Gate Repair in Everman - Same-Day Repair, Priced Before We Start

Gate Repair in Everman, TX

Gate repair in Everman typically costs $180-$340 for hinge and post work, and we can usually get to you same day or next morning depending on when you call. Most repair calls in ZIP 76140 trace back to the Blackland Prairie clay shifting posts that were set decades ago with little or no concrete. We’re Gatewood Fence & Gate, locally owned and owner-operated since 2001, and we fix gates at the source, not the symptom. Call (877) 610-2993 and a live person picks up, day or night.

Call (877) 610-2993

Why Everman Homes Are Different

Everman is a compact, working-class enclave in south Tarrant County where the dominant housing stock consists of modest 1950s-1980s ranch homes, the vast majority fenced with aging chain-link or treated-wood gates that were never upgraded. The ZIP 76140 area sits squarely on Blackland Prairie expansive clay, which heaves and contracts so aggressively between wet winters and dry summers that gate-post lean and sagging misalignment are the single most recurring repair call.

This soil-driven failure mode distinguishes Everman from sandier-soil suburbs to the west. A post set thirty or forty years ago in a few shovels of dirt now leans a few degrees, and that lean pulls the gate into the ground at the latch side or leaves a gap at the hinge side. It doesn’t matter how tight the hinges are when the post itself is moving. We set replacement posts deep, with proper concrete below the frost line, because anything less means redoing the same job in eighteen months.

Everman’s southern edge abuts light-industrial and commercial land uses along the south Fort Worth freight corridor, so our crew routinely shifts in a single day from rehanging a sagging wood residential gate on a 1960s lot to servicing a heavier steel slide gate at a small trucking yard or contractor storage facility. That mixed residential-commercial workload is unusual for a city of under 7,000 residents, and it keeps our welding gear and heavy-duty parts stocked on every truck.

Gate Repair in Everman

Gate repair in Everman usually means one of two things: a sagging swing gate on a 1960s ranch home, or a heavier slide gate at a commercial yard along the south freight corridor. Most jobs we handle in the 76140 zip run $180 to $340 for hinge and post work, and we can typically get to you same day or next morning. The Blackland Prairie clay under Everman shifts posts out of plumb year after year, and that changes how we approach every repair. Gate Repair is what we’ve built our name on, and we don’t haul your gate away for a week when we can weld it in your driveway today.

Hinge & Post Repair

This is the most common call we get in Everman. Posts set decades ago, often with minimal or no concrete, lean and heave with the clay. A gate sags in the hinge post, not in the middle, and that is where we start. We cut out the old footing, set the post deep in fresh concrete, and reweld or rebolt the hinges. On-site welding means the gate stays in your driveway. Post resetting with fresh concrete runs $260 to $450 depending on how deep and how much concrete the hole needs.

Electric Gate Repair

Electric gate repair in Everman covers openers, control boards, safety edges, keypads, and wiring. We service FAAC, BFT, Linear, Viking, LiftMaster, Ghost Controls, DoorKing, Elite, and Mighty Mule units. The February 2021 freeze left a wave of deferred damage in this area: operators not rated for extended sub-freezing exposure failed quietly and then died months later. Electric opener diagnosis and repair runs $180 to $350 for most jobs. If your opener has been acting up since that storm, call us at (877) 610-2993 before it quits with the gate half open.

Gate Realignment

Realignment fixes binding, dragging, failed latches, and gates that won’t close square. In Everman specifically, realignment is rarely about the panel itself. It’s about the post angle, the hinge sag, and the rack-and-pinion wear on operators where the footing shifted just enough to bind the rack. We square the gate, reset the latch, and adjust the opener so it cycles clean. Hinge replacement or latch repair on a standard chain-link gate runs $120 to $240.

Why does my gate post keep leaning a few degrees every year in Everman, even after I straighten it?

The Blackland Prairie clay under ZIP 76140 expands and contracts with moisture swings, and it never lets go of a shallow post. Straightening the gate without re-setting the post in deeper concrete treats the symptom, not the cause. We cut out the old footing, set the post deep, and that’s what actually stops the annual lean. Call (877) 610-2993 and we’ll look at the footing depth before quoting anything.

What does a sagging swing gate actually need - a new panel or something else?

Almost always something else. A gate sags in the hinge post, not in the middle. Everman’s clay soil heaves shallow posts out of plumb, and the panel is usually fine. We re-set the post, replace the hinge brackets if they’re wallowed out, and re-square the latch. You only pay for what’s actually wrong. Call (877) 610-2993 for a free look.

Gate Installation in Everman

If you live in the 76140, you know the feeling: the gate that swung clean last spring now drags a groove through the grass by August. That is not a hinge problem, not really. It is the Blackland Prairie clay under Everman heaving and shrinking with every wet winter and dry summer, slowly torquing gate posts out of plumb until the latch misses by half an inch and the whole thing binds. Most gate installers never think about what is under the dirt. We do, because a gate installed without accounting for that clay will bind before the concrete cures. Gate Installation in Everman means measuring the soil conditions, not just the opening.

Driveway Gate Installation

Most driveways in Everman are modest, and so are the gates that serve them. We measure your driveway width, check the approach angle from the street, and recommend a gate that clears the ground without scraping when that clay shifts seasonally. A typical single driveway swing gate in Everman runs $1,200 to $2,800 installed, depending on steel gauge, height, and whether you want an operator on it now or just future-proofed mounts for later.

Pedestrian Gate Installation

The side gate every 1950s ranch in Everman has off the carport or back patio takes a beating from kids, dogs, and the weather. We build pedestrian gates that close square and stay square. Price for a standard 36- to 42-inch steel pedestrian gate with new posts set in concrete typically lands between $650 and $1,400 in Everman. Add a keyed lock and closer and you are still under $1,700 on most lots.

Sliding Gate Installation

Sliding gates make sense where a swing gate would eat half the driveway, which happens more than you would think on Everman’s smaller lots. We install cantilever and track-style slide gates for homes and for the light-industrial yards along Everman Parkway. A residential sliding gate installation in Everman generally runs $2,400 to $5,500 depending on length and whether we run power to the operator.

Can you replace a gate the same day in Everman?

For a simple gate swap where the posts are solid, we can often complete a pedestrian or standard driveway gate in one visit. Full installations with new posts, concrete, and curing time take longer by design. We will tell you when the concrete is ready for load before we hang the gate and walk away. Call (877) 610-2993 to schedule a free measure.

Is gate installation in Everman more expensive than in nearby cities?

Our gate pricing for Everman runs in line with Rendon, Kennedale, and Forest Hill. The one thing that can add cost anywhere in the area is soil correction, and the clay under the 76140 sometimes requires setting posts deeper or adding a wider footing. We will show you what that costs before any concrete gets poured, not after. Call (877) 610-2993 for a written estimate.

Gate Motor & Opener in Everman

When a gate motor quits in Everman, it rarely happens at a convenient moment. The gate stops midway across the driveway on Enon Avenue, or the opener hums without moving on a cul-de-sac off Shelby Road, and now the car is trapped inside the fence line. That’s the reality for homeowners across the 76140 ZIP code, where many residences still run the basic swing gates installed with those original 1950s through 1980s ranch homes. Gate Motor & Opener service here means understanding both the motor and the clay-heaved post that’s making it work overtime.

Motor Installation

Most homes in Everman were built before automatic driveway gates were common, which means we’re often installing a motor on a gate that was never designed for one. That’s fine. We reinforce the hinge post, set proper concrete footings where the original post was just dropped in dirt, and mount the opener so it works with the gate’s natural arc. A full motor installation in Everman runs $650 to $1,400 depending on gate weight and power access. The written quote covers everything before we touch the first bolt.

Motor Repair

When an operator fails in Everman, the culprit is usually one of three things: a capacitor cooked by a Texas heat wave, a control board damaged by the February 2021 winter storm’s extended freeze, or a motor burning out because a clay-heaved post made the gate fight every cycle. We diagnose on-site and replace only what’s actually dead. Basic repairs like capacitor swaps, limit switch adjustments, and remote reprogramming run $180 to $320. Control board replacement lands between $280 and $520. You’ll know the number before we start.

Slide Motor

South Everman abuts the industrial strip along the freight corridor near the south Fort Worth line, and that changes the work mix. We’re as likely to be servicing a heavy steel slide gate at a small trucking yard or contractor storage facility as we are a residential swing gate off Oak Grove Road. Slide motors take more abuse than swing operators because the track collects debris and the gate weight stresses the drive chain constantly. A slide motor replacement in the Everman market runs $800 to $1,600 including the motor and new chain.

How fast can you get to Everman for a gate motor repair?

Same-day service is available for most repair calls in the 76140 ZIP code. Our scheduling is coordinated from the Dallas-Fort Worth office, and our crews work Everman routes daily. If a gate motor fails and your car is trapped inside the fence, let us know when you call and we’ll prioritize your address. Call (877) 610-2993 and a live person answers, 24/7.

Do you service the older ranch homes in Everman, or just new construction?

Older ranch homes are most of what we service in Everman. The city’s housing stock runs heavily to 1950s through 1980s single-story builds, and the gates on those properties are usually the original swing gates or early retrofits. We’re comfortable with shallow-set posts, outdated operator brands, and gates that were never meant to carry a motor. That’s the daily work in this market. Call (877) 610-2993 to describe what you’ve got.

Gate Access Control in Everman

Gate access control in Everman means keypads, remotes, phone entry, and card readers that actually work on gates built back when Eisenhower and LBJ were in office. Most calls we run in the 76140 ZIP start the same way: a keypad went dead, a remote stopped triggering the opener, or an old phone entry box finally gave up. Hal has been fixing and retrofitting gates since 2001, and he’ll tell you straight which parts can be saved and which belong in the scrap bin. Gate Access Control in Everman is as much about honest diagnosis as it is about new equipment.

Keypad Entry

Keypad entry on an Everman gate has to survive two things: direct summer heat and the seasonal ground shift that pulls posts out of plumb. A keypad wired to a board inside an operator that’s bolted to a heaving post will throw false open-close signals when the gate leaf hangs crooked. That’s the puzzle we solve first: fix the post, then program the keypad. A keypad replacement or new wireless keypad install in Everman typically runs $180 to $340, depending on whether the operator board needs a new receiver or the keypad wiring has to be pulled fresh.

Remote Control

Remotes fail for a reason. Sometimes it’s a dead board in the operator, sometimes it’s a receiver that lost its programming after the February 2021 freeze that wrecked a lot of 1980s-era boards across Everman. We diagnose the whole chain: button, transmitter, receiver, board. Then we replace only what’s actually dead. If you’ve got three remotes and only one works, the problem usually isn’t the remotes, it’s the receiver sitting in a housing full of corrosion from wet winter air.

Phone Entry

Phone entry boxes are a big thing in Everman because a lot of properties still have the original iron or chain-link gate with a call box wired to a landline that’s no longer even active. We can’t resurrect a box whose board is beyond fried, but a surprising number of them just need a new relay, a cleaned contact, or a reprogrammed directory. Phone entry box repair runs $150 to $300 when the board and relay can be saved; full replacement of a dead phone entry system starts around $600 and goes up with wiring condition.

Why does my Everman gate keep needing its keypad reprogrammed after every big rain?

Your gate keeps losing its keypad programming after rain because water is getting into the keypad housing or the operator board enclosure, usually through a failed gasket, cracked conduit, or an old keypad that was never sealed properly. In Everman, the wet winter-spring cycle on Blackland clay also shifts the gate post slightly, which can pull low-voltage wiring loose inside the operator and reset the board. We replace worn housings, reseal enclosures, and reset posts so the wiring stays put. Call (877) 610-2993 before the next storm.

My automatic gate doesn’t have photo eyes - is that a safety problem?

Yes. A gate without photo eyes or an equivalent entrapment device can close on a person, a pet, or a vehicle, and it’s the most common safety gap we see on pre-1990 operators in Everman. Modern UL 325 standards require a monitored entrapment device, and we retrofit photocell pairs and safety edges onto legacy operators for $220 to $380, which is far less than a lawsuit or an ambulance ride. Call (877) 610-2993 for a safety check.

Gate Parts & Welding in Everman

Gate parts and welding in Everman usually means one of two things: a hinge post that the Blackland Prairie clay has torqued out of plumb, or a cracked rail on a gate that’s been swinging since the Kennedy administration. We handle both, and most jobs are done the same day we show up. If you’re on a 1960s ranch lot off W Enon Avenue or a lighter commercial yard near the south Fort Worth freight corridor, you already know the value of a crew that welds on site instead of hauling your gate to a shop across the county. Gate Parts & Welding is where we started, and it’s still the backbone of what we do.

Hinge Replacement

Most hinge failures in Everman aren’t hinge failures at all. The post moves, the hinge bolts wallow out, and the gate drags until the latch won’t catch. We replace hinges with heavier barrel hinges or weld-on strap hinges, but we check the post first. In the 76140 clay, a new hinge on a leaning post is a waste of money. Hinge replacement on a single gate runs $120 to $260, but only after we’ve made sure the post is solid.

Post Replacement

This is the single most common repair ticket in Everman. The original 1950s-through-1980s chain-link posts were often set with minimal or no concrete footing, so the expansive clay works them loose year after year. We dig out the old post, set the new one deep with proper concrete, and weld the rails back solid. A post set right in Blackland Prairie clay stays put. A post set shallow doesn’t. Typical post replacement runs $310 to $575 depending on depth and whether the rail needs cutting and re-welding.

Rail Repair

Cracked or bent rails on a swing gate are usually either weld-repairable or they’ve reached the point where cutting out the section and welding in new steel makes more sense. On chain-link gates, the top rail bends from kids climbing or from decades of the latch being yanked. On steel tube gates at small trucking yards along the south Fort Worth corridor, fatigue cracks at the weld joints are common. We grind, weld, and reinforce in place. Rail repair and weld crack work runs $140 to $340. You keep the gate, we fix the rail.

Why do my gate hinges keep pulling loose in Everman even after I replace them?

The hinge is almost never the real problem in Everman; the post is moving in expansive clay and wallowing out the hinge screw holes. Until the post is reset deeper with proper concrete, any new hinge will start pulling loose within a season. We fix the post first, then hang the gate once. Call (877) 610-2993 for an exact quote.

Is it cheaper to weld a cracked gate rail or replace the whole gate?

In nearly every case, welding is far cheaper. A cracked rail on a steel tube gate in Everman typically costs $140 to $340 to weld and reinforce on site. Replacing the whole gate runs $1,200 to $2,500 plus post work. If the gate is structurally sound aside from the crack, I’ll tell you to weld it. Call (877) 610-2993 for an honest read on it.

Brands We Service in Everman

We carry parts and stock common components for FAAC, BFT, Linear, Viking, LiftMaster, Ghost Controls, DoorKing, Elite, and Mighty Mule operators. Most repairs in the 76140 ZIP don’t require a two-week parts order because Hal keeps the truck shelves loaded with what fails most often on the brands he sees every week. our brands

Pricing for Gate Repair in Everman, TX

Neighborhoods We Serve in Everman

We’re in and out of Everman’s residential streets every week, and typical response for a repair call is same-day or next morning depending on the time you reach us. Our crews know the lot sizes, the original fence lines, and which blocks still run on shallow-set posts from the 1960s.

• The original ranch-home blocks around Enon Park and W Enon Avenue
• Streets off Oak Grove Road near Everman Joe C. Bean High School
• The mixed residential and light-commercial edge along the south Fort Worth freight corridor
• Older subdivided lots throughout central ZIP 76140
• Properties near Everman Parkway with smaller lots that favor sliding gates

Service Area - Cities Near Everman

Our crews work the Dallas-Fort Worth metro with Everman as a regular service area, and we carry the same tools and parts to neighboring towns. If you’re near Everman, we also serve Rendon, TX, Kennedale, TX, Forest Hill, TX, Burleson, TX, and Crowley, TX. Dispatch and scheduling are coordinated from our Dallas-Fort Worth office, but the person who shows up at your gate knows these streets.

FAQs About Gate Repair in Everman