Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across New Rochelle
Gate hinge replacement in New Rochelle typically runs $240-$480 per hinge assembly, and post replacement usually lands between $650 and $1,400 depending on whether we’re dealing with a rotted footing or just a leaning post. Most repair work on this side of Westchester gets done same-day or next-day because we keep stainless and galvanized stock on the trucks. If your gate is dragging, sagging, or the post is leaning toward the sidewalk, call (877) 610-2993 and Hal will talk you through what you’re seeing before anyone even rolls out.
The thing about New Rochelle gates is that they don’t fail the way gates fail in, say, White Plains or Scarsdale. The Sound is right there. Salt air works on hinges, latches, and weld points every single day, whether you notice it or not. We’ve been pulling up to homes from Wykagyl down to Five Islands Park long enough to know which blocks eat hardware the fastest. When someone in the 10801 zip calls about a gate that won’t swing, we already know what we’re probably going to find before we open the truck door.
Why Gatewood Fence & Gate Is New Rochelle’s Preferred Gate Parts & Welding Company
Hal Gatewood started this shop in 2001, and his name has been on every invoice since. That matters in a city like New Rochelle, where a lot of the work we do is on older properties that have been through three or four contractors over the years. Homeowners in the North End and Wykagyl don’t want a rotating cast of strangers at the gate. They want the same person who fixed the hinge last spring to be the one who answers when the operator board quits in December. That’s the arrangement here.
Every call to (877) 610-2993 gets answered by a live person, 24 hours a day. Not a voicemail tree, not a dispatch queue somewhere in another state. If a gate won’t close and your dog is standing at the front door at 7 a.m., you get a human voice. And that human can usually get a crew to most New Rochelle addresses within the hour, because we stage trucks in the area. Hal’s crews have been through every zip code in New Rochelle, including 10801, 10802, 10804, and 10805 enough times to know the streets without a map.
We publish our address. We publish our license number. If you want to drive to the shop and look Hal in the eye before you hire us, the door is open. That’s the kind of accountability that national companies can’t fake, and it’s the reason so much of our work in New Rochelle comes from referrals. People tell their neighbors because they know the name on the truck is the same name on the shop.
Our Gate Parts & Welding Services in New Rochelle
Hinge Replacement
Hinges are the first casualty of Long Island Sound salt air. The pins seize, the brackets corrode, and the whole panel starts hanging its weight on the post instead of the hinge. In New Rochelle’s coastal zones around Glen Island and the 10805 zip, we routinely replace hinges that are only three to five years old with sealed-bearing stainless units that actually survive. A hinge replacement on a standard swing gate here runs $240-$480 per hinge assembly, including the bracket work. For ornamental iron gates on Wykagyl estates, we match the barrel size and finish so the new hardware doesn’t look like a hardware-store afterthought bolted onto a 90-year-old gate.
Post Replacement
When a hinge post snaps at the footing, the gate doesn’t just sag. It drops. And in New Rochelle, post failure isn’t rare. The freeze-thaw cycle heaves masonry posts on older North End properties, while salt corrosion eats steel posts from the inside out within a half-mile of the Sound. We cut out the rotted section, weld in a galvanized stub with a stainless hinge bracket, and reset the post in new concrete. A full post replacement in New Rochelle typically runs $650-$1,400 depending on footing condition and whether we’re matching stone, brick, or steel. The gate stays in your driveway the whole time. We don’t haul it off to some shop across the county.
Rail Repair
Original wrought-iron rails from the 1920s and 1930s rust through from the inside. You’ll see a hairline crack in the paint one summer, and by fall the rail is split clean through. Rail repair on New Rochelle’s older ornamental gates usually means cutting out the rotted section, welding in matching solid bar stock, and grinding the joint smooth so it disappears under the finish. We do this on site, at your gate, with the panel still hung. Typical rail repair runs $180-$400 per section depending on length and access. If the scrollwork is intact, we leave it alone. No point cutting apart good iron to fix the bad.
Custom Welding
Sometimes a gate doesn’t need a repair. It needs a modification. Maybe you’re widening a driveway entrance off North Avenue, or adding a matching section to close a gap the previous owner never got around to. Or maybe the gate needs a new latch mount because the original was drilled by a handyman with no sense of geometry. Hal’s crew does custom welding on site for gates all over New Rochelle, from simple bracket fabrication to full ornamental ironwork repair. Custom welding work in New Rochelle generally runs $150-$600 per hour of shop-and-site time depending on the complexity and how much of the original iron we’re working around. The price is quoted before we strike an arc.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in New Rochelle
We service and stock parts for the operators you already have, including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That matters in New Rochelle because a gate near the water doesn’t have time to wait while somebody orders a board from a warehouse in Ohio. We keep common Linear, Viking, and DoorKing parts on the trucks that serve this area, so when your operator quits and the gate is stuck open, the fix often happens the same day we see it. Not every gate company in Westchester carries stock like that. We do because we know how fast coastal air kills electronics and hardware. Gate Parts & Welding is what we do every day, and we built the parts inventory to match the calls we actually get.
Common Gate Parts & Welding Problems We See in New Rochelle Homes
- Hinge seizure on coastal swing gates. Salt crust builds up inside the hinge barrel and locks the pin in place. The gate still moves, but the load transfers to the post, and that’s when the post starts to lean and eventually snap. Within a half-mile of the Sound, this shows up years earlier than inland.
- Weld point failure on original ornamental iron. Gates from the 1920s through the 1950s were forge-welded, and those joints are the first to rot through from internal corrosion. You’ll see rust weeping out of the joint before you see the crack. By the time the crack is visible, the section usually needs to be fully cut out and re-welded.
- Galvanized hardware failing after installation scratches. We see this constantly in the 10801 and 10805 zip codes. A galvanized hinge or bracket worked fine in the box, but whoever installed it scratched the zinc coating, and bare steel met salt air. Three to five years later, it’s rusted through. Stainless hardware avoids that entirely.
- Frost heave throwing alignment out of spec. Older stone and brick pillars in the North End absorb winter moisture and shift during freeze-thaw cycles. The gate that swung perfectly in August scrapes the brick apron in March. Usually it’s not the gate that moved. It’s the post.
Pricing for Gate Parts & Welding in New Rochelle, NY
Here’s what you can expect to pay in New Rochelle for the most common repairs, quoted before any work starts and agreed in writing:
- Hinge replacement: $240-$480 per hinge assembly, including sealed-bearing hardware
- Post replacement: $650-$1,400 depending on footing work and post material
- Rail repair: $180-$400 per section
- Custom welding: $150-$600 per hour of shop and site time
- Latch and lock replacement: $120-$320 for most gate hardware
- Gate roller replacement: $90-$230 per roller assembly on sliding gates
These are real numbers for New Rochelle’s market, not national averages. Coastal properties pay a little more for stainless and sealed-bearing hardware because that’s what actually lasts. Inland 10804 homes can often use standard galvanized components. Either way, the price is the price before the work starts. Every estimate is free, and if you have a written quote from another company, bring it in and Hal will give you a second opinion at no charge. Call (877) 610-2993.
We Also Serve Cities Near New Rochelle
Most of our New Rochelle work is centered in the 10801, 10802, 10804, and 10805 zip codes, but the trucks run through Pelham, Pelham Manor, Larchmont, and Wykagyl all the time. If your gate is giving you trouble and you’re just outside the New Rochelle line, call anyway. Gate Parts & Welding in New Rochelle doesn’t stop at the city sign, and neither do we.
Serving New Rochelle, NY - Our Local Coverage Area
We’re based in the New Rochelle area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in New Rochelle
Scarsdale sits well inland. New Rochelle is on Long Island Sound, and the salt-laden coastal air around neighborhoods like Glen Island and Five Islands Park corrodes bare steel and scratched galvanized hardware at a dramatically accelerated rate. A hinge that lasts 15 years in Scarsdale can seize or rust through in five here. The fix is sealed-bearing stainless hardware and an annual rinse of the gate with fresh water to knock the salt crust off. Call (877) 610-2993 and we’ll quote the right hardware for your exact block.
Yes, and that’s most of what we do on New Rochelle’s older estate properties in Wykagyl and the North End. We match the original bar stock and scrollwork as closely as possible, weld the replacement section in place, and grind the joint flush so the repair disappears under primer and paint. On a Wykagyl estate with an original 1930s ornamental swing gate, we found the lower hinge post corroded through at the footing. The panel had sagged until it dragged on the brick apron. Our crew cut out the rotted section, welded in a new galvanized post stub with a stainless hinge bracket, and rehung the gate with new sealed-bearing hinges from LiftMaster’s accessory line. Alignment restored without touching the historic scrollwork. That’s the standard, not a special favor.
Sealed-bearing stainless hinges, period. Within a half-mile of the Sound, standard zinc-plated hinges will begin to seize within three to five years because the salt crust works into the barrel and locks the pin. Stainless brackets and sealed-bearing barrels cost more upfront, usually $300-$480 per hinge assembly installed, but you won’t be re-welding the post every few seasons. Given what post failure costs in New Rochelle, the upgrade pays for itself the first time you don’t need it. Call (877) 610-2993 for a quote on your specific gate weight and post condition.
Could be either, but near the Sound it’s usually corrosion in the low-voltage wiring or the limit switch contacts first. Salt air works on copper just like it works on steel. The operator board itself can also fail from condensation cycles inside the housing, especially if the box isn’t properly sealed. We diagnose this in New Rochelle regularly, and the local pattern we see is that operators within a half-mile of the water need their connections cleaned and dielectric-greased every year, not every three. If your gate quits every spring, you have a corrosion problem, not a mystery. We’ll find it and fix it right. Call (877) 610-2993.
If you’re in the 10801 or 10805 zip code, yes. The corrosion line in New Rochelle runs roughly a half-mile inland from the shoreline, and even one or two blocks off the water means elevated year-round salt exposure that standard hardware can’t survive. Inland 10804 properties can usually get away with galvanized components, but coastal blocks need stainless hinges, stainless brackets, and sealed-bearing rollers. The cost difference is real, usually $100-$200 more per hinge, but it’s the difference between replacing hardware every five years and not thinking about it for fifteen. Call (877) 610-2993 and we’ll match the spec to your exact location, not the city average.
Call Gatewood Fence & Gate for Gate Parts & Welding in New Rochelle
If your gate is sagging, seized, rusted through, or just not latching, call (877) 610-2993. You’ll talk to a person, not a machine. Hal will ask you what the gate is doing, what side of New Rochelle you’re on, and whether it’s ornamental iron or modern steel. Then he will give you an honest read, a free estimate, and a time window he actually keeps. The name is on the shop, and the shop is down the road. That’s the oldest accountability there is.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving New Rochelle since 2001.