Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Beverly Hills, CA
Gate repair in Beverly Hills usually means one of three things: a wrought-iron hinge post rusted through from nightly marine-layer moisture, an automated operator that lost its calibration on a graded hillside driveway, or a sliding gate grinding grit after a Santa Ana wind event. Most repairs here run between $180 and $600, and we handle them same-day in most cases because our crews work Beverly Hills locally from our Los Angeles office. Call (877) 610-2993 and a live person answers, not a recording.
Why Beverly Hills Homes Are Different
Beverly Hills sits five to six miles inland from the Pacific, and that geography shapes every gate we touch. The marine layer rolls in most nights, condensing on cold iron and steel, so surface rust on hinges, operator brackets, and decorative scrollwork is a year-round problem here, not a rainy-season one. Then the Santa Ana winds blow grit and leaf litter into roller tracks and gear assemblies, especially on long estate driveways where gates wait months between service calls. By the time an absentee owner notices a gate dragging, the operator has usually been fighting it for months.
The housing stock splits sharply along Santa Monica Boulevard. South of it, in the 90211 and 90212 flats, Spanish Colonial and Mediterranean homes sit on tighter lots with sliding or single-swing gates. North of Sunset, in 90210, you get grand estates built from the 1920s through the 1980s, many still holding original ornate wrought-iron gates that demand restoration metalwork rather than replacement. And in the hills, driveways often run on a real grade, which means swing gates need grade-compensating hinges or ram-style actuators calibrated for slope clearance. A technician trained only on flat suburban installs will misdiagnose that every time.
Gate Repair in Beverly Hills
Gate repair in Beverly Hills comes down to knowing what you’re looking at. A sagging gate on Canon Drive is usually a hinge post problem, not a panel problem. A gate that drags on a hillside off Mulholland is usually a post that shifted, not a weak motor. And a sliding gate that binds after wind in the flats is usually debris packed into the track, not a failed operator. We fix the actual cause, in your driveway, with on-site welding when the job calls for it. Our Gate Repair work always carries the 90-Day Done Right Promise in writing.
Electric Gate Repair
Electric gate operators in Beverly Hills run hard. Salt air eats at circuit boards and connectors, and Santa Ana winds push grit into operator housings. We service nine major brands including Linear, Viking, and DoorKing, and we stock common boards, capacitors, and limit switches so we’re not waiting on a distributor when your gate won’t open. Most electric gate repairs in Beverly Hills are diagnosed and fixed in one visit, and diagnosis with board replacement runs $250 to $650.
Hinge & Post Repair
A gate sags in the hinge post, not in the middle. That’s where we start. The marine layer works on hinge posts year-round here, rusting the base where steel meets concrete footing. We cut out the rotted section, weld in new steel, and re-seat the gate so it swings true. A basic hinge and post repair in Beverly Hills runs $180 to $340. If the post has shifted in the footing, we re-set it and re-anchor it. Fix the panel without the post and you’ll fix it twice.
Gate Realignment
Gates drift out of alignment for a dozen reasons: settling posts, worn hinge bearings, wind-loading on a big iron panel, or a car bumping the gate. On Beverly Hills hillside properties, the grade itself works against you. A gate that was aligned two years ago may now drag because the ground settled a quarter inch. Realignment on a flat lot runs $180 to $300; on a graded hillside driveway, $300 to $600 because of the additional calibration involved. If the real issue is below-grade movement, we’ll tell you that instead of just nudging the board and leaving.
Why does my ornate wrought-iron gate in the Beverly Hills flats develop surface rust even when it rarely rains?
Beverly Hills sits five to six miles from the Pacific, and the marine layer rolls in most nights, condensing on cold iron and steel. That moisture, combined with salt in coastal air, accelerates oxidation year-round even with low annual rainfall. We use stainless fixings on every repair here, and painted steel gets proper priming and sealing. Call (877) 610-2993 and we’ll assess your gate’s rust in person.
My swing gate on a hillside driveway in 90210 drags partway open. A previous technician said the motor was weak. What’s actually happening?
Most likely the post has settled and the grade-compensating hinge geometry is now off, so the gate drags on the uphill arc. This is common on Beverly Hills hillside estates where original footings shift over time. The motor is rarely the problem; the alignment is. We re-set the post, correct the geometry, and recalibrate the operator’s limit switches so the gate clears the slope without stalling.
Gate Installation in Beverly Hills
Gate installation in Beverly Hills runs $4,800 to $18,000 for most automated driveway gates, with custom estate work in the hills north of Sunset often landing between $15,000 and $40,000 depending on fabrication, operator hardware, and access control integration. We’re a locally owned, owner-operated shop, and we build gates that fit this city’s specific properties: long graded driveways, 1920s wrought-iron originals, and security systems that have to work with estate staff. Every Gate Installation quote is written and agreed before any work starts.
Driveway Gate Installation
New driveway gates in Beverly Hills start around $6,500 for a single swing gate with a solid operator, and go up from there depending on span, material, and automation. In the flats south of Santa Monica Boulevard, where lots are tighter, many homes in 90211 and 90212 need sliding gates to save space. We install those with rack-and-pinion drives sized for the gate’s weight, not the cheapest motor that fits. A driveway gate here is a daily-use machine, and it has to open and close thousands of times without complaint.
Swing Gate Installation
Swing gates are the dominant style in Beverly Hills, and the hills north of Sunset are a different world than the flats. A gate on a 5 to 10 percent grade needs grade-compensating hinges or a ram-style actuator, not a standard underground operator. We set post footings below the shifting topsoil so heavy steel panels don’t drag after a year. Double swing gates on graded estate driveways start around $12,000 and run to $25,000 or more with hydraulic operators and custom fabrication. This is the single most common installation mistake we see from crews trained on flat suburban work.
Pedestrian Gate Installation
Pedestrian gates in Beverly Hills are usually built to match the driveway gate and the house. We fabricate them to width and height, install them with self-closing hinges and magnetic locks or keypad entry where needed, and make sure the latch alignment is dead-on from day one. Pedestrian gates run $1,800 to $4,000 depending on size and hardware. A pedestrian gate that sags three months later drags on the strike plate and stops latching; that’s a hinge-post problem, and we set posts deep enough that it doesn’t happen.
How does the grade of my Beverly Hills driveway affect gate operator choice?
A 5 to 10 percent grade changes everything. Standard swing gate operators assume a level ground plane. On a slope, the gate’s weight shifts toward the downhill side, so the operator works harder and hinges wear unevenly. We install grade-compensating hinges or ram-style actuators on graded Beverly Hills driveways, and we recalibrate limit settings for slope clearance. If your gate drags on a hill, the operator choice was wrong for the site.
What is the difference between a sag correction and a full gate replacement in Beverly Hills?
A sag correction fixes the hinge post and geometry so the gate hangs true again. A full replacement replaces the gate panel. If the panel is still sound, we’ll almost always repair the post, replace the hinges, and reinforce the frame; that runs $900 to $2,500 versus a $6,500-plus replacement. We only recommend replacement when the panel itself is structurally gone. Call (877) 610-2993 for an honest assessment.
Gate Motor & Opener in Beverly Hills
Gate motor and opener work in Beverly Hills is different from most of Los Angeles. This city has one of the highest concentrations of custom-fabricated, high-end automated estate gates in the country: ornate wrought-iron and steel pieces integrated with multi-camera access control, video intercoms, and dual-lane entries. A motor replacement here usually means fabricating a bracket to fit a 1920s iron gate without altering its architectural character, not just unbolting an off-the-shelf arm. Our Gate Motor & Opener service covers all nine major brands we’re certified on.
Motor Repair
Most Beverly Hills gate motor failures we see are not dead motors. They are worn hinge posts, corroded brackets, stripped rack-and-pinion gears, or debris packed into the track. We repair what other companies want to replace. A straightforward motor repair typically runs $180 to $340 for diagnosis and parts on common failures like limit switches, capacitors, or photocell alignment. Hal fixes the gate in your driveway rather than hauling it off or swapping parts that don’t need swapping.
Motor Replacement
When a motor does need replacement, Beverly Hills nearly always requires custom fabrication. A 1970s FAAC operator on an original wrought-iron gate cannot be swapped for a modern unit by bolting on a stock bracket. The mounting points don’t line up, the gate weight is different, and the geometry of a hand-forged panel is never exactly square. Motor replacement with a premium operator like a LiftMaster LA500, BFT, or FAAC runs $1,400 to $3,200 installed, depending on gate weight, grade, and bracket fabrication. We weld brackets on site and configure the new operator to the gate’s specific swing, weight, and grade.
Slide Motor Service
Slide gates in Beverly Hills take a beating from Santa Ana wind events. Grit and fine debris drive into roller tracks and gear assemblies, causing loop detector faults and limit-switch misreads. We see this across the flats south of Santa Monica Boulevard on Spanish Colonial and mid-century properties with sliding driveway gates. Often the dead control board diagnosis from another company is actually a debris-packed gear rack. We service Linear, Viking, and DoorKing slide systems, and we clean, reset, and test before we ever recommend replacing electronics. That’s the difference between a $190 service call and a $1,400 board swap that doesn’t fix anything.
Why does my estate gate in the hills drag only on rainy mornings?
Rainy mornings mean moisture has gotten into wood, soil, or a rusting post footing, and the gate panel is expanding or the post is moving just enough to drag. On a grade-compensating setup in the 90210 hills, a gate that only drags when wet usually has a hinge post that shifted slightly, and moisture is the tipping point. The fix is resetting the post and recalibrating the operator’s slope clearance.
Our dual-lane estate entry has one gate that opens slower than the other. Is that a limit-switch problem?
Not usually. On dual-lane Beverly Hills entries, one gate opening slower almost always traces back to uneven load: one gate is heavier, one hinge post has shifted, or one operator is older with a wearing capacitor. Limit switches are binary; they don’t control speed. We test actual amp draw on each motor, check the post footings, and compare the two sides before recommending any fix.
Gate Access Control in Beverly Hills
Gate access control in Beverly Hills usually comes down to one of two calls: a keypad that stopped reading codes, or an estate gate that won’t open when the property manager’s car pulls up. Most jobs we handle in the 90210 and 90212 ZIPs are diagnosed same-day and repaired on the spot, because we keep common failure parts on the truck. Our Gate Access Control work often involves coordinating directly with estate managers and private security firms rather than homeowners.
Keypad Entry
Keypad entry in Beverly Hills fails differently than in Santa Monica or Culver City. The daily marine-layer moisture seeps into unsealed keypad housings and corrodes the membrane contacts within a single season. Symptoms are intermittent: the code works at noon but not at 9 p.m. when the housing cools and condensation forms. Keypad replacement runs $350 to $750 depending on whether it’s standalone or integrated with a video intercom system. We use weather-sealed enclosures and dielectric grease on the contacts; big-box keypads don’t last here.
Card Reader
Card readers on Beverly Hills estate gates are usually tied to a multi-camera access system and managed by an estate manager or private security firm. We work with them directly. The most common failure is contact corrosion on the reader face and moisture intrusion into the pigtail wiring behind the reader. A reader that works for one car but not another usually has a failing contact block. Card reader replacement runs $400 to $900 per reader, and we carry replacement modules for Linear and DoorKing readers on the truck.
Video Intercom
Video intercom systems on Beverly Hills estate gates are often custom-integrated: gate camera, house phone, smartphone app, and sometimes a guard station. When the video feed drops but audio works, the issue is usually a corroded RJ45 connector or a failed power injector at the gate operator enclosure. Video intercom troubleshooting and repair runs $200 to $500 on most jobs. We troubleshoot the whole chain, from the camera at the gate to the monitor inside the house, and we retrofit older analog intercoms to IP-based systems without tearing up the driveway.
Why does my Beverly Hills gate keypad work at noon but not at night?
Nighttime condensation. Beverly Hills sits five to six miles from the Pacific, and the marine layer rolls in most evenings. When the keypad housing cools, moisture condenses inside and bridges the contacts, causing intermittent failures. The fix is replacing the keypad with a weather-sealed enclosure rated for coastal exposure. Call (877) 610-2993 and we’ll swap it same-day in most cases.
Do access control systems on Beverly Hills estate gates need entrapment protection?
Yes. Every automated gate in Beverly Hills must have functioning entrapment protection: photo eyes, safety edges, or both. UL 325 standards apply here just like anywhere else in California. Older estates in the flats and hills often have systems that predate current code, with safety edges cracked, sun-baked, or disconnected. We test entrapment protection on every access control service call and replace safety edges that fail.
Gate Parts & Welding in Beverly Hills
Gate parts and welding in Beverly Hills is rarely a simple parts swap. The gates here are heavier, the driveways run on grade, and the ironwork is often original to homes built between the 1920s and 1980s. A hinge that fails on a flat lot in Culver City fails differently on a hillside estate north of Sunset, where post shift throws off the entire swing arc. Our Gate Parts & Welding work is done on site, in your driveway, so the gate’s patina and proportions stay true to the original design.
Hinge Replacement
A gate sags in the hinge post, not in the middle, and that’s where we start. Salt-heavy marine air drifting five miles inland means hinge barrels and pins corrode faster than homeowners expect, especially on the north-facing side of any gate. Hinge replacement runs $220 to $480 per hinge, depending on gate weight and whether we’re fabricating custom strap hinges for an ornate gate or installing reinforced barrel hinges on a standard steel frame. For 1920s estate gates with original decorative hinges, we restore and reinforce rather than replace the whole leaf.
Post Replacement
Post shift is the single most misdiagnosed gate failure in the hills north of Sunset. Driveways on grade push lateral load downhill constantly, and over decades a steel post in concrete can lean just enough to change the entire gate arc. Post replacement runs $650 to $1,850 per post, including concrete removal, new footing, and re-hanging the gate. We use thicker-wall steel and set it deeper than the original footer. Fix the panel without the post and you’ll fix it twice. In 90210, that’s a costly lesson we’d rather save you from.
Custom Welding
Beverly Hills has one of the highest concentrations of custom-fabricated automated estate gates in the country. Ornate wrought-iron and steel pieces integrated with multi-camera access control systems, video intercoms, and dual-lane entry configurations. Nearly every gate is a one-of-a-kind architectural installation requiring bespoke fabrication, not off-the-shelf component swaps. Custom welding is quoted by the job: a scrollwork repair or picket replacement typically runs $180 to $600, while full rail reinforcement on a long slide gate runs $400 to $1,200. Hal welds on site, in your driveway, so the gate’s patina and proportions stay true to the original design.
Can you repair the ornate wrought-iron hinges on my 1920s estate gate without replacing the whole gate?
Yes. We restore and reinforce original hinges rather than replacing entire gate leaves. We cut out cracked or corroded material, weld in matching reinforcement plate, and grind the repair to match the original profile. For decorative forge-welded hinges from the 1920s, we preserve the visible ironwork and reinforce from the back side. A full leaf replacement is almost never necessary for hinge work.
My gate operator was replaced last year but now the gate binds when the Santa Ana winds blow. What’s happening?
The wind isn’t the problem; the debris is. Santa Ana events drive grit, leaves, and small branches into the track and rack-and-pinion assembly on slide gates. If the gate was already marginally misaligned, the added friction binds it. The operator is fighting a mechanical restriction. Show us the gate closing on its own and we’ll show you where it’s failing. Call (877) 610-2993 and we’ll clean, re-align, and test it.
Brands We Service in Beverly Hills
We service and stock parts for Linear, Viking, Ghost Controls, and DoorKing, along with five other major gate brands. Common boards, capacitors, limit switches, and brackets are kept in our Los Angeles office so Beverly Hills jobs don’t wait on a distributor. See our brands page for the full list and what we keep on hand.
Pricing for Gate Repair in Beverly Hills, CA
| Service | Typical range in Beverly Hills |
|---|---|
| Basic hinge and post repair | $180 - $340 |
| Electric gate operator diagnosis and board replacement | $250 - $650 |
| Gate realignment (flat lot) | $180 - $300 |
| Gate realignment (graded hillside driveway) | $300 - $600 |
| Weld and rust repair on ornamental ironwork | $150 - $500 |
| Single swing driveway gate installation | $6,500 - $9,500 |
| Double swing gate on graded estate driveway | $12,000 - $25,000 |
| Pedestrian gate installation | $1,800 - $4,000 |
| Sliding gate installation | $7,000 - $14,000 |
| Gate motor replacement (premium operator, installed) | $1,400 - $3,200 |
| Battery backup addition | $450 - $800 |
| Keypad replacement | $350 - $750 |
What pushes prices up in Beverly Hills is the grade and the custom nature of the work. Hillside driveways need more calibration time, and ornate ironwork needs fabrication, not off-the-shelf parts. Every price is quoted and agreed before any work starts, and it doesn’t change at the door.
Neighborhoods We Serve in Beverly Hills
We cover the full spread of Beverly Hills, from the flats south of Santa Monica Boulevard to the estates above Sunset. Response time is typically same-day for repairs and emergencies, since our crews are coordinated locally from the Los Angeles office.
- Beverly Hills Flats (90211 and 90212)
- Trousdale Estates (90210)
- Coldwater Canyon and the drives off Mulholland
- The Golden Triangle and condo buildings around Wilshire
- Carmelita Avenue and Lexington Road
Service Area - Cities Near Beverly Hills
Our Beverly Hills work often takes us into the surrounding areas. We regularly serve Beverly Hills, CA and the neighboring communities of Century City, CA, West Hollywood, CA, Culver City, CA, Hollywood, CA, and Studio City, CA. Same-day availability applies across this entire service area.
Serving Beverly Hills, CA - Our Local Coverage Area
Gatewood Fence & Gate crews serve Beverly Hills and the communities around it; dispatch is coordinated from our Los Angeles office. The map shows the Beverly Hills coverage area; if your address is on it, we can help.
Also serving nearby: Beverly Hills, CA, Century City, CA, West Hollywood, CA, Culver City, CA, Hollywood, CA, Studio City, CA.
FAQs About Gate Repair in Beverly Hills
In most cases, same-day. Our crews are coordinated locally from the Los Angeles office, which means we’re already working in Beverly Hills and the surrounding areas every day. Emergency calls get priority, and a live person answers the phone around the clock. Call (877) 610-2993 and we’ll give you a real arrival window, not a four-hour spread.
It depends on the scope. Most gate repairs, hinge work, and motor replacements on existing gates don’t require a permit. New installations, post replacements, and work that touches electrical or structural footings may, depending on city requirements. We’ll tell you plainly what your job needs and coordinate with the city if a permit is required. Call (877) 610-2993 and we’ll walk you through it.
We do, regularly. Most Beverly Hills estate gates tie into multi-camera access control systems, video intercoms, and dual-lane entry configurations, and we coordinate directly with estate managers, general contractors, and private security firms on written work scopes, scheduled access windows, and system integration. We test the full system before we leave. Call (877) 610-2993 and ask for Hal.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Beverly Hills Customers Say
"He came out in the snow to get our gate closed after a delivery lorry clipped it, then came back in the spring to do the proper repair when the ground had thawed. Only charged for the second visit."
- Ingrid Solheim"The fence is excellent and it was fairly priced. He is not quick to answer email, so if you need him, ring. He always picks up the phone."
- Rodney Falkenrath"Safety photo eyes on our old gate had been bypassed by whoever serviced it last, which he was genuinely annoyed about on my behalf. Fitted proper sealed ones and wired them the way they should be."
- Otis Redmond