Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Johns Creek
Gate Installation in Johns Creek usually means one of two things: a hinge post that has leaned out of plumb and let the gate drag, or a control board that took a lightning hit during a summer thunderstorm. Around here it is usually both eventually. We run a full welding rig and a stocked parts van through Johns Creek every week, and Hal Gatewood has been fixing gates like these since 2001. If your gate is sagging, binding, or dead at the keypad, call (877) 610-2993 and you will get a live person, not a recording.
Why Gatewood Fence & Gate Is Johns Creek’s Preferred Gate Parts & Welding Company
Johns Creek is a particular kind of place when it comes to gates. The planned communities along State Bridge Road, Parsons Road, and McGinnis Ferry Road went up fast in the 1990s and early 2000s, and most of them put in automated entrance gates at the same time. Those gates are now 20 to 30 years old, which means their original hinges, posts, and control boards are reaching the end of their service life at roughly the same moment. We have spent years working inside those communities, and we know what fails first on the FAAC, Elite, and LiftMaster operators that were the standard spec for that era of Atlanta-area build-out.
What really matters to a Johns Creek HOA board is whether the company they call knows the difference between a gate that can be welded back true and a gate that needs to be replaced. We fix the gate in place whenever it makes sense. We do not haul it off and sell you a new panel because it is easier for us. Our Gate Parts & Welding crew carries the hinges, rollers, posts, and control boards that fit the exact systems installed across this part of Fulton County, and every job carries the 90-Day Done Right Promise in writing. Hal’s name is on the shop and on every invoice, and that has not changed in over two decades.
Our Gate Parts & Welding Services in Johns Creek
Here is what we actually do in Johns Creek, week in and week out. You will notice we lean hard into the structural fixes, because around here, that is what fails first.
Hinge Replacement
A gate sags in the hinge post, not in the middle, and that is where we start. On older Johns Creek swing gates, the original hinges were often undersized for the weight of a steel or aluminum panel hung on a brick column. We cut off the old hinge, weld on a heavier plate, and set the gate back to its original swing line. In the 30022 zip code we commonly see hinge barrels that have worn egg-shaped from years of red clay heave shifting the post. We stock replacement hinge assemblies and weld them on site so the gate never leaves your driveway.
Post Replacement
Georgia’s red clay is the quiet enemy of every gate post in Johns Creek. The soil swells when wet and shrinks when dry, and over 20 years that cycle pushes a post out of plumb by inches. A gate that scrapes the ground near the hinge post almost always has a post problem, not a panel problem. We dig out the old footing, pour a new concrete collar, and set the post true. If the post is still sound, we can weld a reinforced base plate and save the structure. If it is rusted through below grade, we replace it and match the existing brick or stone as closely as the original build allows.
Rail Repair
Slide gates on ground tracks are common throughout Johns Creek’s older planned communities, and their failure mode is predictable: the clay shifts, the track heaves, the gate racks, and the rollers shear. We straighten and reinforce bent rails, replace the rack and pinion gear teeth, and reset the track on a compacted base so the gate rolls without binding. The fix is usually weld-on and same-day, and it costs a fraction of what a full gate replacement would run. The key is doing it before the gears get chewed to the point where the operator motor burns out dragging a bound gate.
Custom Welding
Sometimes the right fix is not a part from a catalog. We weld custom hinge plates, reinforced corner brackets, latch mounts, and panel patches on site. If a gate leaf is cracked at a stress point, we grind it clean, weld it solid, and often add a gusset so it does not crack again. For HOA entrance gates in Johns Creek, that kind of repair keeps the gate in service while the board decides whether a full replacement is in the budget this year or next. We would rather weld it right and buy you five more years than sell you a gate you do not need yet.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Johns Creek
We are certified to service nine major gate brands, and around Johns Creek the ones we see most are FAAC, Elite, and LiftMaster on community entrances, with Viking, Ghost Controls, DoorKing, and Mighty Mule on private driveway gates. For Johns Creek Gate Motor & Opener issues, we stock parts for the operators that dominate the area. The synchronized build-out of Johns Creek means we know which control boards were specified in which subdivisions, and we stock parts for the operators that dominate the McGinnis Ferry, Parsons, and State Bridge corridors. That means fewer return trips and a gate that is back in service on the first visit.
Common Gate Parts & Welding Problems We See in Johns Creek Homes
- Clay heave pushing hinge posts out of plumb. The wet and dry cycles in Johns Creek’s red clay soil move a post by fractions of an inch each season. After 20 years, the gate drags on its latch post and the hinge welds start to crack.
- Lightning strikes killing control boards. Summer thunderstorms in this part of Fulton County are intense and frequent. Voltage spikes run through low-voltage keypads and boards, and older systems built before modern surge protection are especially vulnerable.
- Ground-track slide gates racking and binding. The clay shifts under the track, the gate no longer rolls true, and the rack and pinion gear teeth shear under the load. Left alone, it burns out the operator motor too.
- Legacy safety photocells burned out or misaligned. On 1990s and early 2000s systems, the photocells are often original, and many are no longer compliant with current UL 325 safety standards. We replace them when we are on site, not as a separate upsell.
Pricing for Gate Parts & Welding in Johns Creek, GA
You should know what to expect before you call. A typical hinge replacement on a Johns Creek swing gate runs $180 to $450 depending on the gate’s weight and whether the post needs resetting. Post replacement with a new concrete collar typically runs $600 to $1,400 when excavation and brick matching are included. Rail repair on a slide gate usually falls between $300 and $800. Custom welding work is quoted by the job, but most on-site welding repairs land between $150 and $600. Every price is quoted and agreed before any work starts, so there is no number you did not approve waiting for you at the end. We waive the trip charge inside the county, take $40 off any repair over $200, and offer permanent 10% discounts for seniors and veterans. Call (877) 610-2993 and we will give you a written number before we touch a tool.
We Also Serve Cities Near Johns Creek
Gatewood Fence & Gate runs the same stocked parts van and welding rig through the communities just beyond Johns Creek: Alpharetta, Peachtree Corners, Roswell, and Milton. If your HOA gate is on the border of two service areas, call us anyway. The Gate Parts & Welding in Johns Creek shop is close, and we will tell you honestly how soon we can be there.
Serving Johns Creek, GA - Our Local Coverage Area
We’re based in the Johns Creek area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Johns Creek
In most cases that gate can be welded and the post reset, and the repair will cost far less than a full replacement. The sag is nearly always a post that has leaned out of plumb from red clay heave, not a failed panel. We cut out the old footing, pour a new concrete collar, and weld a reinforced hinge plate back onto the original leaf. At a 30022 community off Parsons Road, our techs found a 2003-era FAAC swing gate leaning hard on its hinge post after years of red clay heave. We cut out the rusted post footing, poured a new 36-inch concrete collar, and welded a reinforced hinge plate back onto the original gate leaf, saving the HOA a full panel replacement. The board’s safety photocell had also burned out during the last thunderstorm, and we replaced it before the gate went back into service. If your panel is rusted through at the hinge line, replacement becomes the honest answer, but we will show you before we recommend it. Call (877) 610-2993 for a free on-site look.
Usually yes, and the root cause is the clay under the track. Johns Creek’s red clay expands when wet and shrinks when dry, which heaves the track slightly out of level and forces the rack and pinion gears to mesh incorrectly. The gears shear, the gate binds, and if it runs long enough like that, the operator motor burns out. We reset the track on a compacted base, replace the worn gear teeth, and weld any bent rail sections. Call (877) 610-2993 and we will diagnose it before we quote it.
We stock parts for the operators that dominate Johns Creek’s 1990s-to-2000s build-out: FAAC, Elite, and LiftMaster most heavily, plus Viking, Doorking, and Ghost Controls boards on the van. For older boards that are no longer manufactured, we can often repair the board or source a rebuilt unit, and we will tell you plainly when retrofitting a modern board with surge protection is the smarter long-term move. Estimates are free, so call (877) 610-2993 and we will tell you what you are dealing with.
Many 1990s and early 2000s gates in Johns Creek were built with photocells that no longer meet current UL 325 safety standards, and some were never retrofitted when the standards tightened. Proper Gate Access Control in Johns Creek requires modern safety devices that fail visibly, not silently. The practical issue is that an obsolete photocell often fails quietly, leaving the gate to close on a vehicle or a child. We inspect those cells on every job and replace non-compliant or burned-out units as part of the repair, not as a separate upsell. If you are not sure what is on your gate, call (877) 610-2993 and we will check it.
Every six months for lubrication, and replacement depends on wear. On a Johns Creek community gate that cycles hundreds of times a day, hinge barrels can wear egg-shaped within five years if they were undersized from the start. A gate that is properly lubricated and adjusted will run quietly; one that creaks or drops when it opens is telling you the hinge is worn. We weld on heavier hinge assemblies that hold up longer, and the work is covered by our 90-Day Done Right Promise. Call (877) 610-2993 to schedule a look.
Contact Gatewood Fence & Gate in Johns Creek
If you have a gate that sags, binds, or will not open after a storm, call (877) 610-2993. Hal Gatewood answers with a live voice around the clock, and he will quote the work before any of it begins. Serving Johns Creek, GA and the surrounding communities with on-site welding, honest repair-first recommendations, and a 90-Day Done Right Promise in writing on every job.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Johns Creek and surrounding communities since 2001.