Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Motor & Opener Across Grapevine
Gate motor and opener service in Grapevine, TX typically costs $220 to $740 for repairs and $850 to $2,400 for a full operator replacement, and it’s work we handle same-day or next-day for most Grapevine homes. We know exactly which side of 114 you’re on, how the red clay behaves near Grapevine Lake, and why a slide gate on a shared driveway off Dove Loop behaves nothing like a swing gate on a half-acre lot in Whispering Hills.
Hal Gatewood has been fixing gates since 2001, and he built Gatewood Fence & Gate to serve the DFW metro the way a local shop should: a live person answers when you call (877) 610-2993, the price is quoted and agreed before any work starts, and every job carries the 90-Day Done Right Promise in writing. No dispatch queue. No call center. Just a locally owned, owner-operated gate company that shows up when we say we will.
Why Gatewood Fence & Gate Is Grapevine’s Preferred Gate Motor & Opener Company
Grapevine is a small city with very big gate demands. The resort corridor along SH-26 near DFW Airport runs commercial slide operators through more cycles in a week than most residential gates see in a year. Three miles west, the lakefront estates off Fairway Drive and Lakeside Drive sit on expansive black cotton clay that heaves hinge posts out of plumb every wet-dry cycle. Most gate companies treat those two jobs the same. They are not the same, and we do not treat them that way.
Our Gate Motor & Opener crew works Grapevine weekly. We know the older 1990s brick subdivisions around Cross Timbers Middle School where original Mighty Mule and LiftMaster operators are hitting the 20 to 30 year mark and circuit boards are starting to fail. We know the tighter shared driveways along Hall-Johnson Road where a swing gate simply will not fit and a slide motor becomes the only workable answer. And we know the commercial operators on the Gaylord Texan and Grapevine Mills side of town that need repair now, not next Thursday.
Hal’s name is on the shop and on every invoice. Our address is published. Our license number is published. The person who shows up to your Grapevine gate is trained on nine major brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. More important, the person who shows up knows he may see you at the hardware store next week. That’s the oldest accountability there is.
Our Gate Motor & Opener Services in Grapevine
Motor Repair
Most Grapevine gate motor failures are fixable without replacing the whole operator. We find stripped drive gears on high-cycle commercial slide gates along SH-26, blown capacitors on older residential swing operators in the 76051 corridor, and fried logic boards on units that took a North Texas lightning strike. Hal repairs in your driveway, welds on site if the bracket cracked, and does not haul your gate off to a shop across town. A typical gate motor repair in Grapevine runs $220 to $520 depending on the part and the operator brand.
Slide Motor Installation
Slide gates are the standard in Grapevine’s tighter residential developments and along commercial service lanes where a swing gate would block traffic or a neighbor’s access. We install and service slide motors from Linear, Viking, DoorKing, and BFT. We size the motor to the gate weight, not the other way around, which matters on heavy steel commercial gates off Grapevine Mills Parkway. A new slide motor installation for a standard residential slide gate in Grapevine typically runs $850 to $1,700.
Swing Gate Motor Installation
The lakefront estates around Grapevine Lake favor ornamental iron swing gates, and those need a motor sized for a heavy leaf on sometimes steep, uneven grade. We install swing operators with proper travel limits, current sensing, and safety photocells. We also account for the clay: a swing gate post that moves seasonally will bind a new operator within a year unless the footing is deep enough. We pour footings on 76051 and 76099 estates with rebar set below the active clay zone. New swing operator installation in Grapevine runs $900 to $2,400 for a residential double-leaf setup.
Swing Gate Motor Installation
If your Grapevine home has a courtyard gate or a wide driveway entrance with room to swing inward, a swing motor is often the quieter, lower-maintenance choice. We install FAAC and Ghost Controls swing arms on brick-pillared entries throughout Grapevine’s 1990s subdivisions, and the work almost always includes correcting post plumb first. Post moves, gate binds, motor overloads. Fix the post and the operator stops fighting itself. Most Grapevine swing motor installations include that alignment work as part of the quote.
Linear Motor Repair and Replacement
Linear-brand operators are common in Grapevine’s residential slide-gate stock, especially where builders installed the OSCO or Linear Pro series 20 odd years ago. We repair Linear logic boards, replace worn linear drive screws, and recalibrate travel limits. When a Linear motor is beyond saving, we offer a same-footprint replacement so your existing gate and track stay in place. Linear motor repair in Grapevine typically falls between $200 and $480.
Battery Backup
Grapevine sits in storm country. When a spring line of thunderstorms rolls through and takes out power for six hours, a gate without battery backup is either stuck closed or manually chained open, which means no security. We install battery backup modules on residential and commercial operators throughout Grapevine, sized for enough cycles to get a hotel loading-dock gate through an afternoon outage. Battery backup installation runs $350 to $800 including the unit and wiring.
Intercom Integration
Grapevine’s larger estate properties and small HOAs along the shore of Grapevine Lake use gate intercoms tied into the opener. We integrate new or existing intercom systems with slide and swing operators so the release relay fires cleanly. A Grapevine intercom-to-operator integration typically runs $250 to $600 depending on wiring and whether we need to pull new low-voltage cable.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Grapevine
We are certified to service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. The brands we carry local stock for in the Grapevine area include Linear, Viking, and DoorKing, because those three show up most often in residential slide gates, commercial service lanes, and the resort operators off SH-26. Stocking parts locally means a Tuesday repair is not waiting on a Friday parts shipment from Ohio. Our Grapevine customers do not pay the time toll of a parts delay when the fix is already on the truck.
Common Gate Motor & Opener Problems We See in Grapevine Homes
- Stripped rack and pinion gears on high-cycle slide gates. The commercial slide gates near Grapevine Mills and the Gaylord Texan cycle hundreds of times a day. The pinion gear eats the rack over time, especially if the gate was never greased. We replace both the rack section and the drive gear, not just one side of the wear pair.
- Post heave binding swing gates near Grapevine Lake. Expansive clay swells after rain and shrinks in drought, moving hinge posts a full inch or more out of plumb. The operator works harder, draws more amps, and eventually throws an overload fault or strips the drive train. We reset the post footing below the active clay zone before reinstalling the operator.
- Water and debris damage on compact slide operators in shared driveways. Grapevine’s tighter lots and shared rights of way push builders toward compact slide operators mounted low to the ground. Those pick up gravel, mud, and lawn clippings, and the lower control board is the first thing to corrode. We clean, reseal, and relocate boards upward where we can.
- Lightning-damaged control boards. North Texas thunderstorms hit flat, exposed Grapevine subdivisions hard. A nearby strike will fry a gate board through the low-voltage line even when the house TV survives. We replace boards and add surge protection on the operator feed, which most original installs never had.
Pricing for Gate Motor & Opener in Grapevine, TX
Here are honest ranges for what we charge in Grapevine. A motor repair typically runs $220 to $520. Slide motor installation runs $850 to $1,700 for residential, and more for heavy commercial operators. Swing operator installation runs $900 to $2,400 depending on gate weight and leaf count. Linear motor repair runs $200 to $480. Battery backup runs $350 to $800. Intercom integration runs $250 to $600. The price you are quoted is the price you pay, agreed before any work starts. No trip charge inside the county. We also offer $40 off any repair over $200, a free second opinion on any written estimate, and a permanent 10% discount for seniors and veterans. Call (877) 610-2993 for an exact quote, estimates are free.
We Also Serve Cities Near Grapevine
Gatewood Fence & Gate handles gate motor and opener repairs throughout the Grapevine area, including Southlake, Colleyville, Coppell, and Euless. Same local crew, same 90-Day Done Right Promise. We schedule from our Dallas-Fort Worth office, and the crew serving Grapevine is minutes away when Southlake or Coppell calls.
Serving Grapevine, TX - Our Local Coverage Area
We’re based in the Grapevine area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Motor & Opener in Grapevine
Because a commercial slide gate at a Grapevine Mills-area hotel can log more cycles in a week than a residential gate sees in a year. The operators on that corridor run thousands of open-close cycles weekly, which accelerates wear on drive motors, logic boards, and rack-and-pinion gear sets. We recently replaced a worn rack and pinion on a 24-foot slide gate at a property near Grapevine Mills where the DoorKing operator had logged over 300,000 cycles and the gears were stripped smooth. Residential parts are not built for that duty cycle. Commercial-rated parts are, and that is what we install. If your Grapevine business gate is failing twice a year, call (877) 610-2993 and we will tell you honestly whether it is the operator or the gear set.
Yes, if the property line and driveway length allow it. We have converted several Grapevine shared-driveway entries where a swing gate would arc across a neighbor’s parking area or into the alley. We install a cantilever or V-track slide setup with a Linear or Viking motor sized to the gate weight, run the low-voltage, and set the safety edges and photocells. A Grapevine swing-to-slide conversion with new track, gate hardware, and operator typically runs $1,500 to $3,200. Call (877) 610-2993 and we will measure the actual space and give you a written number.
The black cotton clay around Grapevine Lake and much of 76051 swells when wet and shrinks when dry, which heaves hinge posts inch by inch out of plumb. A misaligned post loads the gate leaf unevenly, the operator draws more current, and eventually the motor overheats, the gear strips, or the board throws an overload fault. We prevent it by cutting footings below the active clay zone, setting rebar deep, and re-hanging the gate leaf before reinstalling the operator. Same week that we did the hotel slide gate job, our crew reset a heavy ornamental swing gate at a Grapevine Lake estate after the hinge post had heaved 1.5 inches out of plumb, repoured the footing with deep-set rebar, and reinstalled the FAAC operator with a fresh safety photocell alignment so it held through the next dry spell. Call (877) 610-2993 to have someone measure your post plumb before the operator burns itself up.
Yes. Grapevine’s commercial properties near the airport and along SH-26 cannot afford a gate stuck closed during a spring storm or a rolling-brownout event. We install battery backup modules sized for the operator’s cycle count, which for a resort loading-dock gate means a battery bank that holds through dozens of cycles rather than just two or three. Battery backup for a commercial Grapevine operator runs $450 to $1,100 depending on voltage and required cycle capacity. Call (877) 610-2993 and we will specify the right unit for your actual gate, not a one-size guess.
Any automated gate operator in Grapevine must meet UL 325 entrapment protection requirements, which means either inherent current sensing that reverses the gate on contact, or external monitored photocells and contact safety edges. Most Grapevine residential gates have current sensing only, and most older installs never had the photocells aligned properly or at all. We install non-contact photocells and safety edges, set the reversing force correctly, and test the entrapment function before we call the job done. Entrapment protection is not an add-on; it is part of a proper operator installation. Call (877) 610-2993 with questions, or ask for a written list of what is missing when we quote the job.
Call (877) 610-2993 for a free estimate on any gate motor or opener work in Grapevine, TX. A live person answers, day or night, and Hal will quote the price before any work begins. The name is on the shop, and the shop is down the road.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Grapevine and the DFW metro since 2001.