Gate Repair in Revere - Same-Day Repair, Priced Before We Start

Gate Repair in Revere, MA

Gate repair in Revere, MA usually lands between $180 and $900 depending on whether it’s a hinge, a post, a motor board, or a rusted frame. The salt air off Revere Beach eats steel faster here than almost anywhere else around Boston, so what looks like a simple sag is often corrosion that’s been working for years. Call (877) 610-2993 and a live person answers, any hour, and we’ll give you a straight written price before anyone touches a bolt.

Call (877) 610-2993

Why Revere Homes Are Different

Revere sits on an oceanfront peninsula, and that changes how we approach nearly every gate job in the 02151. Within half a mile of Revere Beach Boulevard, Atlantic salt spray settles on hinges, latches, frames, and operator enclosures twelve months a year, not just during storms. Steel that would last a decade in Malden can rust through in three seasons here. Add the winter road salt tracked onto driveways and you have a double-corrosion environment that most gate companies never plan for.

The housing stock makes it tighter. Most Revere homes went up between 1910 and 1960 as two- and three-family triple-deckers on narrow lots with side-yard driveways that barely fit a car, let alone a swinging gate arc. The posts often sit in shallow concrete poured before frost-line codes existed, and every freeze-thaw cycle heaves them a little more. So hinge placement, swing clearance, and post condition are the things we look at first, and they’re usually the real problem, not the gate panel itself.

Gate Repair in Revere

Gate repair in Revere comes down to three failure patterns we see over and over: salt-corroded hinges and latches near the coast, posts heaved out of square by freeze-thaw on pre-1960 footings, and control boards rotting from the inside out in beachfront condos. Most hinge, latch, and realignment work runs $180 to $400. Electric gate and motor repairs land in a $350 to $900 range depending on what actually failed. If your gate scrapes, binds, won’t latch, or an automatic opener moves halfway and stops, that’s a job we take same day or next morning. Our full Gate Repair service covers all of it, from a seized hinge to a full board swap.

Electric Gate Repair

Electric gate repair in Revere runs $350 to $900 depending on whether the failure is in the control board, the receiver, the safety sensors, or the operator arm itself. The salt-humid air off Massachusetts Bay corrodes circuit boards and wiring terminals far faster than inland installs, so we check for corrosion at the connection points even when the symptom looks purely electronic. We service Viking, Ghost Controls, and DoorKing operators regularly, and we can usually pull parts the same day from our Boston-area stock.

Automatic Gate Repair

Automatic gate systems along Revere Beach Boulevard and in the newer condo developments near Wonderland station fail in a way inland contractors almost never see: interior corrosion from salt-laden air that seeps past weather seals and settles on control boards over several seasons. We open the enclosure, clean and reseal the connections, replace only what has actually failed, and reset the travel limits so the gate stops binding. The diagnosis with a written repair plan is free.

Hinge & Post Repair

Hinge and post repair in Revere starts around $225 and climbs based on how much of the post base has rotted or cracked. The freeze-thaw cycle heaves posts set in shallow footings, which is exactly what happens when a post was poured in 1962 and never redone. We dig, reset, regrout, and realign, and Hal welds on site so the work stays in your driveway where you can watch it. A cracked post fixed without addressing the footing means fixing it again in two winters.

Gate Realignment

Gate realignment in Revere runs $180 to $340 for most residential swing gates on standard lots. On the narrow side-yard driveways common to Revere’s two- and three-family homes, a sagging gate scrapes concrete or brick within weeks of going out of alignment. We adjust the hinges, shim the post if it’s still sound, and reset the latch so the gate closes clean on the first try. If the post itself is cracked, we tell you before we start, because fixing the panel without the post means fixing it twice.

How fast can you get to a gate repair in Revere?

In most cases we can have someone at your Revere property within two hours of your call, and same-day service is common for hinge, latch, and realignment work. Scheduling is coordinated from our Boston office, and crews serve Revere locally all week, including evenings and weekends. Call (877) 610-2993 and you’ll get a live person who can tell you exactly when the truck arrives.

How much does gate repair cost in Revere compared to other cities near Boston?

Gate repair in Revere runs about the same as Chelsea, Everett, and Winthrop, typically $180 to $900 depending on the work. But Revere’s coastal salt exposure often means swapping in stainless or galvanized hardware, which can add $40 to $120 to a hinge or latch repair. That’s not a markup. It’s the only way to keep the repair from rusting out again in two seasons.

Gate Installation in Revere

Gate installation in Revere, MA costs between $1,800 and $15,000 for most residential projects. A basic swing gate on a triple-decker driveway runs $1,800 to $4,500. An automatic sliding gate for a condo complex near Revere Beach Boulevard typically lands between $5,500 and $12,000. You’ll get a written price before the first hole is dug, and every installation carries the 90-Day Done Right Promise. Our Gate Installation work starts with a free on-site measure, because Revere driveways almost never match the standard specs.

Sliding Gate Installation

Sliding gates are the workhorse on Revere’s triple-decker and shared-driveway lots. When a swing gate would arc into a neighbor’s car or block the narrow side-yard access, a slide gate tucks along the fence line and uses almost no clearance. On a three-decker off Shirley Avenue, we installed a slide gate for a shared driveway where a swing gate would have blocked the neighbor’s parking. The old post footing had heaved from freeze-thaw, so we poured a new 42-inch-deep footing and mounted the operator in a sealed enclosure built for salt air.

Driveway Gate Installation

Most Revere driveway gates go on narrow openings between a house and a fence line, so the hinge side matters more than the gate panel itself. We set swing gates on heavy steel posts in concrete footings dug below frost line, because Revere’s freeze-thaw cycle will heave anything shallower within two winters. A single driveway swing gate here runs $1,800 to $4,500. A double gate system for a wider opening runs $4,000 to $9,000, depending on automation and hardware.

Pedestrian Gate Installation

Pedestrian gates on Revere lots are often the daily entry for tenants in two- and three-family homes, opened hundreds of times a day, and they fail at the hinge or the latch, not the panel. We hang them on stainless or galvanized hinges rated for coastal exposure and set the latch so it catches clean without slamming. A standard pedestrian gate with hardware in Revere runs $900 to $2,200.

Do Revere beach-area gates need different hardware than inland ones?

Yes. Within about a half-mile of Revere Beach Boulevard, the combination of ocean salt spray and winter road salt creates a double-corrosion environment. Stainless hinges, galvanized frames, and sealed operator enclosures are practical necessities here, not upgrades. A standard steel gate installed a few blocks inland can run a decade without serious corrosion; the same gate facing the Atlantic in Revere can rust through in three seasons.

Can you install a sliding gate on a narrow Revere triple-decker driveway?

Yes, and it’s often the only option that actually works. Sliding gates ride along the fence line instead of arcing into the side yard, so they clear parked cars and tight access paths that would block a swing gate. We’ve done this on Shirley Avenue, Broadway, and Winthrop Avenue. The key is a deep, properly poured footing, because the slide track binds if the ground shifts even a little.

Gate Motor & Opener in Revere

Gate motor repair in Revere runs $240 to $600 for most jobs, and we get to Beachmont, Shirley Avenue, and West Revere the same day you call. When a Revere homeowner calls (877) 610-2993, a live person answers. Not a recording, not a queue. Somebody who knows what a 02151 driveway looks like and why the opener died. We fix swing and slide operators on all the common brands, and our Gate Motor & Opener work includes an honest assessment of the post and hinges before we mount anything new.

Motor Repair

Most Revere motor repairs are board-level, control panel, limit switch, or capacitor failures, not entirely dead units. We find the actual fault instead of pushing a replacement box. A capacitor replacement runs $120 to $220. Control board replacement runs $300 to $700 on most brands, though sealed-board coastal models sometimes run slightly higher because the enclosure itself needs rebuilding. Our on-site welding means we can also repair a steel operator bracket or post plate rather than waiting two weeks for a weld-on replacement.

Slide Motor

Revere Beach condos and access-controlled developments along Revere Beach Boulevard use slide gate motors heavily, and these units fail in ways inland slide motors don’t. Salt-humid air gets into the enclosure and the board corrodes from the inside. A slide motor drive gear replacement starts around $400. Full slide operator replacement on a typical 14-foot condominium gate runs $2,200 to $5,800, including the rack and pinion check and safety photocell recalibration. We always inspect the existing rack for wear before mounting a new operator, because a new motor on a chewed-up rack eats the pinion in months.

Linear Motor

Linear gate motors show up on older Revere swing gates and small commercial enclosures. They’re simple machines, and when they die it’s usually the thrust bearing or the internal limit switches. We rebuild what’s rebuildable. A Linear swing arm motor rebuild runs $250 to $480; a full operator replacement runs $1,200 to $2,800 installed. Because Linear parts are easy to get, we usually complete the repair in one visit instead of scheduling a return trip.

Is it legal to keep using my old swing gate opener without photo-eyes in Revere?

It may still be legal depending on when it was installed, but it’s not safe, especially on a Revere lot with a public sidewalk directly against the gate’s sweep radius. Adding photo-eyes to an old operator requires a compatible control board and rewiring, and some legacy operators can’t be retrofitted at all. We’ll tell you which you have and what the retrofit costs if it’s possible.

Do I need a different gate motor for a driveway within a half-mile of Revere Beach?

In practical terms, yes. A standard sheet-metal enclosure with a vented lid will kill a control board in two to three years in the Revere Beach corridor. We specify sealed NEMA 4X enclosures, stainless or galvanized hardware, and dielectric isolation on every job within a half-mile of Revere Beach Boulevard. The motors are the same models used inland; it’s the sealing and hardware that change.

Gate Access Control in Revere

Gate access control in Revere means dealing with two things most Boston-area gate companies never think about: salt air that eats control boards from the inside, and driveways so tight you can barely fit a wheelbarrow beside the gate. A keypad or card reader that works fine in Malden can be dead in two seasons on Revere Beach Boulevard. We install and repair keypads, card readers, phone entry, video intercoms, and smart access systems, and our Gate Access Control work always considers how close you are to the water.

Keypad Entry

Keypad entry is the most common access system on Revere driveways, and the one that fails most often near the water. Salt-humid air gets into the keypad body, corrodes the ribbon cable and the board, and buttons start working intermittently. We replace the board, rebuild the keypad with sealed gaskets, and test continuity through the wiring run back to the operator. In the Beachmont and Crescent Beach sections, we only install keypads rated for wet coastal use, not the cheap plastic housings that last two winters.

Card Reader

Card readers on Revere Beach condo slide gates take a beating from salt spray year round. The internal contacts tarnish until the reader only works half the time. We replace the reader, wire it through a sealed enclosure, and set the controller to fail open if the reader loses power so no one gets locked out of the garage. A typical card reader swap in Revere runs $450 to $900 installed.

Video Intercom

Video intercom is the upgrade Revere homeowners ask about most, especially in oceanfront buildings where residents want to see who is at the gate before opening anything. We install wired and Wi-Fi video intercoms on existing swing and slide gates, including the newer condo buildings along Revere Beach Boulevard. Within a half-mile of the water, the video module mounts in a sealed, heated enclosure, because a camera that works in July in Medford fogs and shorts by November on the beachfront.

Why does my Revere Beach condo slide gate keypad work intermittently, even after a new board?

Because the new board was almost certainly installed in the same unsealed enclosure that killed the old one. Within a half-mile of Revere Beach, salt-humid air penetrates standard electrical boxes, corrodes ribbon contacts and ground traces, and the keypad drops out randomly. The fix is sealing the enclosure properly and, on some oceanfront slide gates, replacing the keypad housing with a marine-rated unit.

Can you add a video intercom to an existing Revere swing gate without replacing the whole operator?

Yes, as long as the operator is in good working order and the gate post structure is sound. We add video intercom systems to existing swing and slide gates across Revere all the time. The video module mounts on a sealed gooseneck or in a flush box near the gate and ties into the operator’s accessory trigger input.

Gate Parts & Welding in Revere

Gate hinge replacement in Revere runs $220 to $480 per hinge pair, and post replacement usually falls between $650 and $1,400 depending on footing depth and concrete work. Most parts and welding repairs on this side of the city get done same day or next morning. If your gate is sagging, scraping the driveway, or the post is heaving out of the ground from another hard freeze, call (877) 610-2993 and we’ll give you a straight price before any work begins. That’s the core of our Gate Parts & Welding service: fix what’s actually broken, in the driveway, without hauling the gate off to some shop.

Hinge Replacement

Most sagging gates in Revere sag because the hinge post has moved or the hinge leaves themselves have corroded. Near the water, plain steel hinges rust through in a few seasons. We replace them with stainless or galvanized pairs, weld the new leaves onto the frame, and re-align the swing arc so the gate clears the driveway without scraping. A hinge replacement on a standard swing gate runs $220 to $480 per pair, including welding and adjustment.

Post Replacement

Revere’s freeze-thaw cycle is brutal on gate posts set in shallow footings. Older homes built between 1910 and 1960 often have posts sunk only two to three feet into the ground. When the ground heaves, the post moves, the gate binds, and the weld cracks at the base. We dig out the old footing, pour a deeper concrete pier that goes below frost line, and set a new galvanized post. Post replacement in Revere generally runs $650 to $1,400, depending on post size and how much concrete work is involved.

Custom Welding

When a gate section is too far gone for a patch or you need a bracket fabricated, we do custom welding right on site. That includes building custom hinge brackets, reinforcing corroded frame corners, and repairing damaged drop rods or latch mounts. Revere’s salt air means we default to stainless or galvanized stock for anything that will live near Revere Beach Boulevard. Custom welding jobs start around $150 for smaller brackets and run to $900 to $1,800 for full gate frame reconstruction, depending on scope.

Why did my gate hinge post crack at the base in Revere even though the gate itself looks fine?

The post cracked because a shallow footing heaved during a freeze-thaw cycle. Revere winters cycle above and below freezing dozens of times, and posts set only two to three feet deep move every time the ground expands. The gate looks fine because the frame is doing its job; it’s the post that’s taking the stress and cracking at the weld line.

What’s different about welding a gate frame on Revere Beach versus inland suburbs like Malden?

The difference is salt, and lots of it. Within a half-mile of Revere Beach Boulevard, the air carries Atlantic salt spray year round, not just in winter. Add winter road salt, and steel components in Revere corrode at double the rate they would in Malden or Medford. That’s why we weld with stainless or galvanized filler rod and use sealing primer on anything ferrous.

Brands We Service in Revere

We service and repair Viking, Ghost Controls, DoorKing, and Elite operators in Revere, along with LiftMaster, FAAC, BFT, Linear, and Mighty Mule. Common boards, capacitors, and limit switches for these brands are kept in local stock, so most repairs don’t wait on a parts shipment. See our brands for the full list.

Pricing for Gate Repair in Revere, MA

Neighborhoods We Serve in Revere

We work throughout the 02151, from the beachfront stretch to the side streets off Broadway and Revere Beach Parkway. You’ll typically see us the same day you call, or next morning at the latest.

• Beachmont
• West Revere
• Revere Beach Boulevard area
• Shirley Avenue corridor
• Point of Pines

Service Area - Cities Near Revere

We also repair and install gates in the towns right around Revere. If you’re in Chelsea, MA, Everett, MA, Winthrop, MA, Malden, MA, or Saugus, MA, we’ll come to you. And our Revere, MA page covers the city in more detail if you need it.

FAQs About Gate Repair in Revere