Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGhost Controls Gate Repair in Fresno, CA | Gatewood Fence & Gate
We repair Ghost Controls gate openers across Fresno, from Calwa to the Bullard corridor. If your Ghost Controls swing or slide gate has stopped mid-cycle, won’t respond to the remote, or grinds when it moves, we fix it on site, usually in one visit. What makes our Ghost Controls work different here is simple: we know which parts this valley’s Tule fog and 110°F heat destroy first, and we stock for it. Call (877) 610-2993 and a live person answers, any hour.
Why Fresno Residents Choose Us for Ghost Controls Service
We run Ghost Controls sales & service as an independent shop. That matters because we are not factory-authorized and we do not pretend to be. What we are is familiar: we have rebuilt Ghost Controls DTP swing arms, AXS slide motors, and G5 operators in driveways from East Thomas Avenue to Sequoia-Kings Canyon Freeway frontage. Hal Gatewood has been at this since 2001, and he is the one who signs the work. If a previous installer left a board wired wrong or a gear packed without grease, Hal is the guy who finds it and says so plainly.
Fresno homeowners call us because a live person picks up the phone at 2 a.m. with a gate stuck open. Because we weld on site instead of hauling your gate to a shop. And because every job carries a written 90-Day Done Right Promise: if it is not done right, one call brings us back.
Common Ghost Controls Gate Repair Problems We Solve in Fresno
- Fog-oxidized limit switch terminals on DTP series. December through February, Tule fog keeps humidity near 100% for weeks. The exposed limit switch terminals on DTP1 and DTP2 units corrode green, the limit cams misread, and the gate stops short or over-travels into the post. We sand, re-seat, and seal the terminals so the gate cycles clean.
- Heat-welded relay contacts on AXS and SLT slide motor boards. A 105°F heat soak bakes the relay on the AXS/SLT control board until the contacts fuse. The gate dies mid-track and won’t draw current. We replace the relay or the board, then check the enclosure venting so the next summer is not a repeat.
- Backup batteries that fail after one summer and one fog season. Fresno heat shortens a Ghost Controls G5 or DTP backup battery’s rated life by 30-40%. Then winter fog oxidizes the spade terminals so the charger stops working entirely. The first power flicker leaves you stranded. We replace the battery and the terminals, and we tell every customer to have it checked each fall.
- Cracked plastic gear or coupler inside worm-drive swing arms. When a warped wood panel or a misaligned hinge adds torque, the plastic gear inside the Ghost Controls swing arm cracks. We see this often on mid-century retrofits in Calwa and zip 93706 where gates were never built for automation. We align the hinge, free the panel, and replace the gear.
- Rust-seized manifold seams on slide gate arms. Along East Thomas Avenue and the Dwight David Eisenhower Memorial Freeway frontage, old Ghost Controls arms hold rust at the manifold seam. That pinhole pattern shows up more in Fresno than any city south of the fog line. We weld the seam, grind it clean, and repack the hub so the gate stops binding.
Ghost Controls Service in Fresno: What Local Conditions Mean for Your Equipment
Fresno is not Long Beach and it is not Riverside. The San Joaquin Valley runs a two-season stress cycle no coastal city faces: months of dense ground-level Tule fog from December through February, then triple-digit heat from June through September. Each season attacks a different part of your Ghost Controls opener. The fog saturates iron and steel hardware, corroding limit switch terminals, battery spade connectors, and uncoated arm seams. The summer heat bakes control boards, drains backup batteries, and thermally expands steel slide tracks until wheeled gates jam. A Ghost Controls opener that works flawlessly in a coastal climate can fail here twice as fast if the previous installer did not account for either extreme. That is why our Fresno techs check the backup battery every fall without fail: the fog will corrode the terminals over winter and the preceding summer has already shortened the battery’s life by a third or more. If you live off Sequoia-Kings Canyon Freeway in Calwa or anywhere in the valley floor, your equipment fights both seasons every year.
Ghost Controls Models & Products We Service in Fresno
We service every Ghost Controls line still in the field: the DTP Series (DTP1, DTP2) single and dual swing gate operators, the AXS Series heavy-duty slide gate operators, the SLT Series (SLT1, SLT2) linear and slide operators, and the G5 Series (G5, G5D) residential swing operators. We stock OEM control boards, limit switches, and remote receivers for fast Fresno turnaround. When a battery or gear is a wear item and a quality aftermarket part gets you running faster at equivalent spec, we use it and tell you exactly what went in. For DTP or AXS units over eight years old with board, gear, and housing corrosion from fog cycles, we lay out the real math on repeated repairs versus a new operator. We let you decide. We do not push replacement for its own sake.
Ghost Controls Service Pricing in Fresno
Most Ghost Controls repair visits in Fresno land between $180 and $340, depending on the part and the amount of rust remediation involved. A simple limit switch clean-and-seal runs at the low end. A burned relay on an AXS slide board with enclosure venting work runs higher. We quote the price before any work starts, and that price is the price. No trip charge inside the county, $40 off any repair over $200, and a free second opinion on any written estimate. Seniors and veterans get a permanent 10% discount. Call (877) 610-2993 for a free estimate, and we will tell you over the phone what to expect.
Serving Fresno, CA - Our Local Coverage Area
We’re based in the Fresno area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Ghost Controls Gate Repair in Fresno
Tule fog condenses on the exposed limit switch terminals on DTP units. The oxidation makes the limit cams misread, so the gate stops at the wrong point, often around 45 degrees. We sand and re-seat the terminals and seal them against the next fog season. Call (877) 610-2993 and we can usually get it cycling same day.
Yes. The heat shortens the battery’s rated life, and the fog oxidizes the spade terminals so the charger stops working. We replace the battery, clean or replace the terminals, and test the full charge cycle before we leave. We recommend a fall battery check every year in Fresno.
We do. We weld on site, in your driveway. If your swing arm is pulling away from a rusted manifold seam or the gate is binding on a seized hinge post, we repair the metal rather than replacing the gate. That is the whole point of our shop: fix what is fixable first.
Once a year, and the timing matters here. Service it in early fall, before the fog settles in. That lets us clean the corrosion from the previous winter, check the battery, and re-grease the track before the cold moisture returns. Slide gates on the agricultural fringe of Fresno with long pipe-rail runs need this more than anything.
Yes. The DTP board has an input for external access control, and we can wire a keypad, card reader, or phone-based entry system to it. Many Bullard-area gated communities run older openers with newer entry systems retrofitted. We handle the wiring and the programming.
Service Areas Near Fresno
We cover Fresno and the surrounding valley communities. If your Ghost Controls opener is acting up in Fresno service area neighborhoods like Calwa or along the 93710, 93711, 93712, and 93714 zips, we will be there. We also run Ghost Controls service in Long Beach and Ghost Controls service in Riverside for customers with properties in both places.
Book Your Ghost Controls Service in Fresno Today
Call (877) 610-2993. A live person answers, day or night. We will talk through what your gate is doing, give you a straight price, and get someone to your driveway fast. Hal’s name is on the shop and on the work, and that is the oldest guarantee there is.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Fresno since 2001.