Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Crowley
Gate installation in Crowley usually costs between $1,800 and $6,500 depending on whether you’re putting in a manual driveway gate or a fully automated slide gate with access control. Most single swing gate installs run $1,800 to $3,200, while slide gates with operators land in the $4,000 to $6,500 range. We’re Hal Gatewood’s crew at Gatewood Fence & Gate, and we’ve been welding and hanging gates in the Fort Worth area since 2001. Call (877) 610-2993 and a live person answers, day or night.
Crowley is different from the fully built-out neighborhoods north of I-20. Down here off FM 1187 and Crowley Road, brand-new subdivision homes with ornamental iron driveway gates sit right next to older acreage parcels still running traditional ranch swing gates. That mix means the person showing up to your job needs to know both worlds. We do.
Why Gatewood Fence & Gate Is Crowley’s Preferred Gate Installation Company
Hal Gatewood started this shop in 2001 and his name is still on it. That matters in a town like Crowley, where people check each other’s work and remember who did right by them. When we install a gate in a subdivision off FM 1187, the neighbors watch. We’re fine with that. Our 90-Day Done Right Promise is stamped in writing on every job. If something’s not right, one call brings us back. No runaround.
We answer the phone with a live person 24 hours a day, seven days a week. You won’t get a voicemail tree or someone reading a script from another state. When you call about a gate installation in Crowley, you’re talking to a person who knows the difference between a swing gate on Blackland clay and one on sandy loam. That difference is the whole ballgame here, and we’ll get into why below.
We’re licensed and insured, and Hal publishes the shop address so anyone can drive by and look him in the eye. That’s the oldest accountability there is. The name is on the shop, and the shop is down the road from Crowley.
Our Gate Installation Services in Crowley
Driveway Gate Installation in Crowley
Driveway gates in Crowley get hit hard by two things: Texas heat and Blackland Prairie clay. The heat bakes the paint off cheap posts. The clay heaves the footings out of plumb. We install driveway gates with deeper bell-bottom footings that reach below the active clay layer, so the gate stays level through wet-dry cycles. On the newer subdivisions off FM 1187, we regularly see two-year-old posts already leaning. Show me that gate and I’ll show you where the footing failed.
Swing Gate Installation in Crowley
Swing gates remain the most common choice in Crowley, especially for the 2000s-to-2020s tract homes that dominate the area. But a swing gate is only as good as its hinge posts. A gate sags in the hinge post, not in the middle. That’s where we start, and that’s why we set posts deeper here than the standard spec calls for. Fix the panel without the post and you’ll fix it twice.
Sliding Gate Installation in Crowley
On acreage parcels around Crowley, a slide gate often makes more sense than a swing gate. There’s room for the track, the gate stays out of the wind, and the hardware can handle a heavier panel. We frequently convert failing swing gates to slide gates on county properties outside old town Crowley, where driveway aprons are long and grade changes over the years have pulled original swing hardware out of alignment. A rack and pinion slide conversion gives you a gate that doesn’t care what the clay does under it.
Pedestrian Gate Installation in Crowley
Pedestrian gates outlast driveway gates only when someone sets the post correctly the first time. In Crowley’s clay, a shallow-set pedestrian post starts leaning within one drought-and-recharge season. We pour deeper footings, weld hinges on site rather than using screw-in hardware that pulls loose, and set the latch so it actually catches. Whether you’re adding a walk gate to a subdivision fence off Crowley Road or replacing a rusted one at a 1980s ranch home, the install determines how long it lasts.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Crowley
We’re certified on nine major gate brands, but the ones we work on most in Crowley are FAAC, BFT, and Linear. These are common on both the subdivision homes and the older rural properties around 76036. Because we stock local parts for Crowley customers, turnaround on operator repairs and installs runs faster than ordering from a warehouse in another state. If a BFT slide motor needs a new limit switch, we likely have it. If not, we’ll weld a temporary fix so the gate keeps working while the part comes in. Nobody else around here is welding on site like we are.
Common Gate Installation Problems We See in Crowley Homes
- Builder-grade operators dying in two or three seasons. The original homebuilder installs a basic residential swing arm opener, the Crowley summer heat bakes it, the clay heaves the post it’s mounted on, and the motor burns itself out trying to push against a jammed panel. We replace it with a commercial-duty operator sized for the gate’s actual weight, not the weight stamped on the box.
- Manual gates with no conduit for future automation. A lot of Crowley homes had driveway gates installed manually. No conduit run. No power at the post. When the homeowner wants a keypad or a solar opener, the original install now means trenching through fractured, shifting clay. That’s far rougher digging than the sandier soils just north of town, and it’s why we recommend running conduit during the first install even if you’re not automating yet.
- Post footings poured at standard shallow depths. On a newer subdivision off FM 1187, our crew arrived to a two-year-old double driveway gate whose hinge posts were visibly out of plumb. The original builder installed a LiftMaster operator on a standard collar footing, but the Blackland clay had already heaved the posts. We cut and removed the old footings, augered deeper bell-bottom holes below the shrink-swell zone, set new posts, and rehung the gate with a rack and pinion slide conversion plus a loop detector and safety photocells so the new install stays true through the next wet-dry cycle.
- Latch receivers that miss after the ground moves. In expansive clay, the gate post leans and the leaf drops. The latch misses the receiver, the gate won’t stay shut, and sooner or later the wind catches it. Homeowners try to fix this by adjusting the latch. We fix it by addressing the post. Adjust the latch enough times and you’ve stripped the hardware. Address the post once and the gate works for years.
Pricing for Gate Installation in Crowley, TX
Here’s what we’re seeing in Crowley right now:
- Manual single swing driveway gate: $1,800-$3,200 installed
- Manual double swing driveway gate: $2,800-$4,800 installed
- Automated single swing gate with operator: $3,200-$5,000 installed
- Sliding driveway gate with rack and pinion operator: $4,000-$6,500 installed
- Pedestrian walk gate with hardware: $500-$1,300 installed
- Adding automation to an existing manual gate: $1,400-$2,800 depending on whether conduit already exists
Clay conditions in 76036 routinely require deeper footings than what a standard quote from a Fort Worth shop would include. We price for that up front, not as a surprise line item after the hole is dug. Every quote is written, agreed to before work starts, and finished at that number. No trip charge inside the county. Free estimates. Permanent 10% discount for seniors and veterans. Call (877) 610-2993 and we’ll come measure and hand you a number.
We Also Serve Cities Near Crowley
Besides Crowley, our crews run to Gate Installation jobs in Burleson, Everman, Rendon, and Benbrook on the same schedule. If you’re in one of those towns, the same pricing and the same 90-Day Done Right Promise apply. Dispatch and scheduling are coordinated from the Dallas-Fort Worth office, but the person welding your gate is local to the southern Tarrant County area.
Serving Crowley, TX - Our Local Coverage Area
We’re based in the Crowley area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Crowley
Because the builder set the post in a standard concrete collar footing that doesn’t reach below the active shrink-swell zone of Crowley’s Blackland Prairie clay. In 76036, gate posts on homes built as recently as two to four years ago are commonly found leaning because the clay expands and contracts enough through North Texas wet-dry cycles to rock the post out of plumb. We fix it by augering deeper bell-bottom holes below the active clay layer and resetting the posts. Call (877) 610-2993 for a free look at your posts.
Yes, in most cases. If the original installer ran conduit or left a junction box at the post, automation is straightforward. If not, which is common on Crowley homes built before automation was standard, we trench a narrow path for power rather than ripping up the whole driveway apron. We can also install a solar opener when running grid power is impractical. Call (877) 610-2993 and we’ll tell you which route fits your yard.
Every automatic gate operator in the United States must comply with UL 325, which requires entrapment protection like safety photocells or edge sensors. If your operator was installed in the last decade it likely has some protection, but many builder-grade installs in newer Crowley subdivisions have the bare minimum, or the sensors have drifted out of alignment as the clay moved the posts. We check every install and every repair for UL 325 compliance. If you’re unsure, call (877) 610-2993 for a safety check. This is not a warranty issue. It’s a safety issue.
We recommend a rack and pinion slide gate motor from BFT or FAAC with a substantial enough base to stay rigid even when the ground around it shifts. The key is isolating the motor from the clay. We set operator bases on deeper footings than standard spec, and we run wheels on a track that doesn’t care what the pad underneath does. A chain drive with a floating track is a cheaper install but becomes a maintenance headache on heaving ground. Call (877) 610-2993 for an honest recommendation based on your specific gate and grade.
You can, but nothing you add to a leaning post will last. The solar opener will work until the post heaves further and binds the panel, and then you’re replacing the opener and the post. We recommend you fix the post first. We can set it deeper below the clay line, then mount the solar panel and battery box on the corrected structure. That way the new automation lasts more than a season. Call (877) 610-2993 for a free assessment. Estimates are free, and we’ll tell you plainly whether the post needs to come out.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Crowley since 2001.
Ready to get your Crowley gate installed right the first time? Call (877) 610-2993 now. A live person answers 24/7. We’ll schedule a free measure, walk your property line, and hand you a written price before any work starts. No trip charge inside the county. No surprises at the door. Just a gate that stays plumb through the next drought and the next flood.