Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Roanoke
Gate installation in Roanoke runs $1,800 to $9,500 for a typical ornamental iron driveway gate, with custom double swing gates on the high end and simpler pedestrian gates on the low end. Most jobs take one to two days on site, and we quote the full price before any work starts. Hal Gatewood has been installing and welding gates since 2001, and the crew that shows up in Roanoke is the same crew that will come back if anything’s not right. Call (877) 610-2993 and you’ll get a live person, not a queue.
Why Gatewood Fence & Gate Is Roanoke’s Preferred Gate Installation Company
Roanoke’s subdivisions off Pearson Lane, Byron Nelson Parkway, and along the 114/170 corridor are full of custom homes where the gate isn’t an afterthought. It’s the first thing you see pulling in. Hal’s name is on the shop and on every invoice, and he has been at this since 2001, long enough to know what a gate in 76262 actually goes through. The Blackland Prairie clay under these newer subdivisions swells and shrinks with every season, and a gate installed with shallow footings will tip within a few years. That’s the kind of thing you only learn by doing this work in Roanoke, not by reading a spec sheet.
We answer the phone around the clock. A live person, every time. When you call about a gate that won’t close or an operator that trips, you talk to someone who knows the difference between a hinge post problem and a motor problem. Our Gate Installation team works in Roanoke, Trophy Club, and the surrounding area regularly, and we keep parts for the brands these homes were built with: FAAC, Linear, LiftMaster, US Automatic. The 90-Day Done Right Promise is in writing on every job, and yes, it’s exactly what it sounds like. If it’s not done right, one call brings Hal back.
Our Gate Installation Services in Roanoke
Driveway Gate
A driveway gate in Roanoke is usually ornamental iron, often automated, and often heavy. The engineering question here isn’t the gate leaf. It’s the post footing. Roanoke’s expansive clay demands over-excavated footings and steel-reinforced concrete collars, or the post tips 2 to 3 degrees within a season or two and the gate binds mid-swing. We set every driveway gate post deeper than the frost line and wider than the manufacturer’s minimum, because the clay doesn’t care what the manual says.
Swing Gate
Single and double swing gates are the most common install in Roanoke’s 76262 subdivisions. The clay-heave cycle is the recurring villain here. When the soil swells in spring and shrinks in the hundred-degree summer dry spells, a shallow-set hinge post moves. Then the leaf drags, the operator overloads, and the homeowner assumes the motor is dead. Our crews re-set posts in steel-reinforced footings and re-hang the leaves so they run true through the next wet-dry cycle. It’s not a patch job; it’s how it should have been done the first time.
Sliding Gate
Sliding gates can work on Roanoke’s clay, but the track and the post that anchors the operator need special attention. Clay heave will lift a shallow concrete track run and snap an under-rated gear rack. We over-excavate the track bed, pour a deeper reinforced pad than standard, and anchor the operator post the same way we anchor a swing gate post. On sloped lots, which Roanoke has plenty of, we set the track on a stepped footer rather than floating it on fill.
Double Gate
A custom double swing gate is a matched pair of heavy leaves that have to meet in the middle, latch cleanly, and hold their alignment for years. On Roanoke’s clay, that means both hinge posts get the same over-excavated, steel-reinforced treatment, and the center drop rod gets a socket that won’t heave out of place. Our crew pulled up to a home off Pearson Lane where a new double gate was binding. The owner thought the LiftMaster operator was failing. The real story: the hinge post had tipped two degrees from one wet-dry cycle and stressed the weld at the hinge plate mount. We cut the post free, set it deeper, re-hung the leaves, and recalibrated. That gate runs silent now.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Roanoke
We install and service FAAC, BFT, Linear, and Viking operators, among others, and we carry parts for LiftMaster and US Automatic because that’s what the early-2000s subdivisions in Roanoke were built with. When an entire street’s original operators reach end-of-life around the same time, having a local crew that stocks the parts beats waiting on a backorder. We weld on site, in your driveway, so a gate doesn’t leave your property to get fixed.
Common Gate Installation Problems We See in Roanoke Homes
- Clay heave tips the hinge post. Roanoke sits on Blackland Prairie clay that swells in spring and shrinks in the dry Texas summer. A post set in a standard footing can move an inch or more in a year, binding the leaf and tripping the operator’s overload shutoff.
- Original-install operators failing in waves. The subdivisions built in the early 2000s used Linear, LiftMaster, and US Automatic operators. Those units are now reaching end-of-life at roughly the same time across whole neighborhoods, and a dead swing gate is the first sign.
- Weld stress at the hinge plate mount. We see this constantly in the newer subdivisions. The gate looks broken, the motor sounds fine, but the weld at the hinge plate has cracked from post movement. Fix the post first, then the weld, then the motor last.
- Shallow footings on heavy custom gates. A heavy ornamental double gate installed on a standard two-foot footing will settle unevenly on Roanoke’s clay. That leads to misaligned leaves, premature hinge pin wear, and an operator fighting harder than it should every cycle.
Pricing for Gate Installation in Roanoke, TX
Here’s what we see across Roanoke’s market. A single swing driveway gate with an operator typically runs $2,800 to $5,500 installed. A custom double swing ornamental iron gate runs $5,000 to $9,500, with the range driven by gate width, leaf weight, and the footing work the soil demands. A pedestrian gate runs $1,800 to $3,200. A sliding gate runs $3,500 to $7,000, depending on track length and operator duty cycle. Post footing over-excavation and steel-reinforced collars add cost but they are the difference between a gate that runs true for a decade and one that binds in two seasons. The price we quote is the price you pay, agreed before any work starts. Seniors and veterans get a permanent 10% discount. Call (877) 610-2993 for a free estimate.
We Also Serve Cities Near Roanoke
Our crews cover Roanoke and the surrounding communities, including Trophy Club, Southlake, Keller, and Lantana. If you’re in one of those cities and looking for Gate Installation in Roanoke-quality workmanship, we’re already working in your area and can schedule a measure without a trip charge inside the county.
Serving Roanoke, TX - Our Local Coverage Area
We’re based in the Roanoke area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Roanoke
Roanoke sits on Blackland Prairie expansive clay that swells dramatically in spring rains and shrinks and cracks during hundred-degree summer dry spells, cycling posts up and down an inch or more per year. Grapevine has more mixed soils, so the heave is less uniform. In Roanoke’s 76262 subdivisions, the entire subgrade is expansive clay, which means standard footings tip hinge posts within a few seasons. We over-excavate and pour steel-reinforced concrete collars so the post stays exactly where we put it. Call (877) 610-2993 for a free estimate on your gate project.
Sag on a double gate almost always traces back to the hinge post, not the leaves. On a sloped Roanoke lot, we set both hinge posts in over-excavated, steel-reinforced footings, use heavier hinge barrels than the gate manufacturer specs, and install a center drop rod socket that locks the leaves together when closed. Then we hang the leaves with a slight inward cant so they settle to true alignment as the hardware seats. Give us a call at (877) 610-2993 and we’ll walk your lot and write a job-specific price.
Yes, but the track bed and operator post need to be engineered for clay movement. A standard shallow track pad will lift and crack as the soil cycles through wet and dry seasons, and the gate will jam. We over-excavate the track run, pour a deeper reinforced pad, and anchor the operator post like a swing gate post. On steeper lots we step the footer so the track follows grade instead of floating on fill. Call (877) 610-2993 and we’ll give you a written price for a sliding gate that stays put.
Roanoke follows the same UL 325 standard as the rest of Texas: every automated gate needs at least two independent entrapment protection devices, typically photo eyes plus an edge sensor or an operator with built-in obstruction reversal. On a heavy custom gate, we also set the obstruction sensitivity correctly, because a gate that reverses too easily on a windy day is one that won’t fully close, and a gate that doesn’t reverse fast enough is a hazard. We install and verify all entrapment protection on every automated gate we put in. Call (877) 610-2993 for a free quote.
Because Roanoke’s clay has swelled and moved the hinge post, the gate leaf now binds mid-swing and the operator shuts down to protect itself. The motor isn’t failing; the post has tipped two or three degrees. We cut the post free, re-set it in a deeper steel-reinforced footing, re-hang the leaf, and recalibrate the operator. After that, the next rainstorm won’t throw it off. If you’re in Roanoke and your gate is tripping, call (877) 610-2993 and we’ll diagnose it same day.
Get Your Free Gate Installation Estimate in Roanoke
If you’re planning a new gate in Roanoke, or your current one is fighting the clay, call (877) 610-2993. You’ll talk to a live person who knows this area, knows these soils, and knows what it takes to keep a heavy ornamental gate running true. Hal’s name is on the shop and on every job, and the 90-Day Done Right Promise is in writing. We’ll come out, measure, and give you a written price before any work begins. No trip charge inside the county, and a free second opinion on any written estimate you already have.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Roanoke with gate installation and repair since 2001.