Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Access Control Across Roanoke
Gate access control in Roanoke comes down to three things: a solid post, a clean power run, and an operator that isn’t fighting the soil. Most failed keypads and remotes in the 76262 ZIP aren’t actually broken. They’re wired to a gate leaf that can’t swing because the hinge post has moved. We fix that at the post, not at the circuit board. If you’re off Byron Nelson Parkway or Pearson Lane and your gate won’t respond, call (877) 610-2993 and we’ll get someone out to look at it.
Why Gatewood Fence & Gate Is Roanoke’s Preferred Gate Access Control Company
Hal Gatewood has been fixing gates since 2001, and the shop’s name is on every invoice. That matters when you live in Roanoke, where half the automated gates in Fairway Ranch and Woodland Hills were installed by builders who handed the keys over and never came back. We see the same operators day after day: LiftMaster LA400s on their last leg, Linear actuators with stripped limit cams, keypads with cracked housings from the last ice storm. When we tell a Roanoke homeowner what’s wrong, we’re describing the third or fourth gate we’ve seen with that exact problem that month.
Our customers in Roanoke know the 90-Day Done Right Promise isn’t a slogan. It’s printed on the work order. If the gate binds again, one call brings us back. We also answer the phone with a live person, 24/7. Not a recording, not a call center three states away. When you call (877) 610-2993 at 10 p.m. because your gate won’t close and your dog is eyeing the street, you get a person who knows Roanoke streets well enough to say “I’ll be there in a half hour” and mean it.
We’re not based across the country. Scheduling is coordinated from our Dallas-Fort Worth office, and crews work Roanoke daily. We know the neighborhoods, the builders, and which year’s housing wave your gate came out of just by the operator model. That’s the kind of local knowledge you can’t fake from a call center.
Our Gate Access Control Services in Roanoke
We handle the full range of Gate Access Control work, from simple keypad swaps to full smart access retrofits on existing ornamental iron gates. Here’s what Roanoke homeowners call us for most often.
Keypad Entry
A keypad should work every time, rain or shine, 105°F or 18°F. In Roanoke, keypads fail for two reasons: cracked housings from winter freezes, and wiring that’s been chewed or shorted by a post that shifted and pulled the low-voltage line tight. We install weather-sealed keypads rated for North Texas summers, and we re-route or re-run the wiring so it isn’t in tension. We also reprogram existing keypads when they’ve lost their codes or when a new homeowner takes over and doesn’t have the builder’s pin.
Remote Control
Remote controls aren’t complicated, but they depend on a receiver that’s getting clean power and a gate leaf that swings freely. If your remote works some days and not others, especially after rain, the problem is usually a binding hinge post or a receiver antenna that’s been knocked loose. We diagnose the operator’s radio receiver, test the range from the actual driveway, and replace remotes only when the remote is genuinely dead. For Roanoke’s newer subdivisions around Lantana’s edge, we also see a lot of builder remotes that were never programmed correctly to begin with.
Phone Entry
Phone entry systems let you buzz visitors through from your cell, whether you’re in the kitchen or stuck at DFW. For Roanoke homes with long driveways and ornamental gates up at the street, we tie the phone entry module into your existing operator so you can open the gate from anywhere with cell service. This is a popular add-on for homeowners who converted manual gates to automatic and didn’t realize a phone entry option existed at the time.
Card Reader
Card readers and fob systems show up more on shared drives and small HOA entries in Roanoke’s newer gated pockets. We install and service card readers from brands we already stock, including BFT and Linear, and we make sure the reader is sealed against the dust and grime that blow through when the winds kick up off the plains. A sticky card reader at an HOA gate is a security issue, not a convenience problem. We treat it that way.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Roanoke
We’re certified to service nine major gate brands, and for Roanoke work we most often see FAAC, BFT, Linear, and Viking operators on the gates that come through our shop. We stock common replacement parts for these locally, which means we don’t have to order a limit switch from California while your gate sits half-open for a week. When your Viking operator needs a new control board or your FAAC hydraulic arm is seeping, we typically have the part on the truck or can get it same-week without holding you hostage. Hal fixes what’s fixable. If the part is genuinely shot, we tell you that too, and we show you the failed component before we replace it.
Common Gate Access Control Problems We See in Roanoke Homes
Roanoke’s houses are newer than most of North Texas. That sounds like it should mean fewer problems. In practice, it means a different set of problems, all hitting at once. Here’s what we see week after week:
- Gate leaf binds mid-swing from clay-heaved hinge posts. The Blackland Prairie clay under Roanoke swells after spring rain and shrinks in the 100°F summer dry spells. That cycles gate posts up and down an inch or more per year. A post tipped 2-3 degrees outward binds the leaf at the sag point, and the operator’s overload shutoff makes a perfectly good keypad or remote seem dead.
- Builder-grade operators reach end-of-life simultaneously. Homes built in the 2000-2015 wave around Roanoke mostly came with LiftMaster LA400 or Linear swing operators that were adequate for the price but were never meant to last forever. One faulty access device on a 2010 gate is often a sign the entire opener is on borrowed time. We’d rather tell you that on our first visit than replace a keypad in March and a motor in June.
- Exposed keypad housings and card readers crack in winter freezes. Roanoke’s ice events aren’t Montana cold, but they’re enough to split a plastic keypad cover and let moisture wick into the circuit board. Even a hairline crack kills a keypad by March. We replace builder keypads with sealed, gasketed units and hit the seam with dielectric grease before closing up.
- Low-voltage wiring gets pulled tight by moving posts. When a post shifts, the wire running to your keypad, photo-eyes, or loop detector tightens, stretches, and eventually shears inside the insulation. The gate works intermittently, then quits. The fix is re-running the wire with slack and often resetting the post. Patience and a voltmeter beat guesswork here.
Pricing for Gate Access Control in Roanoke, TX
Access control work in Roanoke runs a wide range because one call is a keypad replacement and the next is a full smart access retrofit on a dual-swing gate with a power run that should have gone in during construction and didn’t. A standard sealed keypad replacement in Roanoke runs $180-$350 installed. Adding a single remote or reprogramming an existing one runs $50-$120. A phone entry module with installation typically runs $450-$850 depending on whether your operator already has a compatible connection. A full smart access setup on an existing gate, including new keypad, phone entry, and two remotes, runs $1,200-$2,200. Video intercom runs higher, usually $1,800-$3,500 with the monitor and camera.
You’ll always know the price before we start. The quote is written and agreed before any work begins. Estimates are free. Call (877) 610-2993 and we’ll come out, look at your gate, and tell you what it costs to fix. No trip charge inside the county.
We Also Serve Cities Near Roanoke
Our crews cover Roanoke and the surrounding communities daily. That includes Trophy Club, Southlake, Keller, and Lantana. If you’re just over the city line, we still answer the phone the same way, and we still show up with parts on the truck.
Serving Roanoke, TX - Our Local Coverage Area
We’re based in the Roanoke area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Access Control in Roanoke
The keypad is working. Your gate leaf is binding on a hinge post that has tipped from clay heave. Roanoke sits on Blackland Prairie clay that swells and shrinks with the seasons, and over two or three years that’s enough to move a post 2-3 degrees and trip the operator’s overload. You don’t need a new keypad. You need the post reset and the hinge plate re-welded. We do that on-site without hauling your gate off. Call (877) 610-2993 and we’ll come look at the post, not the keypad.
Yes, in most cases. A 2012 LiftMaster swing operator is old enough that we’ll inspect it first, because the smart access module is only as good as the operator it’s talking to. If the motor and limit switches are still healthy, we can add a smart module and keypad without touching the rest of the system. If the operator is on its way out, we’ll tell you that plainly and give you a written price for the full conversion before anything gets ordered.
Yes. Roanoke gets hard enough freezes that unsealed builder keypads and card readers crack. Once the housing cracks, moisture gets inside and the board shorts by spring. We install sealed, gasketed keypads and typically apply dielectric grease at the seams. If your existing keypad has already cracked, get it swapped before the next rain, not after the gate quits. Same-day replacement is usually possible. Call (877) 610-2993 for a quick check.
That’s usually a chain that’s jumped the sprocket, a gear that’s stripped, or a wheel carriage bound on a track that’s shifted with the clay. Roanoke’s soil movement messes with slide gates differently than swing gates: the track settles unevenly and the gate drags, which strips the drive gear or throws the chain. We can tell you which it is in about ten minutes on-site. If it’s the gear, we replace it. If it’s the track, we re-bed it and adjust the wheels. Either way, you’ll know the price before we start.
Yes, and this is exactly the kind of add-on that Roanoke’s newer homes should have been built with but usually weren’t. We run the conduit and power, set the operator, mount the keypad and phone entry module, and tie the photo-eyes and safety edges into the operator’s entrapment circuit. It’s a measured job, not an emergency call, so we come out first, take measurements, and hand you a written price before any equipment gets ordered.
If your gate access control is acting up in Roanoke, call (877) 610-2993. Hal’s name is on the shop, and the shop is down the road. That’s the oldest accountability there is.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Roanoke and the surrounding North Texas communities since 2001.