Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Trophy Club, TX
Gate repair in Trophy Club typically costs $190 to $480 for common hinge, post, and alignment work, and most jobs are finished the same day we come out. If your gate is sagging, dragging on the driveway, or refusing to open, call (877) 610-2993 and a real person answers, any hour. We know the neighborhoods around the Country Club well enough to arrive with the right parts on the truck the first time.
Why Trophy Club Homes Are Different
Trophy Club sits on the edge of the Blackland Prairie, where the clay soil expands and contracts with every dry stretch and every gully-washer. That movement twists gate posts out of plumb and cracks concrete footings. We regularly see gates in this area where the hinges look fine but the post has drifted two inches toward the driveway. Fix the panel without re-setting the post and you’ll fix it twice.
The housing stock here is mostly upscale single-family homes built from the 1990s through the 2010s around the Trophy Club Country Club. Wrought-iron driveway gates and decorative community entry gates were standard features in those decades, and a lot of that original hardware is now aging out at the same time: powder-coat finishes are bubbling, automation boards are failing, and hinges are wearing. Add in the HOA’s architectural review process, and a Trophy Club gate repair is never just a parts swap. It’s matching the original spec sheet, coordinating with the board, and doing the job once so you don’t get flagged at the next inspection.
Gate Repair in Trophy Club
Most Trophy Club gate repair calls we handle fall into a few familiar categories: a motor that hums but won’t move the gate, a post that has leaned from clay soil heave, or ornamental iron that has rusted through at the welds. We’re certified to service nine major brands including Viking, Ghost Controls, and DoorKing, and we carry common parts on the truck for same-day fixes. Every repair carries our Gate Repair 90-Day Done Right Promise in writing.
Electric Gate Repair
An electric gate that won’t open, opens halfway, or chirps and reverses usually has a failed control board, a dead battery, or a sensor that’s lost its mind. In Trophy Club we work on Viking, Ghost Controls, and DoorKing openers found throughout the neighborhoods north of 114. We carry common parts on the truck, so many electric repairs in 76262 are done in a single visit. Opener control board replacement typically runs $240 to $480, parts and labor included.
Hinge & Post Repair
Here’s what we see constantly in Trophy Club: the gate sags because the hinge post has leaned, not because the hinge itself wore out. North Texas clay moves. When a post heaves out of plumb, the gate drags on the ground no matter how many times you tighten the hinge bolts. We dig out the old footing, re-set the post in concrete, and weld or rebuild the hinge mount. Post re-set in concrete runs $280 to $520, and hinge replacement or weld repair runs $190 to $340.
Gate Realignment
Realignment sounds small and can be small. But on a heavy wrought-iron gate built in the 90s or 2000s, a quarter-inch drift at the post becomes a two-inch gap at the latch end. We fix the geometry, not the symptom. In Trophy Club where ornamental gates are common, realignment often reveals a cracked concrete pad or a post that’s started to rot at the base. Gate realignment and sag correction typically runs $160 to $310. Full gate weld-and-realign on ornamental iron runs $350 to $750.
How fast can you get to Trophy Club for a gate repair?
Most Trophy Club appointments get scheduled for the same day or next day, and emergency calls come out any hour. A live person answers at (877) 610-2993 around the clock, every day, and can often give you a same-day arrival window on the first call. For urgent jobs like a gate stuck open with kids or pets in the yard, tell the person who answers and we’ll prioritize you immediately.
Why does gate repair in Trophy Club cost more than nearby cities?
It often doesn’t cost more. Typical hinge and post work runs $190 to $340 in Trophy Club, right in line with Roanoke and Keller. What adds cost is the ornamental iron finish work and HOA matching requirements common across Trophy Club subdivisions. Documenting spec hardware and matching a 20-year-old powder coat takes time that a plain no-covenant repair in Haslet doesn’t. The price is quoted before any work begins. Call (877) 610-2993 for an exact quote.
Gate Installation in Trophy Club
Most driveway gate installations in Trophy Club run $2,400 to $7,800 for a standard ornamental iron swing gate with automation, and $4,500 to $12,000 for a sliding gate on a track. We quote that price in writing before any work starts, and it doesn’t change at the door. If you live off Trophy Club Drive or in one of the neighborhoods winding around the Country Club, we’ll schedule a time to walk your property, measure, and write up a free estimate with no pressure.
Driveway Gate Installation
Most Trophy Club homes have ornamental wrought-iron driveway gates, and many are now 15 to 30 years old. When we install a new one, we check the existing posts first. A gate sags in the hinge post, not in the middle, and that’s where we start. If the post has shifted from clay soil movement, we re-set it in a proper concrete footing before we hang anything. A typical driveway gate install here runs $2,800 to $6,500, depending on width, ironwork detail, and whether automation is included.
Pedestrian Gate Installation
Pedestrian gates are common along the side yards and back entries of Trophy Club homes, especially where a walkout leads to a pool or patio. These gates get opened and closed daily, so the hinges and latch hardware matter. We install pedestrian gates with self-closing hinges where HOA rules require them, and we match the finish to your existing fence. Expect $600 to $1,800 for a standard ornamental iron pedestrian gate, installed.
Sliding Gate Installation
Sliding gates need a track, a cantilever system, or a V-track roller setup. On Trophy Club lots with wide driveways or limited swing clearance, a sliding gate often makes more sense. Sliding gates handle the shifting clay better than swing gates in some cases, because the gate rides on a track instead of hanging from a post. We install both track-style and cantilever sliding gates. Plan on $4,500 to $12,000 for a full sliding gate installation with motor and safety edges. You can read more about our full Gate Installation options.
What does a full gate installation include in Trophy Club?
A full driveway gate installation includes measurement, removal and disposal of the old gate if needed, checking and possibly re-setting the posts, hanging the new gate, installing the opener if requested, and adjusting the open and close limits. We also run the power and install safety edges when automation is part of the job. The price is quoted and agreed before any work starts.
Do you help with HOA approval for gate replacement in Trophy Club?
We provide spec sheets, material descriptions, and finish samples for whatever gate you’re installing, and we’ll give you the documentation your HOA architectural review board asks for. We’ve done enough Trophy Club jobs to know what those boards look for. The submission itself is yours to make, but we make the paperwork easy. Call (877) 610-2993 to schedule a free measure and written estimate.
Gate Motor & Opener in Trophy Club
Gate motor and opener repair in Trophy Club typically runs $180 to $340 for most common failures, and we can usually be in your driveway the same day you call. That’s the short answer, and it holds true whether you’re off Trophy Club Drive near the country club or back in one of the neighborhoods tucked along Marshall Creek. Hal answers the phone himself, and every motor job carries our Gate Motor & Opener 90-Day Done Right Promise.
Motor Installation
A new gate motor for a Trophy Club home usually falls between $1,150 and $2,800, installed. The spread comes down to whether you’re putting a simple swing arm on a single ornamental iron gate or running a heavier slide system on a double driveway entry off Indian Creek Drive. We pull the permits your HOA wants to see, match the finish to your existing ironwork, and set the post footing deep enough for our shifting clay.
Motor Repair
Most motor failures in Trophy Club are easier on the wallet than people expect. When a Ghost Controls or DoorKing unit stops responding, it’s often a limit switch, a capacitor, or a gear that stripped rather than the whole motor. We open it up before we quote a replacement. Typical motor repairs run $180 to $340, and we never swap parts that don’t need swapping. Hal would rather weld a bracket than sell you a new operator.
Linear & Slide Motors
Linear motors on slide gates take a beating in North Texas. The clay under your driveway moves, the track shifts, and the motor starts working against itself until a limit switch burns out. In Trophy Club, where many back gates run along drainage easements toward Marshall Creek, we check the track and the post before we blame the motor. Linear motor replacement typically runs $650 to $1,400 depending on horsepower and track condition. Slide motor repairs run $220 to $480.
Can you repair an automatic gate opener in Trophy Club the same day?
Usually, yes. We stock boards, remotes, and sensors for Viking, Ghost Controls, DoorKing, and Elite openers found in Trophy Club homes. If your control board is bad or a sensor failed, we often fix it in one trip, same day. For uncommon parts we can’t pull off the truck, we’ll give you a straight answer on timing and cost before you decide anything. Call (877) 610-2993 to check stock.
Do you warranty gate motor repairs in Trophy Club?
Every gate motor and opener job carries our 90-Day Done Right Promise in writing. If it isn’t done right, one call brings Hal back, no runaround and no haggling. That promise applies whether you’re off Trophy Club Drive, Roanoke, Lantana, or anywhere else we work. If your gate motor is failing, call us at (877) 610-2993.
Gate Access Control in Trophy Club
Gate access control in Trophy Club usually means adding a keypad, intercom, card reader, or phone-entry system to a driveway gate or community entry point, and the work typically runs $850 to $2,400 depending on how many entry points and features you need. Most Trophy Club jobs take one visit, and we schedule them inside a week. If your gate opener works but the way you get through it doesn’t, Hal or one of his crew will diagnose it and quote you upfront. Learn more about our full Gate Access Control services.
Keypad & Remote Entry
A driveway keypad that dies in a Trophy Club summer is usually not the keypad itself. The wiring run from the keypad to the opener bakes in the heat and the connection corrodes at the splice. We test the wire before we sell you a new pad, and if the pad is actually dead, we replace it with a unit rated for direct Texas sun exposure. Most keypad swaps run $180 to $400, installed. Remote programming or replacement runs $75 to $160 per vehicle.
Phone Entry Systems
Phone-entry systems work well for Trophy Club’s gated driveways because there’s no remote to lose and no code to hand out. A visitor pulls up, presses the call button, and the system dials your cell phone. You press a key to open the gate. We install and service cellular-based entry systems that don’t rely on your landline, which matters because many Trophy Club homes are cutting the copper. Installed systems start at $900 and typically run $1,200 to $2,000 with a single entry point.
Card Readers & HOA Systems
Card readers show up more on Trophy Club’s community entry gates and private lane gates than on single driveways, but some residents prefer them. The card is cheap. The reader, the controller board, and the wiring are where the money goes. We work with HOA boards on multi-card systems, and we set up credential tracking so a lost card gets deactivated without reprogramming everyone else’s. A single-reader install starts around $800, and HOA-scale systems are quoted per gate and per card count.
Will my gate access system work during a power outage?
Most gate openers have a manual release, but the keypad or phone entry unit needs power to run. We install battery backup units on request, which adds $200 to $500 to an install and keeps the access system live through short outages. For longer outages, you’ll use the manual release, and we’ll show you how that works before we leave. Call (877) 610-2993 to add backup to your system.
Do you handle HOA approval requirements in Trophy Club?
Yes. We document the existing hardware, match finishes and styles to the subdivision’s spec, and provide the paperwork most Trophy Club architectural review boards want to see before approving an access control change. We can’t promise which committee decision you’ll get, but we make the submission process straightforward. The estimate is free; call (877) 610-2993.
Gate Parts & Welding in Trophy Club
If a gate hinge has torn loose or a weld let go on a driveway gate in Trophy Club, you need someone who will fix it on the spot, not someone who wants to sell you a whole new gate. Gate welding and hinge replacement in Trophy Club typically runs between $180 and $650 depending on whether we’re repairing the existing hardware or re-setting a post that the clay soil has pushed out of plumb. Hal has been running a weld rig since 2001, and every job carries our Gate Parts & Welding 90-Day Done Right Promise.
Hinge Replacement
A gate sags because the hinge post moves or the hinge itself has worn egg-shaped. We see it all over Trophy Club’s 1990s-era subdivisions. We remove the old hinge, weld or bolt the new one in place to match the original spec, and get the gate swinging clean again. Typical hinge replacement in Trophy Club runs $180 to $380 per hinge, including on-site welding when needed.
Post Replacement
The Blackland Prairie clay under Trophy Club expands when it’s wet and shrinks when it’s dry, which twists gate posts out of plumb over time. A post that has moved far enough can’t be adjusted into submission. We dig it out, pour a deeper footing that handles the heave better, and set the post so the gate hangs true. Post replacement typically runs $400 to $950 in Trophy Club, depending on gate size and whether we need to match ornamental details.
Rail Repair & Custom Welding
Rails crack at the welds first, especially on heavier wrought-iron gates. We weld the rail back to the stile and add reinforcement where the original design was too thin. In Trophy Club, rail repair runs $150 to $400 depending on how much welding is required and whether we need to strip and repaint the affected section to match your HOA’s finish spec. Custom fabrication for obsolete or spec hardware starts around $120, quoted before any metal gets cut.
Can you match my HOA’s gate hardware specifications?
In most cases, yes. We source replacement hinges, latches, rollers, and decorative elements that match the original design documents on file with your HOA. If your subdivision requires a specific powder-coat finish or a certain latch style, we’ll confirm that before we order anything. It saves you a stalled approval. Call (877) 610-2993 and we’ll look at what you have.
What warranty comes with gate parts and welding work in Trophy Club?
Every job carries our 90-Day Done Right Promise in writing. If a weld fails or a part we installed doesn’t hold, one call brings Hal back to make it right. No prorated nonsense, no fine print, no arguing about whose fault it was. The name is on the shop, and the shop is down the road.
Brands We Service in Trophy Club
We’re certified to service nine major gate brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. We stock common control boards, gears, remotes, and safety sensors for Viking, Ghost Controls, and DoorKing locally, which means most Trophy Club repairs don’t wait on shipping. For parts we don’t have on hand, we’ll tell you straight how long it’ll take and what it’ll cost before you commit. See our brands page for full details.
Pricing for Gate Repair in Trophy Club, TX
| Service | Typical range in Trophy Club |
|---|---|
| Hinge replacement or weld repair | $190 - $340 |
| Post re-set in concrete | $280 - $520 |
| Gate realignment and sag correction | $160 - $310 |
| Opener control board replacement | $240 - $480 |
| Full gate weld-and-realign (ornamental iron) | $350 - $750 |
| Pedestrian gate installation | $600 - $1,800 |
| Single swing driveway gate with automation | $2,400 - $6,000 |
| Double swing driveway gate with automation | $4,000 - $9,500 |
| Sliding gate with motor and safety edges | $4,500 - $12,000 |
| Gate motor repair | $180 - $340 |
| New gate motor installation | $1,150 - $2,800 |
| Keypad replacement | $180 - $400 |
What pushes price up in Trophy Club: HOA finish-matching requirements, ornamental iron detail work, and post re-setting when the Blackland Prairie clay has shifted the footing. What never changes: we quote the full price in writing before any work starts, and that price is the price you pay.
Neighborhoods We Serve in Trophy Club
We work across Trophy Club, from the custom homes near the country club to the subdivisions along Trophy Club Drive and Indian Creek. Typical response time for a repair call in this area is same-day or next-morning, and emergency calls get answered live around the clock.
- Country Club Estates
- Lakeview Estates
- Whispering Glen
- The Hollows
- Arlington Forest
Service Area - Cities Near Trophy Club
We dispatch and schedule from our Dallas-Fort Worth office, and crews serve Trophy Club locally every day. If you’re just outside town, we also work in Roanoke, TX, Southlake, TX, Lantana, TX, Keller, TX, and Flower Mound, TX. Every nearby city gets the same upfront pricing and the same live-answer phone.
Serving Trophy Club, TX - Our Local Coverage Area
Gatewood Fence & Gate crews serve Trophy Club and the communities around it; dispatch is coordinated from our Dallas-Fort Worth office. The map shows the Trophy Club coverage area; if your address is on it, we can help.
Also serving nearby: Trophy Club, TX, Roanoke, TX, Southlake, TX, Lantana, TX, Keller, TX, Flower Mound, TX.
FAQs About Gate Repair in Trophy Club
Yes. We work the full 76262 area, from the streets around the Trophy Club Country Club course to the residential corridors off Trophy Club Drive and Indian Creek. If you live in any Trophy Club subdivision with HOA-governed gate standards, we already know the drill and can document your hardware for architectural review. Call (877) 610-2993 and we’ll confirm your street.
Most Trophy Club HOAs require architectural review for any visible hardware change. We photograph your existing gate, pull the original spec from your HOA’s files when possible, and match finishes and styles exactly. We provide the documentation packet; you submit it. The repair waits for approval, but the quote doesn’t change while it waits.
Yes. Every gate repair in Trophy Club carries the 90-Day Done Right Promise in writing. If something we fixed comes loose, sags, or fails again within 90 days, Hal comes back and makes it right. No fine print, no runaround. That promise is on every invoice we write for a Trophy Club address.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Trophy Club Customers Say
"He builds the gates himself in his own shop. You can go and look at it. That is not something you can say about the outfits that just order a panel in."
- Doreen Whitfield"Welded the hinge back onto our wrought iron gate on site rather than taking it away for a fortnight. Ground it back and painted it and you cannot see the repair."
- Winston Achterberg"Fitted a keypad and an intercom so my mother can let carers in without coming down the drive. He set it up and then made her practise with it until she was comfortable."
- Lucinda Marchbanks