why Gatewood Fence & Gate Is Roanoke’s Preferred Gate Parts & Welding Company
Roanoke sits on Blackland Prairie clay that swells after spring rains and shrinks through 100-degree summer stretches. Gates here don’t just wear out. They get pushed out of square. The subdivisions off Pearson Lane and Byron Nelson Parkway were built fast between 2000 and 2023, and a lot of those ornamental iron driveway gates went in with post footings that sit right in the active clay line. When the soil moves, the post goes with it, the hinge plate torques, and the gate starts fighting itself. We see it every week. Our Gate Parts & Welding team cuts the old hinge mount, re-welds it at the corrected angle, and sets new footings below the movement zone so the repair holds.
Roanoke residents call us because we answer the phone with a person, not a voicemail tree. Hal’s name is on the shop and on every invoice. If a weld cracks or a roller binds within 90 days, one call brings him back. No runaround. We serve all of Gate Parts & Welding in Roanoke with on-site welding, so your gate never leaves your driveway on a flatbed. We also carry parts for the brands most common in this area, which keeps most repairs to a single visit.
Our Gate Parts & Welding Services in Roanoke
We focus on the mechanical work that keeps a heavy custom gate swinging true: hinge replacement, post replacement, rail repair, and custom welding. When you call, we’ll talk through what the gate is doing and schedule a time that works for you. If repair is possible, that’s what we recommend. We don’t swap parts that don’t need swapping.
Hinge Replacement
Hinge replacement in Roanoke usually starts with a simple question: is the post still plumb? Around here, the answer is often no. Blackland clay pushes posts up and down over an inch per year, and a hinge that looked fine at install is now carrying the gate at an angle. We replace worn hinge pins, re-weld hinge plates, and shim or re-seat the gate leaf so it swings without scraping the ground or binding at the middle.
Post Replacement
Clay heave is the single biggest reason we replace gate posts in 76262. A post tipped just 2 degrees can bind a twelve-foot ornamental leaf and trip the operator’s overload sensor every afternoon. We cut out the old post, pour a new footing below the active clay line, and set the replacement post plumb. Then we re-hang the gate and recalibrate the opener. That’s the order that actually fixes it. Replacing a post without addressing the soil depth just guarantees the same problem returns next season.
Rail Repair
Rails on Roanoke gates take a beating from heat, ice, and the constant flexing of a gate that’s fighting its own hardware. We straighten and re-weld bent rails, splice rotted or cracked sections, and reinforce corners that show fatigue. The goal is to keep the original look of the gate intact. Most ornamental iron in this area is custom or semi-custom, and you don’t want a patch that looks like a patch.
Custom Welding
Custom welding is where we spend a good chunk of our time in Roanoke. The estate properties off Pearson Lane and the newer custom builds along the 114 corridor have gates that were fabricated to match the house. When a section rusts through or a hinge mount tears loose, you can’t just order a replacement panel from a catalog. We fabricate and weld on site, matching the picket profile, the scrollwork, and the finish as closely as the material allows. For heavier repairs, we can powder coat or prime and paint to blend the repair into the existing gate.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Roanoke
We work on gates built around FAAC, BFT, Linear, and Viking hardware, among others. A lot of the original-install operators in Roanoke subdivisions from the mid-2000s were Linear and LiftMaster units, and those are reaching the end of their service life in clusters now. We keep common Linear swing operator boards, FAAC limit switches, and BFT gear kits on the truck, which means we’re not waiting on a parts shipment when your gate is stuck open at night. If the operator is still good and the problem is mechanical, we say so. We’d rather replace a hinge than sell you a Roanoke gate motor & opener you don’t need.
Common Gate Parts & Welding Problems We See in Roanoke Homes
Roanoke’s soil and weather create a specific set of gate failures. Here’s what we see most:
- Clay-heave hinge post binding: The post tips 2 to 3 degrees over a season or two, the gate leaf binds mid-swing, and the operator’s overload shutoff trips. The motor sounds fine because it isn’t the motor. This is the most common repair call in 76262, and it requires welding the hinge mount at the corrected angle, not just adjusting the opener.
- Original operators failing in waves: Subdivisions built between 2000 and 2012 all used similar Linear, LiftMaster, or US Automatic openers. Twenty years later, those units are reaching end-of-life at the same time across whole streets. We replace operators or swap boards and limit switches as needed, always pairing the new unit to the gate’s actual weight and swing.
- Freeze damage to exposed mechanisms: Winter ice events aren’t common in Denton/Tarrant County, but when they hit, exposed gate operators and latch mechanisms without proper weather sealing crack or stick. We see frozen gearboxes and stuck lock bolts every January in Roanoke.
- Rusted hinge plates and welds: Blackland clay holds moisture against the bottom of gate posts, and the hinge plate mount is often the first place rust shows up. We cut out the rusted section, weld in a new plate, and seal it so the repair doesn’t become a new failure point.
Pricing for Gate Parts & Welding in Roanoke, TX
We quote the price before any work starts, and that’s the price you pay. Hinge replacement in Roanoke typically runs $180 to $340 depending on the hinge size, gate weight, and whether we’re re-welding the mount. Post replacement ranges from $450 to $900, including the new footing poured below the clay line. Custom welding jobs run $150 to $650, depending on the extent of the fabrication and finish work needed. Rail repair and straightening usually lands between $150 and $400. These are honest numbers for the Roanoke market. We don’t pad them because you live in a nice neighborhood.
Every quote is in writing before we start. We offer $40 off any repair over $200, no trip charge inside the county, and a free second opinion on any written estimate you’ve received. Seniors and veterans get 10% off, always. Call (877) 610-2993 to schedule a time for us to look at your gate.
We Also Serve Cities Near Roanoke
Our crews work throughout the Alliance corridor, not just inside Roanoke city limits. If you’re in Trophy Club, Southlake, Keller, or Lantana, the same team that handles Roanoke gates can help you. Dispatch and scheduling are coordinated from our Dallas-Fort Worth office, and the crew arrives with the truck stocked for the repair.
Serving Roanoke, TX - Our Local Coverage Area
We’re based in the Roanoke area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Roanoke
Because the motor is fine. Roanoke’s Blackland Prairie clay cycles the gate post up and down more than an inch per year, gradually tipping it 2 or 3 degrees out of plumb. That tips the hinge plate, which binds the leaf mid-swing, which trips the operator’s overload shutoff. The fix is re-welding the hinge mount at the corrected angle and, in many cases, setting the post deeper. Call (877) 610-2993 and we’ll diagnose it on site.
Yes, in most cases. If the post itself is structurally sound and only the hinge plate has torqued or torn, we cut off the old mount, grind the post clean, and weld a new hinge plate at the angle the gate needs. If the post has moved, we realign it or replace it first. The weld is only as good as the post underneath it, so we check the post before we burn.
No, not necessarily. The overload sensor is doing its job: telling you the gate is fighting resistance it shouldn’t be. In Roanoke, that resistance is usually a hinge post that has heaved out of line, not a bad motor or board. We check the post, the hinges, and the gate’s swing geometry before we recommend touching the gate access control in Roanoke operator. If the operator does need replacement, we’ll show you the test results and give you a written price first.
MIG welding with proper surface prep works well for most ornamental iron repairs, and that’s what we use on site for hinge mounts, rail splices, and scrollwork. The bigger issue in Roanoke is the footing under the post, not the weld itself. A perfect weld on a post that keeps moving will crack again. We set the post below the active clay line before we weld, so the repair isn’t fighting the same forces that broke it the first time. Call (877) 610-2993 for a free estimate on custom iron work.
Yes, within reason. We match picket profiles, spacing, scroll patterns, and overall height as closely as the available material allows. For gates built in the last 20 years by local fabricators, we can usually come extremely close. For older or very unusual iron work, we’ll fabricate a section that matches the gate’s proportions and profile, then finish it to blend. We won’t promise an invisible repair unless it’s achievable, and we’ll always show you a photo of similar work we’ve done in Roanoke before starting.
If your gate is binding, sagging, or tripping the overload in Roanoke, call (877) 610-2993. We’ll talk through what it’s doing, set a time to look at it, and quote the repair before we touch anything. Hal Gatewood’s name is on the invoice, and he stands behind every weld.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Roanoke since 2001.