Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Motor & Opener Across Conway
A gate motor and opener in Conway, FL typically runs $450 to $1,800 installed depending on the operator type, gate weight, and whether you need battery backup or intercom work done at the same time. We’re Gatewood Fence & Gate, and we’ve been fixing and installing gate openers in Conway since Hal Gatewood put his name on the shop in 2001. When your gate won’t open at 7 a.m. on a school day, you need someone who answers the phone and shows up. That’s what we do. Call (877) 610-2993 and you’ll get a live person, not a recording.
Conway has its own specific set of gate problems. The lakefront lots off Lake Conway Drive hold moisture year-round, the afternoon storms fry circuit boards, and a lot of the original ornamental iron gates around here are fifty and sixty years old. We know those gates. We know which hinges fail, which post footings heave, and which openers actually hold up in this humidity. That local knowledge is the difference between a repair that lasts and one you’ll be calling about again in six months.
Why Gatewood Fence & Gate Is Conway’s Preferred Gate Motor & Opener Company
Hal Gatewood’s name is on the shop and on every invoice. He’s not a franchise owner three counties away. When something goes wrong with your gate opener in Conway, you can call and talk to the same person who quoted the job. That matters more than people realize until they’ve dealt with a company that has no local face. Our Gate Motor & Opener team works on gates in Conway driveways, not in a warehouse somewhere.
We carry parts for the brands Conway homeowners actually have: Viking, Ghost Controls, DoorKing, LiftMaster, and the older Mighty Mule units still hanging on garages in 32812. If you’ve got an opener that another company said was “obsolete,” call us before you rip it out. Hal repairs what other outfits want to replace. Welding happens in your driveway, on-site, so your gate never leaves the property. That’s how we’ve done it since 2001, and it’s why customers in Conway keep our number in their phone.
Every job carries the 90-Day Done Right Promise in writing. If it’s not done right, Hal comes back. No runaround, no “we’ll get you on the schedule.” One call brings him back. And if you’ve already got a written estimate from another gate company, bring it to us. We’ll give you a free second opinion, and you might find out you don’t need half the work they quoted.
Our Gate Motor & Opener Services in Conway
Motor Installation
A new gate motor in Conway needs to be sized for the actual gate, not just ordered from a catalog. Lakefront properties often have heavy ornamental iron gates that weigh more than the original spec. We measure the gate, check the hinge posts, and install an operator that won’t strain against its limits. A typical Gate Installation in Conway for a swing gate motor runs $650 to $1,400, and a slide gate operator runs $850 to $1,800 depending on gate length and whether we’re running new conduit. Every install includes setting the safety sensitivity and testing the entrapment protection before we leave.
Motor Repair
Most our Gate Repair in Conway calls for gate motors come in two flavors: the opener stopped working after a storm, or it’s been getting slower and noisier for months. We troubleshoot the control board, limit switches, and drive mechanism right there in the driveway. Common repairs in the 32812 area include fried circuit boards from lightning, stripped drive gears on older slide operators, and photoelectric sensors that got knocked out of alignment by a swinging gate. Most motor repairs in Conway run $185 to $475, and we quote the full price before any work starts.
Linear Motor
Linear arm operators are common on Conway’s ranch-style homes, especially on the swing gates that came with 1960s-to-1980s houses. The linear arm pushes and pulls the gate leaf directly, and when the hinge post has shifted even slightly, that arm binds. We repair and replace linear motors from DoorKing, Elite, and Linear, and we always check the post alignment first. There’s no point putting a new motor on a gate that’s fighting its own hinges.
Slide Motor
Slide gates are the workhorse of wider driveways in Conway, especially on lakefront lots where the entrance is offset. But slide gate motors sit low, and on the properties near Little Lake Conway and Lake Barton, seasonal water pooling can submerge track hardware and corrode the motor mounting. We install slide motors with sealed housings and elevated mounting where needed, and we run underground wiring in anti-corrosion conduit. If your slide gate jerks, grinds, or refuses to move after a heavy rain, we’ll find out why.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Conway
We’re certified to service nine major gate opener brands, and in Conway we see a lot of Viking and Ghost Controls on newer lakefront installs, plus DoorKing on older slide gates that have been there for decades. We keep common parts for these brands on the truck, which means a repair that might take another company two trips and a week of waiting can often be finished the same day. If your opener is a Mighty Mule or a Linear unit that’s been discontinued, we can usually source the parts or retrofit the gate to a current operator without replacing the whole gate. That repair-first approach saves Conway homeowners thousands compared to the “replace everything” quote.
Common Gate Motor & Opener Problems We See in Conway Homes
- Lakeward post tilt. On lakefront streets off Lake Conway Drive and around Lake Barton, we routinely find gate posts leaning toward the water. Saturated soils undermine the water-side footer, the hinge post rotates a few degrees, and the gate sags until it binds against the latch post or drags on the drive. This is a Conway-specific failure mode; the lots a mile inland toward the 408 don’t have it.
- Storm-fried control boards. Central Florida’s June-to-September thunderstorms send lightning and power surges that take out circuit boards and safety photocells on automatic gate openers. If your opener died during or right after a storm, it’s likely the board, not the motor. We diagnose it before recommending a replacement.
- Corroded post hardware on 1960s-1980s iron gates. Conway’s original ranch houses came with ornamental wrought-iron gates that predate modern powder-coat finishes. Decades of lake humidity have eaten through original hinge pins and post brackets. The gate looks fine until the post hardware lets go and the gate drops.
- Misaligned rack and pinion on slide gates. When a concrete gate post footing settles or cracks on a Conway slide gate, the rack shifts out of line with the pinion gear. The motor strains, the gate shudders, and the gears wear out fast. We realign the rack and replace the worn pinion before installing a new motor.
On a lakefront street off Lake Conway Drive, we reset the hinge post of a 1970s ornamental wrought-iron swing gate whose footer had heaved toward the water, then installed a LiftMaster slide operator with battery backup and sealed the underground wiring in anti-corrosion conduit. The homeowner now has a silent-running gate that holds alignment through Conway’s summer storm season.
Pricing for Gate Motor & Opener in Conway, FL
Here’s what Conway homeowners can expect to pay for gate motor and opener work with Gatewood Fence & Gate:
- Gate opener repair: $185-$475 depending on the component (control board, limit switch, sensor, gear set)
- Swing gate motor installation: $650-$1,400
- Slide gate motor installation: $850-$1,800, higher for long or heavy ornamental gates
- Battery backup add-on: $250-$450 installed
- Intercom integration with gate opener: $300-$700 depending on wiring and existing equipment
- Full operator replacement with new safety edges: $1,200-$2,500
These are the ranges we quote in Conway for typical residential gates. Heavy custom iron gates or jobs requiring new conduit runs, post resetting, or underground wiring replacement will land at the upper end or beyond. We quote the full price before any work begins, and that price doesn’t change when the job’s done. The estimate is free. Call (877) 610-2993 and we’ll come out, look at your gate, and tell you exactly what it costs. No surprise line items, no “we found something else while we were in there.” There’s also $40 off any repair over $200, no trip charge inside the county, and a permanent 10% discount for seniors and veterans.
We Also Serve Cities Near Conway
If you’re just outside Conway, we also cover Orlando, Azalea Park, Belle Isle, and Pine Castle. The same crews work the whole area, so you get the same repair-first approach and the same written promise whether your gate is on a lakefront lot in 32812 or a dry lot a few miles north. If you’re in one of those nearby cities, our Gate Motor & Opener in Conway team can still get you taken care of, usually within the same week.
Serving Conway, FL - Our Local Coverage Area
We’re based in the Conway area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Motor & Opener in Conway
Lightning and power surges during Central Florida’s afternoon thunderstorm season fry the control board and safety photocells on automatic gate openers. It’s the most common post-storm gate failure we see in Conway, especially on lakefront lots where there’s less tall structure to deflect strikes. The fix is usually a new circuit board and surge protection, not a whole new motor. Call (877) 610-2993 for a diagnosis, and ask about adding surge protection to your existing opener.
Yes. In most cases we reset the existing hinge post by excavating the water-side footer, correcting the tilt, and re-setting the post in properly drained concrete. We do this on-site in the driveway, and we weld any cracked iron while we’re there. The gate doesn’t leave your property, and you don’t pay for a replacement post unless the old one is structurally gone. If you need Conway Gate Parts & Welding, we handle that on-site too. This is a repair we’ve done many times on the lakefront streets off Lake Conway Drive, and the 90-Day Done Right Promise covers the work in writing.
For Conway’s lakefront driveways, we typically recommend a slide gate operator with a sealed housing, elevated motor mounting, and battery backup. Lakefront lots hold moisture and see seasonal standing water, so the motor needs to stay dry and keep running when storms knock out power. On a heavy ornamental swing gate, a properly sized linear arm operator with stainless hardware is a better call than a light-duty residential opener. We’ll spec the operator to the actual gate weight and the site’s drainage before quoting anything.
Yes. Hal and the crew wire gate openers into existing intercom, telephone entry, and camera systems every week. Whether you’ve got an older DoorKing telephone entry pad at the street or a newer Wi-Fi-based intercom, we can tie the opener’s control board into whatever you’re using so one button opens the gate. We handle the low-voltage wiring, the relay logic, and the safety sensor coordination. If you’re building a new system, we’ll match the intercom to the opener so you’re not stuck with three separate remotes and two apps.
Florida requires automatic gates to have functional entrapment protection: either a reversing mechanism that stops and reverses the gate when it hits an obstruction, or external safety devices like photoelectric sensors and contact edges. Most Conway gates we inspect are missing at least one required safety device, especially older 1970s-1990s installs that were put in before the UL 325 standard tightened. We test the sensitivity, verify the sensors are aligned, and bring the gate up to current code before we sign off on any motor work. A gate that traps a child or a pet is not a gate we’ll leave working.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Conway since 2001.