Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across White House
If you live in White House and your gate is sagging, dragging, or no longer closing square, the fix usually means replacing a part or welding something that cracked. Gatewood Fence & Gate has been doing exactly that since 2001, and we do the welding right there in your driveway so the gate never leaves your property. Hal Gatewood’s name is on the shop. The phone number is (877) 610-2993, and a live person answers it around the clock. In White House specifically, we see a particular pattern: whole neighborhoods built in the 2000s have builder-spec gate openers and hinges that are now failing together, street by street. That’s the work we’re set up for.
If you’re in White House, call (877) 610-2993 and tell us what the gate is doing. We’ll tell you what it likely needs and what it’ll cost before we ever show up.
Key Takeaways
– Hinge replacement, post replacement, rail repair, and custom welding done on site in White House
– HOA approval requirements handled by us, including matching existing gate style, height, and finish
– We stock the mid-2000s LiftMaster and Ghost Controls control boards that fail by the block in White House subdivisions
– Every job carries the 90-Day Done Right Promise in writing
– Free estimates, no trip charge inside the county, $40 off any repair over $200
Why Gatewood Fence & Gate Is White House’s Preferred Gate Parts & Welding Company
Most of the gates we repair in White House were installed by the same builders who put up the houses, then left. In a 2008 subdivision off Highway 76, that means hundreds of ornamental aluminum driveway gates with the same hinges, the same powder coat, and the same opener. When the first one fails, the rest are usually a season behind. We know those gates because we’ve already fixed dozens of them. That local pattern knowledge means we bring the right parts on the first trip, not after two or three.
White House homeowners tend to call us after a national outfit told them the whole gate needs replacing. That’s the thing we push back on. A sagging gate usually means a bad hinge post, not a bad gate. A dead opener usually means a control board, not a whole new motor. Hal has been repairing what other companies want to replace since 2001, and the 90-Day Done Right Promise is stamped on every invoice, not buried in fine print.
We’re locally owned and owner-operated. That means the person who answers the phone knows the work, and the person who shows up answers to Hal. Not to a call center, not to a regional manager three states away.
Our Gate Parts & Welding Services in White House
Hinge Replacement
Hinges carry the entire weight of the gate leaf, and on ornamental aluminum gates in White House subdivisions, the original builder hinges are often undersized for the job. We replace them with heavier barrel hinges or weld-on strap hinges, powder-coated to match the existing finish. If the gate has already dropped, we lift it, true it, and set the new hinges so the gate swings level again. White House’s heavy clay soil makes this worse over time; the post moves, the hinge binds, and the leaf starts dragging on the latch side.
Post Replacement
This is the one where a little diagnosis saves real money. When a post leans, the gate sags. You could straighten the gate and call it done, but the post will keep moving and you’ll be back where you started next winter. In White House, the freeze-thaw cycle works on the clay and slowly pushes posts out of plumb. We dig out the old footing, set a new post in concrete down past the frost line where it belongs, and rehang the gate. If the HOA requires the same post style and height, we match it exactly. Fix the panel without the post and you’ll fix it twice.
Rail Repair
The bottom rail on a swing gate takes the brunt of the weather. In White House, summer humidity gets under the powder coat at weld points and starts corrosion you don’t see until the rail splits. We cut out the bad section and weld in new matching material, then coat and finish it to blend with the rest of the gate. When the HOA has approved matching hardware and finish, we reuse the original scrollwork and only replace what actually failed.
Custom Welding
Some White House properties, especially on the rural fringe of ZIP 37188, have older farm gates on pipe or wood corner posts. When ice takes a pipe post out of plumb, the weld points at the hinge barrel are often the first to split. We can weld those back on site, re-square the frame, and reset the post so the latch actually lines up again. Custom welding also covers brackets, latch plates, opener mounts, and reinforcement plates on gates that were never built for an automated opener but are getting one anyway.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in White House
The gate openers we service most in White House are the same mid-2000s units that builders installed by the street. That includes LiftMaster, Linear, and Ghost Controls residential swing and slide gate operators, plus Viking and DoorKing on commercial and community entrance gates. Because we know which boards and limit switch assemblies those units use, we stock them on the truck when we head to White House. That means one trip, not three, in the majority of cases. When a whole subdivision is running the same hardware and it’s failing the same season, knowing the brand is half the repair. The other half is having the part with you when you show up.
Common Gate Parts & Welding Problems We See in White House Homes
– Builder-spec opener failures by the block: When a 2000s-era subdivision off Highway 76 starts losing gate control boards, it’s rarely one house. The same unit was installed in every fourth driveway. We’ll fix yours, and if your neighbor’s gate starts acting up the same week, you’ll know what to tell them.
– Frost-heaved posts from heavy clay soil: White House sits on the Highland Rim, and the ground here freezes and thaws more aggressively than it does closer to Nashville. Posts that were set shallow start leaning within ten years, and once a post moves, the gate starts binding at the hinge. This is the most common repair we do in White House, full stop.
– HOA approval delays turning small fixes into big ones: If your management company takes three weeks to approve a hinge replacement, the gate keeps sagging in the meantime. The post leaches further out of plumb, the hinge barrel wears, and by the time we’re allowed to touch it, the job is a post replacement instead of a hinge swap. We submit the paperwork early and chase the approval so the damage doesn’t compound.
– Rust and split weld points on older iron gates: Bigger lots on the rural side of White House still have wrought iron or tubular steel gates that were never powder-coated properly. Summer heat and humidity get into the weld joints, and a decade later you’re looking at a split bottom rail. Those welds are repairable on site, usually same day.
Pricing for Gate Parts & Welding in White House, TN
Call (877) 610-2993 and we’ll give you the price up front. We can also give you a free second opinion on any written estimate someone else handed you. Senior and veteran discounts are permanent: 10% off, no expiration, no haggling.
We Also Serve Cities Near White House
White House sits at the top of the 37188 ZIP, but our work in the area doesn’t stop at the city line. We’re regularly in Greenbrier and Millersville for the same builder-era gate failures, down in Goodlettsville for older iron work, and over in Hendersonville for both suburban and rural gate hardware. You can learn more about our Gate Parts & Welding work across the region.
Serving White House, TN - Our Local Coverage Area
We’re based in the White House area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in White House
Does Gatewood Fence & Gate need to submit our own drawings or specs for a gate part replacement in a White House HOA?
In most cases, no. White House HOAs are the one place where approval cannot be skipped, but they rarely require homeowner-submitted engineering drawings for a like-for-like repair. We photograph the existing gate, note height, style, finish, and hardware, and submit that spec to your management company ourselves. If the HOA needs a specific paint code or finish sample, we get it. What usually delays a repair isn’t the submission; it’s waiting on a board meeting. We send the paperwork immediately so the clock starts right away.
Can you match the exact aluminum gate style my White House subdivision requires?
Yes. This is what most of our White House work actually is: a builder-spec ornamental aluminum gate from the 2000s that has to stay exactly the same height, color, and overall look. We reuse the original scrollwork, pickets, and finials where they’re still solid, and only replace the failed structural parts. When powder coating is needed, we match the finish to the existing gate rather than defaulting to whatever’s cheapest. The HOA cares about the look. We care about the structure. Both get done.
Why do multiple houses on my White House street have dead gate openers at the same time?
Because the same builder installed the same opener in every driveway when the street was platted. In White House’s 2000s and 2010s subdivisions, gate openers were part of the package, and builders bought in bulk. The control boards in those units fail on a clock, not a calendar. When one house on your street loses its board, the unit next door is usually within a season of doing the same. We stock the mid-2000s LiftMaster and Ghost Controls boards specifically because we know they fail by the block in White House. Call (877) 610-2993 and we’ll tell you if your symptoms match the pattern.
My White House HOA says my gate must stay the same height and finish, but the post is leaning. Can you fix the post without altering the approved look?
Yes, we can. We reset the post in a new footing and rehang the existing gate on it. The height, style, and finish remain the same because we don’t touch the gate leaf itself except to true it on the new post. The only visible change after the work is that the gate swings square and latches again. If the HOA wants photographs after the repair is done, we’ll provide them. In White House, we’ve done this enough that we know exactly what the management companies are looking for.
Do you coordinate with my White House property management company for a community entrance gate repair?
We handle it directly. For a community entrance gate serving a White House subdivision, we contact the management company, get the access and approval requirements, schedule the work around resident traffic, and send the invoice where it needs to go. We service the operators on community gates too, including Viking, DoorKing, and Linear units that have been in place for over a decade. You shouldn’t have to be the go-between. That’s part of the job.
When the gate won’t close, call (877) 610-2993. We answer, we show up, and the work is good or we make it right. That’s the whole arrangement.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate.