Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Hawthorne, CA
Gate repair in Hawthorne usually means one of two jobs: a sagging wrought iron gate on a post-WWII tract home, or a high-cycle slide gate that finally quit along the aerospace corridor near Jack Northrop Ave. We fix both, and we do most of the work in your driveway with a welder running off the truck. If your gate is dragging, dead, or stuck halfway, call (877) 610-2993 and you’ll get a live person who can usually have a truck to you in 2 to 3 hours.
Why Hawthorne Homes Are Different
Hawthorne sits about four to five miles from the Pacific, close enough that the marine layer settles over the city and doesn’t burn off for months at a time. During the May-through-July June Gloom stretch, relative humidity stays high day and night, and that moisture works into every hinge pin, operator housing, and wiring connector on a gate. We regularly find rusted hinge ears and corroded limit-switch terminals in Hawthorne that would be bone dry ten miles inland.
The housing stock adds to it. Large sections of the 90250 ZIP are tract homes built between the 1950s and 1970s, and many still have original or early-replacement wrought iron driveway gates mounted to wood-frame or concrete-block perimeter walls. Wood framing moves with moisture cycles, pulling hinge screws and shifting latch alignment. Put a 60-year-old iron gate in salt-tinted air and you get a repeating repair cycle: rust at the hinges, sag at the latch, corrosion inside the operator. We know this cycle because we see it every week here.
Gate Repair in Hawthorne
Gate repair in Hawthorne tends to fall into patterns we don’t see in neighboring cities. The residential streets are full of aging iron gates fighting salt air, and the industrial blocks near Crenshaw Blvd run commercial slide gates that cycle hundreds of times a day. The job changes depending on which side of the city you’re on, and we stock parts for both. Our full Gate Repair service covers the spectrum: on-site welding, hinge and post work, operator diagnosis, and full-cycle testing before we leave.
Hinge & Post Repair
A gate sags in the hinge post, not in the middle, and in Hawthorne that post has been soaking up marine moisture for fifty or sixty years. Salt air eats hinge post welds faster than you’d see inland, especially on wrought iron that was never galvanized. A typical hinge and post repair in Hawthorne runs $280 to $750, depending on how much steel has to be cut out and whether we need to re-anchor the post footing. We weld on site, so your gate stays in the driveway while the work gets done.
Weld & Rust Repair
Rust on a Hawthorne gate is not cosmetic. Once the lower rail joints start flaking, the gate loses its structural honesty and the sag accelerates. Weld and rust repair on an iron gate usually falls between $180 and $400, and that includes cutting out the corroded section, welding in fresh steel, and treating the surrounding metal so the repair doesn’t become the next weak spot.
Electric Gate Repair
Electric gate operators in Hawthorne fail in predictable ways. The June Gloom humidity gets into the operator housing, corrodes the wiring terminals, and the gate that worked fine in September is dead by May. Electric gate operator repairs range from $225 for a simple sensor or limit switch fix to $700 and up for a circuit board replacement on a FAAC or LiftMaster unit. We diagnose the actual fault before touching anything, then quote a price you approve before work starts. Brand doesn’t matter. We carry parts for FAAC, BFT, Linear, and Viking units commonly found on Hawthorne gates.
Slide Gate Repair
Gates along Jack Northrop Ave and the aerospace corridor are a different animal. They’re high-duty-cycle slide gates, often running LiftMaster industrial or FAAC commercial operators, and they see more cycles in a week than a residential swing gate sees in a year. Slide gate rack and pinion work on the industrial corridor typically starts around $500 and climbs with duty cycle requirements. When a loop detector fails or the rack gets chewed up, the gate either won’t open for tenants or won’t close for security, so we prioritize these calls.
How much does gate repair cost in Hawthorne?
Most residential gate repairs in Hawthorne run between $180 and $750 depending on the job. A simple weld repair might sit at the low end, while a hinge post rebuild with re-anchoring lands higher. Commercial slide gate work starts around $500. Every price is quoted and agreed before work starts, and estimates are free. Call (877) 610-2993 for an exact number on your gate.
Can you come today for a gate repair in Hawthorne?
Yes, in most cases. Typical response time for Hawthorne repair calls is within 2 to 3 hours. We answer the phone with a live person around the clock, so if your gate is stuck open or won’t open at 7 a.m., you’re talking to a person who can get a truck moving, not a voicemail.
Gate Installation in Hawthorne
A new driveway or security gate in Hawthorne typically lands between $2,800 and $9,500 installed, with most residential swing gates coming in around $3,500 to $6,000. Before we quote anything, we look hard at the condition of your posts and perimeter wall, because on many Hawthorne lots, that’s where the real cost hides. Our full Gate Installation process starts with a free measure and a written price you can hold us to.
Driveway Gate Installation
A Hawthorne driveway gate on a 1950s to 1970s tract home typically runs $3,200 to $7,800 depending on width, material, and whether we’re mounting to an existing wall or pouring new posts. Many homes in the 90250 ZIP still have original wrought iron that’s spent decades in salt air, and we’ll tell you honestly whether that gate is worth saving with on-site welding or whether replacement makes better sense. We don’t sell a new gate when a repair would do, and that’s a promise we make plainly.
Pedestrian Gate Installation
Pedestrian gates in Hawthorne start around $1,800 to $4,200 installed. These are the walk gates beside the driveway and the entry gates at older apartment complexes along the major corridors. High foot traffic, salt air, and hardware that was undersized from the start means they wear out quickly if you spec cheap components. We stock heavy-duty hinges and latches that hold up.
Sliding Gate Installation
For industrial and commercial properties near the aerospace corridor, sliding gates are usually the only sensible option given the cycle counts and space constraints. These jobs in Hawthorne generally run $4,500 to $12,000 and up, because a high-duty-cycle slide gate can’t be treated like a residential swing gate. We install the full lineup, including LiftMaster industrial and FAAC commercial operators, which are the units we see most often along that stretch.
Swing Gate Installation
Swing gates are still the most common residential installation in Hawthorne, and the job typically runs $2,800 to $6,500, with double swing gates on wider driveways landing between $4,000 and $8,000. The first thing we check is the hinge post condition. Many Hawthorne homes have wood framing inside concrete-block columns, and that wood has been quietly absorbing moisture from the marine layer for fifty years. We won’t hang a new gate on a rotted post and call it done.
How fast can you get to a Hawthorne home for an installation estimate?
Most Hawthorne estimates happen within 24 to 48 hours of your call. Because the crew serves Hawthorne daily, we can often fit an estimate in the same week, sometimes the next day. Call (877) 610-2993 and you’ll reach a live person who can look at the schedule right then.
What warranty do you offer on gate installations in Hawthorne?
Every installation carries the 90-Day Done Right Promise in writing, with Hal Gatewood’s name on it. If something isn’t right within 90 days, one call brings him back. We also honor manufacturer warranties on operators and access control equipment, and we register those for you.
Gate Motor & Opener in Hawthorne
If your gate motor in Hawthorne is grinding, dead, or halfway open at the wrong time, we can usually get someone to your driveway the same day. A typical gate motor repair runs $180 to $340, and a full operator replacement with modern safety sensors lands between $850 and $1,600 depending on gate weight and post condition. Our Gate Motor & Opener service covers diagnosis, repair, and replacement across all the major brands.
Motor Repair
Most Hawthorne gate motor failures we see are not the motor itself. They’re corroded wiring terminals, worn capacitors, or a sagging gate forcing the operator to work twice as hard as it should. A service call and diagnosis inside the county carries no trip charge, and a straightforward fix like a bad capacitor or corroded terminal usually lands between $180 and $340. We diagnose the whole system, not just the symptom.
Motor Installation
When a Hawthorne operator is beyond saving, we don’t just swap boxes and leave. We check the gate’s weight, the hinge post condition, and the power supply first. Motor installation with a new residential operator, including safety photocells and labor, typically runs $850 to $1,600. Many post-WWII tract homes have gate leafs that are heavier than modern operators are rated for, so we size the motor to the gate as it actually hangs.
Slide Motor Service
Slide gate motors are a different animal, and Hawthorne has more of them than most South Bay cities. The aerospace-industrial stretch near Jack Northrop Ave runs high-duty-cycle commercial slide gates, and those operators cycle hundreds of times a day. Full slide motor replacements on commercial gates run $1,500 to $4,000 depending on duty cycle and control requirements. We stock slide gate parts and schedule commercial service around your hours.
Why does my Hawthorne gate opener fail so often compared to inland cities?
The marine layer is the main culprit. June Gloom keeps relative humidity elevated for months, and that moisture corrodes wiring terminals inside the operator housing. We apply dielectric grease to connections and use sealed connectors on splices, which slows the damage considerably. Call (877) 610-2993 for a diagnosis.
My gate sags and the motor strains. Should I replace the operator?
Usually not. The gate is sagging at the hinge post, which has settled over decades in Hawthorne’s moisture-heavy soil. Replacing the operator without fixing the post means the new motor fights the same sag and fails early. We fix the post first, then evaluate the motor.
Gate Access Control in Hawthorne
Gate access control in Hawthorne runs the gamut from a simple keypad on a residential driveway to telephone-entry and card systems at apartment complexes along Hawthorne Blvd. The common thread is the marine air, which corrodes relays, wiring connections, and keypad contacts faster than it does inland. Our Gate Access Control work starts with finding the actual point of failure, whether that’s a corroded relay or an outdated board, before we talk about spending money on replacements.
Keypad & Intercom Repair
Keypads and intercoms on Hawthorne gates take a beating from salt air and direct sun. Intercom or keypad repair in Hawthorne typically runs $140 to $350, and that covers everything from a cleaned contact or replaced relay to a full keypad swap when the housing has let moisture in. We test the full door-release sequence after the repair so you don’t get a repeat call next week.
Telephone Entry & Card Systems
Apartment and commercial properties in Hawthorne often run telephone-entry or card-reader systems tied to slide gates. The most common failure is an intercom that stops triggering the operator because a relay or wiring connection has corroded. We diagnose the relay, the power supply, and the connection to the operator before recommending a fix, and we quote the full price in writing before work starts.
How much does gate access control repair cost in Hawthorne?
Keypad and intercom repairs typically run $140 to $350. Larger telephone-entry or card-reader jobs for apartment complexes get quoted per job after diagnosis. Every quote is free, written, and fixed before any work starts. Call (877) 610-2993 to get yours.
Can you integrate a new keypad with my existing gate operator in Hawthorne?
Yes, in most cases. We match the new keypad or intercom to the operator’s control board and handle the wiring cleanly with sealed connectors so the marine air doesn’t eat the new connections the way it did the old ones. We’ll tell you up front if the existing operator can support the system you want.
Gate Parts & Welding in Hawthorne
Gate parts and welding in Hawthorne usually means one of two things: you need a specific component replaced, or you need metal repaired. We stock common parts for the operators and hardware found on Hawthorne gates, and we weld on site so the gate never leaves your property. Our Gate Parts & Welding service covers hinge ears, cracked frames, broken pickets, and custom brackets matched to your existing ironwork.
On-Site Welding
On-site welding means exactly that: the welder runs off the truck in your driveway, and the gate stays put. Weld repair on a cracked frame or post in Hawthorne typically runs $120 to $400 depending on how much steel needs to be cut out and replaced. We grind the repair smooth, prime it, and paint it to match so the fix doesn’t stand out as a scar.
Hinge Replacement
Hinge replacement in Hawthorne runs $180 to $320, and it’s one of the most common jobs we do. Salt air eats the original hinge ears on 1950s and 1960s wrought iron, and once the hinge fails the gate starts dragging and stressing the operator. We weld new heavy-duty hinges on in place and re-align the gate before we leave.
Custom Parts & Brackets
Sometimes the part you need doesn’t exist anymore, especially on gates that were custom-fabricated before the tract home was even fully built out. We fabricate custom brackets, stops, and pickets to match existing ironwork. The price varies with the fabrication work, but we quote it in writing before any cutting or welding begins.
Do you really weld on site, or does my Hawthorne gate have to go to a shop?
We weld on site. The truck carries the welder, and most hinge, post, and frame repairs happen in your driveway. The gate stays put, you can watch the work, and there’s no loading or hauling risk. Call (877) 610-2993 if you want to talk through a specific repair.
Can you match new welded steel to my old Hawthorne iron gate?
Yes. After welding in new steel, we grind the repair smooth, prime it, and paint it to match the surrounding metal. The goal is a repair that disappears visually and holds up structurally. On textured or decorative iron, we take the time to match the profile.
Brands We Service in Hawthorne
We service FAAC, BFT, Linear, and Viking alongside the other major gate operator brands. Parts for the units we see most often in Hawthorne are stocked so we’re not waiting on a truck from a distributor when your gate is down. Our brands page lists the full lineup we’re certified to service.
Pricing for Gate Repair in Hawthorne, CA
| Service | Typical range in Hawthorne |
|---|---|
| Hinge replacement (welded on site) | $180 – $320 |
| Gate sag correction / re-alignment | $150 – $300 |
| Weld repair on cracked frame or post | $120 – $400 |
| Electric operator or motor repair | $225 – $700 |
| Intercom or keypad repair | $140 – $350 |
| Hinge and post repair (full rebuild) | $280 – $750 |
| Motor replacement with safety sensors | $850 – $1,600 |
| Commercial slide gate rack and pinion | $500+ |
| Full slide motor replacement (commercial) | $1,500 – $4,000 |
| Residential driveway gate installation | $2,800 – $9,500 |
| Pedestrian gate installation | $1,800 – $4,200 |
| Commercial sliding gate installation | $4,500 – $12,000+ |
What pushes a Hawthorne job toward the higher end is usually post condition, salt corrosion on the existing steel, and duty cycle on commercial gates. Whatever the number, it’s quoted and agreed in writing before any work starts. You’ll never open an invoice bigger than the figure you approved.
Neighborhoods We Serve in Hawthorne
We run calls all over Hawthorne, from the residential streets southeast of Hawthorne Municipal Airport to the apartment corridors along Hawthorne Boulevard and the mixed industrial pockets down toward El Segundo Boulevard. Typical response time for the area is within 2 to 3 hours for repair calls.
- Ramona neighborhood (90250)
- Bodger Park and Zela Davis area (90250)
- Hawthorne Boulevard apartment corridor (90250, 90251)
- Aerospace industrial district near Jack Northrop Ave & Crenshaw Blvd (90250)
- East Hawthorne near the Inglewood boundary (90251)
Service Area - Cities Near Hawthorne
Beyond Hawthorne, CA itself, we serve the surrounding communities. If you’re in Del Aire, CA, Inglewood, CA, Lennox, CA, Lawndale, CA, or Alondra Park, CA, the same crew covers your area. There’s no trip charge inside the county.
Serving Hawthorne, CA - Our Local Coverage Area
Gatewood Fence & Gate crews serve Hawthorne and the communities around it; dispatch is coordinated from our Los Angeles office. The map shows the Hawthorne coverage area; if your address is on it, we can help.
Also serving nearby: Hawthorne, CA, Del Aire, CA, Inglewood, CA, Lennox, CA, Lawndale, CA, Alondra Park, CA.
FAQs About Gate Repair in Hawthorne
Yes. We cover every neighborhood in Hawthorne, including the 90250 and 90251 ZIP codes, from the residential streets north of Rosecrans to the industrial blocks along Jack Northrop Ave and Crenshaw Blvd. There’s no corner of the city we treat as outside our area.
Most repairs don’t require a permit. For new installations that involve pouring concrete footings or running new electrical, Hawthorne may require a permit depending on scope. We’ll tell you up front if your job needs paperwork, and we can point you to the right city office.
Typical response time for Hawthorne repair calls is within 2 to 3 hours. We answer the phone with a live person around the clock, so if your gate is stuck open at night or won’t open in the morning, you’re talking to someone who can get a truck moving right then. Call (877) 610-2993.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Hawthorne Customers Say
"Safety photo eyes on our old gate had been bypassed by whoever serviced it last, which he was genuinely annoyed about on my behalf. Fitted proper sealed ones and wired them the way they should be."
- Otis Redmond"He builds the gates himself in his own shop. You can go and look at it. That is not something you can say about the outfits that just order a panel in."
- Doreen Whitfield"Welded the hinge back onto our wrought iron gate on site rather than taking it away for a fortnight. Ground it back and painted it and you cannot see the repair."
- Winston Achterberg