Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Mulvane, KS
When a gate won’t open at 6:30 on a weekday morning, you don’t need a phone tree. You need someone who knows Mulvane, knows what your gate looked like before it started sagging, and will actually pick up the call. Gate repair in Mulvane usually runs $185 to $390 for hinge and realignment work, and $340 to $780 when an automatic opener is involved. Most Mulvane calls get a same-day visit, and the price is quoted and agreed before a single tool comes off the truck. Call (877) 610-2993 and a live person answers, any hour, any day.
Why Mulvane Homes Are Different
Mulvane sits on the open south-central Kansas plain, which means there’s not much between your gate and the wind. Prevailing southerly gusts push on gate panels year after year, and that steady pressure eats hinge pins and loosens post footings faster than you’d think. Then there’s the soil. This part of the state is known for expansive clay, and every freeze-thaw cycle heaves it an inch one way and an inch back. Gate posts drift out of plumb every few winters, and a gate that was fine in October is dragging by February because the post moved, not the gate.
The housing stock makes it interesting too. A 1950s ranch near the original downtown grid might have a lightweight ornamental gate that just needs re-hanging. A 2010s tract home on the south fringe often inherited an old farm gate from before the land was platted. We see the full range in a single week, and that mix is why Mulvane repair calls don’t look like the calls we get in Wichita’s fully suburban zip codes. Here, we’re fixing gates that were built for cattle and now have to hold up to daily car traffic and an automatic opener.
Gate Repair in Mulvane
Gate repair in Mulvane is its own animal because the gates here fall into two camps: residential gates on newer subdivision homes, and leftover agricultural gates on acreage lots east and south of town. The subdivision gates fail because they were undersized from day one. The farm gates fail because they were never meant to be automatic. Either way, we repair before we replace, and we weld on site so the gate stays in your driveway. Hal Gatewood has been fixing gates since 2001, and he still runs the shop himself. If your gate sags, drags, won’t latch, or the opener stopped responding, call (877) 610-2993 and he’ll talk you through what you’re actually looking at. You can read more about our repair approach on the Gate Repair page.
Electric Gate Repair
Electric gates in Mulvane fail in predictable ways: a builder-grade operator that was undersized from day one, a control board fried by a storm surge, or a safety sensor that never got wired correctly. We service nine major brands, including Linear, Viking, and DoorKing, and we repair the operator in place rather than yanking the whole system. On newer subdivisions near the rural edge, we regularly replace builder-grade units that never had the conduit for a safety photocell to begin with. Electric gate repair runs $340 to $780 when the operator board, receiver, or safety sensors are involved.
Automatic Gate Repair
Automatic gates need more than a working motor. They need proper post footings, correctly aligned rack and pinion, and loop detectors that actually see your vehicle. In Mulvane, where clay soil shifts every few winters, a slide gate installed without allowance for soil movement will bind and strip its rack. We fix the operator, and we also fix the cause: the post that moved, the conduit that was skipped, the footing that was too shallow. On acreage lots around Mulvane, we frequently upgrade pin-hinge farm gates to automation with heavier posts and proper safety edges. Full automation retrofit on an existing farm gate starts around $950 and goes up from there based on the gate’s weight and the power run.
Hinge & Post Repair
A gate sags in the hinge post, not in the middle. That’s where we start. In Mulvane’s older ranch neighborhoods and on rural acreage, we see hinge posts that were set in a bag of quick mix forty years ago and have finally let go. We excavate, set a deeper footing, weld or bolt new hinges, and square the gate back to the post. A hinge or post repair typically runs $185 to $390, depending on whether we’re digging the post or just welding and shimming. For the oversized square-tube farm gates common east of town, we source hardware from agricultural co-ops because standard residential hinge bolts don’t fit that tubing.
Gate Realignment
Many Mulvane gates just need realignment, not replacement. A gate that scrapes the ground, won’t latch, or swings open on its own has a geometry problem. We reset the hinge pins, shim the post, or move the latch plate, and gate realignment with latch adjustment usually lands between $160 and $310. On rural gates retrofitted from manual to automatic, realignment often means upgrading the post before the operator goes in. Fix the panel without the post and you’ll fix it twice.
My builder-installed gate operator in a newer Mulvane subdivision stopped working after two years. Is this common?
Yes, and it’s almost always the install, not the operator. Builders put in the cheapest unit that met code, skipped the conduit for safety photocells, and set the post footings too shallow. We see it regularly in the tract subdivisions around Mulvane. The fix is usually a proper footing, new low-voltage conduit, and an operator sized for the actual gate weight. Call (877) 610-2993 and Hal will tell you what you’re dealing with.
I bought a rural acreage property east of Mulvane with an old farm gate. Can I add an automatic opener without replacing the whole gate?
Usually, yes, with one caveat: the post has to hold up. Farm gates on acreage east of Mulvane are often square-tube steel with pin hinges sized for cattle operations. The gate itself is fine, but the post and footing were never designed for the repeated torque of an automatic opener. We dig and pour a deeper footing, swap in the proper hinge hardware, and only then mount the operator. For an exact quote, call (877) 610-2993, estimates are free.
Gate Installation in Mulvane
We install driveway gates, pedestrian gates, swing gates, and sliding gates throughout Mulvane and the 67110 ZIP. From the older ranch homes near the original downtown grid to the newer acreage lots being carved out on the south and east edges of town, every install starts with the same question: what’s the wind going to do to this gate for the next twenty years? A gate installed in Mulvane has to survive open prairie gusts and clay soil heave, so we set posts deeper and use heavier hardware than a suburban job in Wichita would call for. The price is quoted and agreed before any work starts, so there’s no invoice bigger than the estimate at the end. You can read more on our Gate Installation page.
Driveway Gate Installation
Driveway gates are the most common install we do in Mulvane, and they range from ornamental steel on newer subdivision entries to heavy tube-steel farm gates on acreage parcels. We handle single gates, double gates, and custom widths. A single driveway swing gate on new posts typically runs $1,200 to $2,800 installed, depending on width, material, and whether it’s automated. On exposed acreage without windbreaks, we add cross-bracing and heavier hinge hardware so the gate doesn’t rack within a season or two.
Sliding Gate Installation
Sliding gates are the right answer when a driveway slopes or when there isn’t room for a gate that swings into the yard. In Mulvane, we install cantilever sliding gates that ride above the ground, which matters because the clay soil here heaves through freeze-thaw cycles and can foul a ground-track system every winter. A sliding gate starts around $2,200 and can go to $5,000 or more for heavy steel with an opener. We also handle the automation side if you want the gate motorized from day one.
Pedestrian Gate Installation
Pedestrian gates need to be hung right the first time, because a gate that drags on the ground gets hit twice a day and fails fast. Pedestrian gates in Mulvane run $400 to $1,200, and we install walk gates to match existing fencing, whether that’s chain-link, wood, or ornamental metal. On Mulvane properties with brick-framed garden entries, we can weld custom hinge plates on site so the gate fits the opening exactly.
How fast can you install a gate in Mulvane?
Most standard gate installations in Mulvane can be scheduled within one to two weeks, and the install itself usually takes one or two days once materials are on site. Custom gates or farm gate retrofits may take longer if we need to source from an agricultural co-op. Call (877) 610-2993 and we’ll give you a straight answer on timing.
How much does a new gate cost in Mulvane compared to Wichita?
Gate installation in Mulvane runs similar to Wichita, though acreage properties with heavier farm gates and longer drives can add to the cost because of materials and post depths. A basic single driveway gate starts around $1,200. A double gate with automation is typically $2,400 to $5,500. We quote a firm price before any work starts. Call (877) 610-2993 for a free estimate.
Gate Motor & Opener in Mulvane
Gate motor and opener work in Mulvane comes down to one thing most of the time: the operator was undersized for the gate it’s pushing. On subdivision entries, the builder put in the cheapest unit that met code. On acreage lots, a previous owner bolted an opener onto a farm gate that weighs twice what the motor was rated for. Either way, we diagnose the fault, repair the operator in place when it makes sense, and replace it when it doesn’t. We service Linear, Viking, Ghost Controls, and DoorKing units, plus five other major brands. Motor or opener repair typically runs $120 to $350 depending on the fault and brand. You can read more on our Gate Motor & Opener page.
Opener Replacement
When an opener has failed beyond repair, we replace it with a unit sized for the actual gate weight, not the one that was there before. In Mulvane’s windy conditions, an undersized opener works twice as hard and dies twice as fast. A straight opener replacement on a standard residential gate usually lands between $340 and $780, including mounting, wiring, and testing of the safety sensors.
Safety Sensor Repair
Every automatic gate in the 67110 ZIP has to meet the UL 325 safety standard, which means entrapment protection: photo-eyes, an edge sensor, or both. On Mulvane properties where the builder skipped the conduit, the sensors were never wired at all, and that’s a code violation and a safety problem. We open the trench, run the conduit, and set the sensors properly. Sensor wiring and realignment runs $120 to $350 depending on how much trenching is involved.
Loop Detector Service
A loop detector is what tells your slide gate that a vehicle is in the path and keeps it from closing on the truck, the mower, or the grandkid’s bike. Mulvane’s clay soil and open exposure mean slide gates already work hard against wind and heave; a missing or failing loop detector makes them unsafe on top of it. Loop detector replacement typically runs $180 to $400, and we cut the loop, wire it to the operator, and test it with a vehicle before we leave.
Are automatic gates in Mulvane required to have photo-eyes or edge sensors?
Yes. Any automatic gate installed in the 67110 ZIP has to meet the UL 325 safety standard, which means entrapment protection: photo-eyes, an edge sensor, or both depending on gate type and site conditions. We install and test every safety device, and we won’t leave a gate operating without them. Call (877) 610-2993 if your opener is running without working sensors.
Why does my slide gate close unexpectedly in Mulvane?
Nine times out of ten it’s a failing loop detector or a misaligned safety sensor. The wind and clay heave around Mulvane knock sensors loose and crack loop wiring over time. If your slide gate closes unexpectedly or won’t hold open, call (877) 610-2993 and we’ll trace the fault the same day.
Gate Access Control in Mulvane
Gate access control in Mulvane typically runs $350 to $1,100 for a complete keypad or intercom install, with full smart-access systems on acreage properties ranging from $1,400 to $3,200. Most Mulvane jobs are quoted in writing before we touch a wire. Mulvane sits in a strange spot, half suburban and half rural, which means we’re retrofitting keypads onto brand-new subdivision gates one day and welding adapter plates onto 1980s farm gates the next. The common thread is that the existing gate is rarely ready for the access system out of the box. Call (877) 610-2993 and we’ll tell you exactly what your setup needs. More detail is on the Gate Access Control page.
Keypad Entry
A keypad access system in Mulvane typically runs $425 to $950 installed, depending on whether we’re wiring a standalone keypad or integrating it with an existing opener. Most Mulvane customers want a keypad that survives Kansas weather, which means a sealed unit with a protective hood, not the cheapest thing on the shelf. We mount it at the right height for both car windows and walk-up use, and we test it in front of you before we leave.
Phone Entry
Phone entry systems use your cell phone to open the gate through a call or app, and those installs in Mulvane generally start around $475 and run up to $1,300 depending on the system. This is a good fit for Mulvane acreage properties where you don’t want to hand out gate codes to every delivery driver or service tech who needs in. You can open the gate remotely, see call logs, and change access instantly from your phone.
Card Reader
Card reader access control is more common on Mulvane properties with multiple users or small business entrances, and those systems typically run $600 to $1,700 installed. We work with DoorKing and Viking card systems most often here, because those brands hold up to the wind and temperature swings better than entry-level options. If you’re upgrading from a keypad to card access, we can usually reuse your existing gate operator and save you the cost of replacing the whole setup.
Does gate access control cost more in Mulvane than in Wichita?
No, our pricing is the same across the county. What changes the cost in Mulvane isn’t the location, it’s the condition of the gate. Older agricultural gates need more labor for custom mounting, and homes with outdated wiring sometimes need a new low-voltage run. There’s no trip charge inside the county. Call (877) 610-2993 for a quote.
What does a full access control installation include in Mulvane?
A full installation includes the keypad, card reader, or phone entry hardware, mounting to your existing gate post or frame, wiring and electrical connections to your opener, programming, and testing. We confirm the gate opens and closes properly on automatic cycles before we leave, and we quote the entire job in writing first. Call (877) 610-2993 for a free estimate.
Gate Parts & Welding in Mulvane
If your gate sags, drags, or won’t latch in Mulvane, the fix usually comes down to a part or a weld, not a whole new gate. Gate parts and welding here typically runs $120 to $480 depending on whether we’re replacing hinges on a chain-link swing gate or cutting out a rotted post on a farm gate east of town. We keep the work in your driveway, on-site, because you shouldn’t have to haul a 300-pound gate to a shop. Hal welds on site, and he’s been doing it since 2001. The full breakdown is on the Gate Parts & Welding page.
Hinge Replacement
A gate sags in the hinge post, not in the middle, and that is where we start. On older ranch homes near the original downtown grid and the 2000s tract subdivisions to the south, heavy ornamental iron and chain-link gates wear through residential hinge barrels in five to eight years. In Mulvane specifically, the sustained southerly winds push against gate panels day after day, which accelerates that wear on the top hinge first. Hinge replacement on a standard residential chain-link gate runs $120 to $260, including heavy-duty hinges and realignment.
Post Replacement
The expansive clay soils around Mulvane heave through every freeze-thaw cycle, and we regularly find gate posts shifted two to three inches out of plumb by late winter. Fix the panel without the post and you’ll fix it twice. Post replacement runs $180 to $450 depending on post size, depth, and whether we’re digging out old concrete or setting new. For the square-tube farm gates east and south of town, post replacement often means welding a custom sleeve or setting a heavier post than what was there before.
Rail Repair
Top and bottom rails take the most abuse on any swing gate, but in Mulvane the wind means rails flex constantly, not just when the gate moves. Weld fatigue at the rail-to-stile joints is common on steel tube gates that have been up since the property was agricultural. Rail repair and on-site welding run $150 to $380 for most single-gate jobs. We cut out the bad section, weld in new steel, and the gate stays on its hinges the whole time.
Custom Welding
Sometimes the right part doesn’t exist because the gate came from a tractor supply catalog in the 1980s. On recently platted acreage lots in the 67110 ZIP, we frequently find leftover farm-supply gates: square-tube steel with pin hinges and oversized tubing that residential gate hardware simply doesn’t fit. Custom welding, like fabricating hinge plates for an oversized farm gate, runs $220 to $480. We fabricate the brackets on-site to match the existing steel, so you keep the gate you already have.
Do you offer emergency welding service in Mulvane?
We answer the phone 24 hours a day and can often get to a broken gate in Mulvane the same day or the next morning, depending on the call time. If the gate is off its hinges and leaving livestock loose or a yard unsecured, that’s a priority call. Call (877) 610-2993 for an urgent repair quote.
Is your work in Mulvane covered by a warranty?
Every job carries the 90-Day Done Right Promise in writing. If it’s not done right, Hal comes back and makes it right, no charge and no argument. That’s stamped on the invoice, not buried in fine print. Call (877) 610-2993 and you’ll get the quote, the promise, and the work from one locally owned name.
Brands We Service in Mulvane
We service nine major gate brands, including Linear, Viking, Ghost Controls, and DoorKing. We keep common boards, remotes, and safety sensors on the truck, which means most Mulvane opener repairs happen in one visit, not two. See our brands for the full list.
Pricing for Gate Repair in Mulvane, KS
| Service | Typical Range in Mulvane |
|---|---|
| Hinge or post repair | $185 - $390 |
| Gate realignment and latch adjustment | $160 - $310 |
| Electric gate repair (board, receiver, sensors) | $340 - $780 |
| Full automation retrofit on existing farm gate | $950 and up |
| Motor or opener repair | $120 - $350 |
| Single driveway swing gate (new install) | $1,200 - $2,800 |
| Double swing gate (new install) | $2,400 - $5,500 |
| Sliding gate (new install) | $2,200 - $5,000 |
| Pedestrian gate (new install) | $400 - $1,200 |
| Keypad install or replacement | $425 - $950 |
| Phone entry system install | $475 - $1,300 |
| On-site welding repair | $120 - $480 |
What pushes the price up in Mulvane is usually the age and condition of the existing gate. An old farm gate with oversized steel takes custom welding and heavier hardware, while a newer subdivision gate stays on the lower end. Every price is quoted and agreed in writing before any work starts, so the number on the invoice is the number you approved.
Neighborhoods We Serve in Mulvane
We cover all of Mulvane and the surrounding 67110 area. Most repair calls inside the city get a same-day visit, and we don’t charge a trip fee anywhere in the county.
- Downtown Mulvane and the original grid streets around Main
- Subdivisions east of K-15
- Newer fringe developments on the south edge of town
- Acreage properties south of town toward the county line
- Mulvane school district boundary areas
Service Area - Cities Near Mulvane
Gatewood Fence & Gate serves Mulvane, KS and the surrounding communities, including Derby, KS, Haysville, KS, Wichita, KS, Wellington, KS, and Andover, KS. Scheduling runs from our Wichita office, so a Mulvane trip is a short drive, not a route we have to plan around.
Serving Mulvane, KS - Our Local Coverage Area
Gatewood Fence & Gate crews serve Mulvane and the communities around it; dispatch is coordinated from our Wichita office. The map shows the Mulvane coverage area; if your address is on it, we can help.
Also serving nearby: Mulvane, KS, Derby, KS, Haysville, KS, Wichita, KS, Wellington, KS, Andover, KS.
FAQs About Gate Repair in Mulvane
We can typically reach most of Mulvane the same day you call. The crew works from the Wichita office, and the drive down K-15 is short. If the gate is stuck open or leaving a fenced yard unsecured, we treat it as urgent and move it to the front of the schedule. Call (877) 610-2993 and a live person will tell you when we can get there.
We repair both, and in Mulvane the old farm gates are a big part of the work. On acreage lots carved from former agricultural land, leftover square-tube steel gates with pin hinges are common. Standard residential hardware doesn’t fit them, so we source from agricultural co-ops and weld adapters on site. Call (877) 610-2993 and describe what you have, we’ll tell you straight what it needs.
It’s the post, not the gate. Mulvane’s expansive clay heaves through every freeze-thaw cycle, and a gate post set a few feet deep will gradually lean away from the gate’s weight. The gate itself is rarely bent. We excavate the post, set a deeper footing, realign the hinge pins, and the gate swings clean again. For an exact quote, call (877) 610-2993, estimates are free.
Need a gate repaired, installed, or automated in Mulvane? Call (877) 610-2993 and you’ll get a live person, a straight answer, and a price quoted before any work starts. Hal Gatewood’s name is on the shop, and he means it.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Mulvane Customers Say
"Fitted a keypad and an intercom so my mother can let carers in without coming down the drive. He set it up and then made her practise with it until she was comfortable."
- Lucinda Marchbanks"Beautiful gate and solid work. The build took about three weeks longer than the estimate because he was waiting on the ironwork, and I would rather have known that at the start than found out along the way."
- Beatrice Nwosu"Operator had died and the manufacturer no longer makes the board. Rather than sell me a whole new system he found a compatible unit and adapted the mount. Saved me a great deal of money."
- Salvador Arredondo