Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Motor & Opener Across Everman
If your automatic gate in Everman is binding, stalling, or refusing to open, the problem usually isn’t the motor itself. It’s what the clay underneath ZIP 76140 did to the post before the motor ever tried to move it. We fix both. Gatewood Fence & Gate has been handling Everman Gate Repair and installing gate motors and openers since 2001, and we work across Everman every week. A live person answers our phone 24/7 at (877) 610-2993. Not a voicemail, not a call center three states away. You call, you get us.
Our Gate Motor & Opener work in Everman starts with the post, because that is where the failure starts. If the post leans, the operator binds. If the post heaves, the arm drags. If we do not fix the foundation under the opener, we are selling you a repair that comes un-done by next summer. That is how we approach every job in Everman, and it is why our repair calls here run different from what a generic gate company expects.
Key Takeaways
- Gate motor and opener repair in Everman typically runs $180 to $480 depending on the failure, and we quote the price before any work starts.
- Most Everman gate failures start with clay-heaved posts, not with the motor itself. We fix the post first, then the operator.
- We stock parts for LiftMaster, FAAC, BFT, Linear, and Viking, and we service nine major brands total.
- Every repair carries our 90-Day Done Right Promise in writing. If it is not right, we come back and make it right.
Why Gatewood Fence & Gate Is Everman’s Preferred Gate Motor & Opener Company
Hal Gatewood’s name is on the shop and on every invoice. That is the oldest accountability there is. We are not a franchise truck passing through. We publish our address and license number, and if you ever want to see the person who will be working on your gate, you can drive to the shop and look him in the eye.
Everman’s housing stock runs heavy to 1950s through 1980s ranch homes, many with original chain-link perimeter fencing and swing gates whose posts went in the ground decades ago with minimal concrete. That means the repair mix here tilts toward post resetting, hinge and latch replacement, and operator arms that stopped working because the post moved underneath them. We know that before we even pull up. It is not guesswork. It is just what Everman gates do.
Calls are answered by a live person around the clock. A real human picks up at (877) 610-2993, not a dispatch queue. If you have a gate stuck open at 2 a.m. on a Sunday, you get Hal or someone on his crew. Not a recording.
We also show up when we say we will. Our crews serve Everman locally, coordinated from the Dallas-Fort Worth office. No trip charge inside the county. No estimate that changes at the door.
Our Gate Motor & Opener Services in Everman
Motor Installation in Everman
Gate Installation in Everman for a new gate operator runs $850 to $2,400 installed, depending on the gate’s weight, length, and whether it is a swing or slide. That price includes the operator, arms or rack, safety photocells, and wiring to a proper power source. We set posts with four-foot deep footings and reinforced concrete on clay ground, because on Blackland Prairie, a shallow set is a warranty claim waiting to happen. Before any work begins, you get a written price. That price does not change unless the gate itself reveals something we could not see from the surface, and if it does, we stop and talk to you first.
Motor Repair in Everman
Most motor repairs in the 76140 area fall between $180 and $480. That covers failed capacitors, burned control boards, stripped gears, misaligned limit switches, and operator arms that bind on a moved post. We repair first. If the motor can be fixed in your driveway, we fix it there. We do not haul it off and tell you it needs replacing just because that is the easier invoice. Everman Gate Parts & Welding on-site means we can reinforce a cracked operator mount or fabricate a new arm bracket without sending your gate anywhere. You keep your gate. We fix it where it hangs.
Linear Motor Service in Everman
Linear is a brand we see constantly on older Everman slide gates, especially on the small contractor yards and storage facilities along the south edge of town near the freight corridor. The typical failure on a Linear operator is a stripped drive gear or a limit switch that drifted. Parts run $40 to $180, and labor lands between $120 and $300 depending on access. We keep common Linear components on hand so we are not waiting on a parts drop to get your yard gate moving again.
Slide Motor Service in Everman
Slide gates carry a heavier workload than swing gates, and on Everman’s clay, the track and rack take the abuse before the motor does. A slide gate repair here usually costs $220 to $650, including rack alignment, roller replacement, or a motor rebuild. Undersized slide operators that were installed years ago on contractor yards near the industrial edge are a problem we see over and over. Wind load, misaligned posts, and years of grit chew through those units. We size the operator to the gate and the gate to the ground, not the other way around.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Everman
We are certified to service nine major gate brands, and in Everman we see a lot of LiftMaster, FAAC, BFT, Linear, and Viking. We stock local parts for those makes and the others we carry, so most repairs are done in a single visit. If you have an older BFT slide operator that needs a control board, we usually have it in the van. If you have a Viking swing arm that trips mid-cycle on a heaving post, we know the failure before we even test it. We see these units weekly across south Tarrant County, and the pattern is always the same: the ground moves, the post follows, the operator fights it, and the operator loses.
Common Gate Motor & Opener Problems We See in Everman Homes
- Clay heave tilting the hinge post. Everman sits on Blackland Prairie expansive clay. Wet winters swell it. Dry summers shrink it. A post that was set in the 1970s with no proper footing pivots enough to bind a swing gate operator’s arm, and the entrapment sensor trips mid-cycle every single time. We auger a four-foot deep footing with rebar and high-strength concrete, then rehang the gate so the operator closes cleanly.
- Undersized slide operators on contractor yards. The southern edge of Everman abuts the south Fort Worth freight corridor, and small trucking yards and contractor storage facilities there run heavy steel slide gates on operators sized for a residential panel. Wind load and rack wear from misaligned posts finish them off early. We size the replacement to the actual gate weight and the exposure it faces.
- Battery backup failures from the February 2021 freeze. Solar gate openers with battery backup took a beating during that storm, especially where the battery enclosure was uninsulated. Weak charging circuits now drain early or fail entirely. We replace the battery and the charging board, and we route the wiring so it survives the next hard freeze.
- Sagging gate arms from failed post footings. A gate sags in the hinge post, not in the middle. Show us a gate closing on its own and we will show you where it is failing. When the arm sags, the motor works harder, the gears strip, and the problem spreads. Fix the post without the panel and you fix it twice. We fix it once.
Pricing for Gate Motor & Opener in Everman, TX
Here is what Everman homeowners and property managers can expect to pay. Motor repair runs $180 to $480. A new operator installation lands between $850 and $2,400. Slide gate repair sits at $220 to $650. Battery backup replacement is typically $150 to $380. Intercom integration onto an existing system runs $400 to $1,200, depending on whether we are integrating with an existing camera or running new wiring. Every price is quoted and agreed before any work starts. No trip charge inside the county. $40 off any repair over $200. A permanent 10% discount for seniors and veterans. And every job comes with the 90-Day Done Right Promise in writing. If it is not done right, one call brings us back.
We Also Serve Cities Near Everman
In addition to our daily work in Gate Motor & Opener in Everman, we serve nearby communities like Rendon, Kennedale, Forest Hill, and Burleson. If you are a few minutes down the road and your gate is down, call us. The same crew, the same pricing, the same promise. We know these roads because we drive them every week.
Serving Everman, TX - Our Local Coverage Area
We’re based in the Everman area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Motor & Opener in Everman
Because the Blackland Prairie clay under your post swells when it takes on water, and the post tilts just enough to throw the operator arm out of alignment. The fix is a deep post footing with rebar and high-strength concrete so the post stops moving with the seasons. We see this failure more in Everman than in sandier-soil suburbs to the west, and we correct it the first time. Call (877) 610-2993 and we will take a look.
Yes. Battery backup installation on a LiftMaster operator typically runs $150 to $380, depending on the model and whether we need to add a new charging board. We also replace freeze-damaged charging circuits from the February 2021 storm and route the wiring so it survives the next hard freeze. Call us and we will quote it before we start.
The rack is likely misaligned from clay-driven post movement, and the rollers or the drive gear are chewing at one point in the track. That grinding spot is where the gate binds. We realign the rack, replace the worn rollers or gear, and re-set the posts if the clay has moved them. If the operator is undersized for the gate’s actual weight, we will tell you that too. Call (877) 610-2993 for a free estimate.
Yes. We have integrated intercom and camera entry with custom ornamental swing gates throughout the 76140 area, including historic ranch properties and higher-end residential work. The integration includes wiring, mounting, and programming so the intercom, camera, and operator communicate. Typical integration runs $400 to $1,200 depending on what is already in place. Call us and we will walk you through what your gate needs.
We fix the hinge post, not the panel. The sag is in the post. On Everman clay, the post has pivoted because it never had a proper concrete footing. We auger a four-foot deep footing, set the post with rebar and high-strength concrete, rehang the gate, and re-mount the operator arm. The gate closes silently after that. The whole repair runs from $180 to $480 depending on the arm and the operator. Call (877) 610-2993 and we will give you an exact price before any work begins.
What Everman’s Clay Does to a Gate Motor That No One Else Talks About
Everman sits on Blackland Prairie expansive clay. That is the single most important fact about gate motors in this town. The clay heaves and contracts with seasonal moisture swings, and every time it moves, it torques the gate post. A post tilts a fraction of an inch. The operator arm binds. The motor strains. The gears strip. The entrapment sensor trips and the gate stops halfway. Repeat that cycle enough times and the motor dies, not because it was a bad unit but because it spent three years fighting the ground under it.
We re-set a twisted hinge post on a 1970s ranch home’s custom ornamental swing gate along the south edge of Everman near the freight corridor. The original post had no concrete footing at all. Just a hole and some packed dirt. We augered four feet down, set rebar, poured high-strength concrete, and mounted a LiftMaster swing gate operator with new safety photocells. The gate had been dragging on the clay-heaved pad for years. After the reset, it closed without touching the ground. That is the difference between repairing the motor and repairing the cause.
This is not a lesson you learn from a manual. It is a lesson you learn from eight or nine hundred gates on this soil. Everman’s gates fail from the ground up. A generic gate motor page will tell you to replace the capacitor. We will tell you the capacitor fried because the post moved and the motor fought it. Fix the ground. Then fix the motor. That is the only repair that holds.
Battery Backup After the Freeze
The February 2021 winter storm left a specific calling card in Everman: battery backups on solar gate openers with charging circuits that were never rated for extended sub-freezing exposure. Those batteries drain early now, and the charging boards fail silently. We replace the batteries and the boards, and we wire them to survive the next freeze. If your gate operator has not held a charge since that week in February 2021, that is not bad luck. That is a freeze-damaged charging circuit. We fix it.
Free Estimate - Call Us Now
If your gate motor is down in Everman, call (877) 610-2993. A live person answers. We will ask what the gate is doing, give you an honest idea of what it will take, and get you on the schedule. The price is written down before we start. No trip charge inside the county. $40 off any repair over $200. And if the job is not done right, the 90-Day Done Right Promise means we come back and fix it. Hal Gatewood’s name is on the shop. The shop is down the road. That is the oldest accountability there is.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Everman since 2001.