Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Euless, TX
Gate repair in Euless typically costs between $120 and $700 depending on whether we’re adjusting a binding hinge or replacing a burned-out operator motor. Most repair calls in the 76039 and 76040 ZIP codes get same-day response, and you’ll talk to a live person when you call (877) 610-2993, day or night. Euless gates face a specific set of problems: Blackland Prairie clay heaving posts out of plumb, 1980s wrought iron suffering hinge fatigue, and commercial slide gates along the TX-121 corridor cycling hundreds of times daily until their motors fail. We bring a welding rig to every job so the gate stays in your driveway, not ours.
Why Euless Homes Are Different
Most of Euless’s residential neighborhoods were built between the 1970s and early 1990s, and those original wrought-iron swing and slide gates have been fighting the same fight for decades. Hinge fatigue, rust bleeding through powder coat, upright posts leaning just enough to make the gate scrape. The apartment and townhome complexes are even more telling: V-track slide gates on gated entrances log thousands of cycles a month, and the rollers and track wear flat.
Then there’s the dirt. Euless sits on Blackland Prairie clay, and that clay does the same thing every year: it swells in the wet winters, shrinks in the dry summers, and pushes gate posts out of plumb in the process. A gate that was square last spring can bind by August. We see this in Oakwood Terrace, near Cinnamon Court, and throughout the Bear Creek corridor. Summer heat in the 100°F range accelerates thermal expansion in powder-coated steel, cracking welds on western-facing gates and warping latch hardware until the motor can’t seat the gate properly.
Euless also sits directly against the western perimeter of DFW International Airport, and the TX-121/Airport Freeway corridor running through the city is lined with airport hotels, logistics warehouses, cargo facilities, and rental car operations whose vehicle-access gates cycle hundreds of times daily. That creates a commercial automated gate repair market that barely exists in neighboring Hurst or Bedford, where operator motors, loop detectors, and slide-gate hardware wear out on an accelerated schedule.
Gate Repair in Euless
Gate repair in Euless runs the gamut from a sagging residential swing gate off West Euless Boulevard to a burned-out commercial slide operator at a freight yard near TX-121. We fix the gate in your driveway rather than hauling it off or swapping parts that don’t need swapping. Our crew carries a welding rig, common parts for LiftMaster, Viking, Linear, and FAAC systems, and the tools to re-square a frame that’s been knocked out of true by shifting clay.
Hinge and Latch Repair
On a wrought iron swing gate in Euless, the hinge is where the weight concentrates. Older neighborhoods were built with gates hung on thin barrel hinges that were undersized the day they were installed. Forty years later, the gate has leaned enough to shear the hinge pin or wallow out the mounting holes in the post. We cut the old hinge off, weld in a heavier one sized for the actual gate weight, and re-square the gate so it latches without lifting. Most hinge repairs in Euless run $120 to $250, depending on how much welding is needed and whether the post itself has started to move in the clay.
Post Re-Set and Re-Square
Euless clay is the reason post work is our most-requested repair. When a wet spring swells the soil and a dry August shrinks it, a post set in a shallow footing will lean. A leaned post kinks the gate frame, binds the operator, and eventually snaps the weld at the hinge. We dig out the old footing, set a deeper post in gravel-drained concrete, and weld the hinge plates back on while the gate hangs in position. Gate re-square and post adjustment in Euless typically runs $250 to $450, depending on post condition and whether we’re re-setting or reinforcing against future clay movement.
Operator Motor and Control Board Repair
The apartment and townhome communities scattered through 76040 keep us busy with slide gate operators that have simply worked themselves to death. Before recommending a full replacement, we check the motor itself, the capacitor, the control board, and the power supply, because half the operators suspected of being dead are actually suffering from low voltage, a fried capacitor, or a misaligned limit switch. Operator motor replacement in Euless generally runs $380 to $700, depending on the brand and whether we’re matching a residential or commercial duty cycle. Gate Repair is what we built this company on, and we still approach every job with the same repair-first mindset.
How much does gate repair cost in Euless?
Most residential gate repairs in Euless fall between $120 and $450, with commercial slide gate operator replacements running $380 to $700. The final number depends on whether we’re welding a new hinge, re-setting a post in clay, or swapping a motor that’s been overloaded by a binding track. Call (877) 610-2993 for an exact quote - estimates are free, and the price is agreed before any work starts.
Can you come fix my gate today in Euless?
We can typically reach any address in Euless the same day you call, and in many cases within a few hours. Since dispatch and scheduling are coordinated from our Dallas-Fort Worth office and crews serve Euless locally, we don’t route your call through a national queue. A gate that won’t close gets priority, and the repair carries the same upfront pricing as any scheduled job.
Gate Installation in Euless
New gate installation in Euless means designing around soil that moves, sun that cracks welds, and traffic patterns that vary wildly between a quiet single-family lot off Bear Creek and a hotel shuttle entrance on TX-121. A new residential driveway gate in Euless typically runs $2,800 to $9,500 installed, depending on whether you’re going with a single swing, a double swing, or a slide gate. Commercial operators along the TX-121 corridor run higher because they need heavier hardware built for extreme duty cycles.
Driveway Gate Installation
Most Euless homes built in the 1970s through early 1990s either never had a driveway gate or have one that’s rusted past saving. New single swing driveway gates in the 76039 and 76040 zip codes usually run $2,800 to $5,500 installed, including a new operator. If you want a double gate for a wider driveway, expect $4,500 to $9,500. We set hinge posts with the Blackland Prairie clay movement in mind, using deeper footings and proper drainage so the post doesn’t heave out of plumb after the next wet cycle. We quote the price before we start, and that price doesn’t change at the door.
Slide Gate Installation
The TX-121/Airport Freeway corridor is lined with airport hotels, freight yards, warehouse entrances, and rental car facilities. Those slide gates cycle hundreds of times daily. If you operate a property along this corridor, you know the operator motors, loop detectors, and V-track hardware wear out on a schedule that would shock a residential homeowner. We install commercial-grade slide gates and operators built for that duty load. Residential slide gate installs run $3,500 to $8,000; commercial slide gates start around $6,000 and can reach $18,000 for heavy-duty double gates with advanced safety systems and loop detectors.
Pedestrian Gate Installation
Pedestrian gates are the workhorses of Euless’s many apartment complexes and townhome communities. These gates take abuse, and when the post rots or the latch fails, people prop them open. We install commercial-grade pedestrian gates with reinforced posts and self-closing hardware that meets current safety code. A typical residential pedestrian gate install runs $900 to $2,400. Gate Installation is scheduled and measured, not rushed, because a gate that’s undersized for its duty will fail before its time.
Why does my swing gate in Euless bind every spring after the ground dries out?
Your gate post is moving in the Blackland Prairie clay. This soil expands when wet and contracts when dry, and over a wet winter it pushes posts out of plumb. By spring, when the ground dries and contracts, the post has shifted enough that the gate binds in its arc or the latch no longer lines up. The fix isn’t adjusting the hinges. It’s resetting the post to plumb, deepening the footing, and welding the gate square to its new position.
Can my 1990s apartment complex slide gate operator be retrofitted to meet current UL 325 standards?
Most 1990s slide gate operators cannot be economically retrofitted to meet current UL 325 entrapment protection standards. The control boards lack the inputs for modern monitored photocells and safety edges, and adapter kits are unreliable on gates that cycle hundreds of times a day. On a low-use residential gate, a partial retrofit sometimes makes sense. On an apartment entrance gate off Fuller-Wiser Road that runs constantly, you’re generally looking at full operator replacement.
Gate Motor & Opener in Euless
Gate motor and opener work in Euless typically runs between $325 and $1,450 depending on whether we’re repairing an existing operator or installing a new one. Most repairs in the 76039 and 76040 ZIP codes are completed the same day we get the call. We’ve been fixing automatic gates long enough to know exactly which apartment-complex slide gates near the airport corridor are going to fail next, and why.
Motor Repair
Gate motor repair in Euless typically costs $325 to $650 depending on what failed. A control board replacement, gearbox rebuild, or limit-switch repair on a swing gate operator is the most common job we handle. Before recommending a full replacement, we check the motor itself, the capacitor, the control board, and the power supply, because half the operators suspected of being dead are actually suffering from low voltage, a fried capacitor, or a misaligned limit switch. Hal fixes the gate in your driveway rather than hauling it off or swapping parts that don’t need swapping.
Motor Installation
New gate motor installation in Euless runs $750 to $1,450 for a typical residential swing or slide gate, including the operator, mounting hardware, safety edges, and a full test cycle. On the apartment and townhome communities scattered through 76040, we routinely install commercial-grade slide operators built for the duty cycles those entrance gates actually see, not the light-duty units a residential company would quote. We install LiftMaster, Viking, DoorKing, Elite, FAAC, BFT, Linear, Ghost Controls, and Mighty Mule systems. The price is quoted and agreed before any work starts.
Linear and Slide Motor Service
Linear gate motors, used on slide gates, are built for long travel runs, and they’re standard on the V-track slide gates found at apartment and townhome entrances throughout Euless. A typical linear motor installation runs $850 to $1,400, and the most common repair we perform is replacing a limit switch or a worn drive belt that causes the gate to stop short or overshoot. We see a lot of Linear and DoorKing slide operators along the TX-121 corridor where vehicle access gates cycle hundreds of times daily. Those units need commercial-grade replacement, not a residential motor that will burn out in 18 months. Gate Motor & Opener service is what keeps your gate moving when the Texas heat and clay are working against it.
How quickly can you get to Euless for a gate motor repair?
We can typically reach any address in Euless the same day you call, and in many cases within a few hours. Since dispatch and scheduling are coordinated from our Dallas-Fort Worth office and crews serve Euless locally, we don’t route your call through a national queue. Call (877) 610-2993 and we’ll give you a real arrival window, not a promise we can’t keep.
Do Euless prices differ from nearby cities for gate motor work?
Our pricing is consistent across the county, but the mix of work in Euless leans toward slide gates and commercial-duty operators because of the multifamily communities and airport-adjacent corridor. That sometimes means the job we quote is a commercial-grade unit rather than a residential one, and the price reflects that. You’ll always get a written price, and the $40 off any repair over $200 and senior/veteran discounts apply the same everywhere we work.
Gate Access Control in Euless
Gate access control in Euless means keypads, card readers, phone entry, and video intercoms that hold up to the city’s unusual mix of aging apartment gates and heavy commercial traffic. In most Euless neighborhoods, we’re on site within 24 to 48 hours, and we answer the phone with a live person at (877) 610-2993 whenever you call. Hal still handles the jobs himself or sends a small crew that reports directly back.
Keypad and Phone Entry
We install, repair, and retrofit keypad entry systems for residential and commercial gates across Euless. Older keypads on apartments near the 76040 corridor often fail because the membrane buttons crack in the summer heat, especially on gates with full western exposure. Phone entry is a big one in Euless because so many apartment properties and warehouse offices rely on a dial-to-open box that the shuttle driver or vendor uses from the callbox. Those older phone entry boards degrade in the humid months, and we see plenty of call-drop issues on rental car lots and freight gates along TX-121. Keypad replacement or repair in Euless typically runs $180 to $420. Phone entry repair, including a new cellular bridge if the landline is dead, runs $300 to $650.
Card Readers and Video Intercom
Card readers make sense for Euless properties with frequent turnover: apartments, self-storage, freight yards. We install proximity card readers, replace worn keypad-card combos, and program multi-tenant systems. Video intercoms are replacing phone entry boxes all over Euless, especially at apartments and warehouse offices that want to see who’s at the gate. We integrate video intercoms into existing operators, including legacy DoorKing, Linear, and FAAC units. Card reader installation for a single entrance is generally $450 to $900. Video intercom integration runs $650 to $1,400 depending on the operator and whether we’re replacing just the monitor or running new wiring.
Commercial Access Control Retrofit
A full access control retrofit on a commercial slide gate along TX-121 can run $1,200 to $3,500, and we’ll tell you before we start whether your existing operator actually needs replacing or whether a retrofit board will do the job for a third of the cost. Smart access through a phone app makes sense on the commercial corridor where property managers aren’t on site every day and need to open a gate from across town. Gate Access Control is about matching the hardware to the actual traffic, not selling the most expensive system.
Can you retrofit my 1980s Euless apartment gate operator to meet current UL 325 standards?
In many cases, yes, we can retrofit the operator. The 1980s-era operators around Euless, especially DoorKing and Linear units on apartment gates, often have control boards that predate modern safety photocell inputs. We install a retrofit board that recognizes current UL 325 sensors, so the gate meets entrapment protection without replacing the motor or gearbox. The exception is when the operator’s motor has already burned out from years of clay-heave strain.
My rental car facility has an old phone entry system that drops calls. Can you integrate video without replacing the operator?
Yes, and this is one of the more common jobs we handle on the Euless commercial side. The old phone entry board is usually the failure point, not the gate operator. We replace the phone entry panel with a video intercom and bridge the new system into your existing operator. If your operator is a DoorKing or Linear from the late 1990s or early 2000s, that bridge is straightforward. Call (877) 610-2993 and we’ll look at what you’ve got.
Gate Parts & Welding in Euless
Gate parts and welding in Euless usually comes down to one question: is the post still holding, or has the clay moved it? We see both every week. A swing gate dragging the driveway, a slide gate jumping its track, a weld cracked clean through on the hinge side. Hal welds it in the driveway. We carry steel stock in the truck, so the repair happens the same visit.
Hinge and Rail Repair
On a wrought iron swing gate in Euless, the hinge is where the weight concentrates. We cut the old hinge off, weld in a heavier one sized for the actual gate weight, and re-square the gate so it latches without lifting. Slide gates are the load-bearing workhorses of Euless’s apartment stock. The V-track gates on 1970s and 1980s gated communities have rolled thousands of times, and the bottom rail is usually worn thin or split. We cut the bad section out and weld in new steel, then level the track so the gate rolls instead of grinding. Hinge replacement usually runs $180 to $380. Rail repair runs $220 to $480.
Post Replacement
Euless clay is the reason post replacement is our most-requested repair. We dig out the old footing, set a deeper post in gravel-drained concrete, and weld the hinge plates back on while the gate hangs in position. Post replacement, which involves cutting out the old footing and setting a new one, runs $350 to $700. For posts along TX-121 commercial fence lines or apartment slide gates, we’ll also spec heavier wall pipe and deeper embedment because the clay movement is relentless and a shallow post is a temporary post.
Custom Welding
Some repairs don’t have a part number. A custom scroll broken off, a driveway gate hit by a delivery truck, an odd-sized frame that needs a reinforcing gusset. Custom welding in Euless generally runs $120 to $450, depending on materials and how much grinding and fitting is involved. If the weld itself failed on a gate we previously fixed, the 90-Day Done Right Promise covers it. That promise is stamped in writing on every job, not buried in fine print. Gate Parts & Welding is where we started, and it’s still the core of what we do.
Why do Euless gate posts heave out of plumb more than in neighboring cities?
Euless sits on Blackland Prairie clay, which expands dramatically in wet winters and shrinks in dry summers. That repeated swelling and contracting lifts shallow footings. Bedford and Hurst have more mixed soil types with less movement, so their posts stay put longer. In Euless, a post set less than three feet deep in plain concrete will usually lean within a few years. We always set replacement posts deeper, with gravel drainage, to fight the clay.
My 1990s swing gate sags and scrapes the driveway-is the hinge or the post bad?
Both, usually. The hinge wears because the post has started to lean, and the lean puts extra weight on the hinge. By the time a gate scrapes the driveway, the post has moved enough to matter. We check the post with a level first. If the post has shifted, we reset it and replace the hinge at the same time. Fixing only the hinge on a moved post means you’ll fix it twice.
Brands We Service in Euless
We’re certified to service nine major gate brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. We stock common parts for FAAC, BFT, and Linear systems locally, which means most repairs don’t wait on shipping. If your operator is a brand we don’t carry, we’ll tell you upfront and help you source what’s needed. our brands
Pricing for Gate Repair in Euless, TX
| Service | Typical range in Euless |
|---|---|
| Minor hinge or latch repair | $120 - $250 |
| Hinge replacement (welded) | $180 - $380 |
| Gate re-square and post adjustment | $250 - $450 |
| Post replacement (full reset) | $350 - $700 |
| Rail repair (slide gate) | $220 - $480 |
| Custom welding (on-site) | $120 - $450 |
| Operator motor repair | $325 - $650 |
| Operator motor replacement | $380 - $700 |
| New motor installation (residential) | $750 - $1,450 |
| Linear motor installation | $850 - $1,400 |
| Slide motor installation | $650 - $1,350 |
| Keypad/phone entry repair | $180 - $650 |
What pushes price up in Euless: commercial duty cycles along TX-121, clay-heaved posts requiring deeper footings, and obsolete control boards that need full replacement rather than repair. Every quote is written, itemized, and agreed before any work starts. The price we give is the price on the invoice.
Neighborhoods We Serve in Euless
We don’t schedule by zip code; we schedule by who needs help. Most repair calls in Euless get a crew rolling within a couple of hours, not a couple of days.
- Oakwood Terrace
- Villa Norte
- Cinnamon Court area
- Bear Creek corridor
- Commercial properties along TX-121/Airport Freeway
Service Area - Cities Near Euless
We work throughout the mid-cities and northeast Tarrant County. If you’re near Euless, we likely cover your area with no trip charge inside the county. Nearby cities we serve regularly include Bedford, TX, Colleyville, TX, Hurst, TX, Grapevine, TX, and North Richland Hills, TX. Our Euless, TX crews are local and don’t route through a dispatch center three states away.
Serving Euless, TX - Our Local Coverage Area
Gatewood Fence & Gate crews serve Euless and the communities around it; dispatch is coordinated from our Dallas-Fort Worth office. The map shows the Euless coverage area; if your address is on it, we can help.
Also serving nearby: Euless, TX, Bedford, TX, Colleyville, TX, Hurst, TX, Grapevine, TX, North Richland Hills, TX.
FAQs About Gate Repair in Euless
Most residential gate repairs in Euless don’t require a permit, but new installations and any work that modifies the fence line or electrical service may need approval from the city. Commercial properties along TX-121 often have additional requirements for access control and safety equipment. We can tell you what applies to your specific job when we look at it.
Call (877) 610-2993 any time. A live person answers, 24 hours a day, and we’ll get you on the schedule. For repairs, we aim for same-day response. For installations, we set a time to measure, then deliver a written quote with no obligation.
Yes. Every job we do in Euless carries the 90-Day Done Right Promise in writing. If the repair or installation isn’t done right, one call brings Hal back to make it right. No forms, no escalation, no runaround. The name is on the shop, and the shop is down the road - that is the oldest accountability there is.
Call (877) 610-2993 for a free estimate on any gate repair, installation, or access control work in Euless. We’ll give you a real price, a real arrival time, and a real person on the other end of the line.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Euless Customers Say
"Welded the hinge back onto our wrought iron gate on site rather than taking it away for a fortnight. Ground it back and painted it and you cannot see the repair."
- Winston Achterberg"Fitted a keypad and an intercom so my mother can let carers in without coming down the drive. He set it up and then made her practise with it until she was comfortable."
- Lucinda Marchbanks"Beautiful gate and solid work. The build took about three weeks longer than the estimate because he was waiting on the ironwork, and I would rather have known that at the start than found out along the way."
- Beatrice Nwosu