Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Johns Creek
Gate installation in Johns Creek runs between $4,800 and $18,500 for most homes here, depending on whether you’re doing a single pedestrian gate or a heavy custom double swing gate with automation. We measure on site, quote the full job in writing before any work starts, and then build it so it stays square through Georgia’s wet-dry clay cycles. Call (877) 610-2993 for a free estimate.
We know Johns Creek differently than a company that just typed your ZIP code into a GPS. We know the neighborhoods along State Bridge Road where original 1990s gate operators are failing in clusters. We know what red clay does to a hinge post over twenty seasons. And when Hal Gatewood’s crew shows up in Johns Creek, we’re bringing parts for the brands actually installed here: FAAC, LiftMaster, Linear, and Ghost Controls.
Key Takeaways
- Custom gate installation in Johns Creek typically runs $4,800-$18,500 depending on size, automation, and site prep
- Most Johns Creek homes sit on expansive red clay that shifts hinge posts out of plumb, so proper footings matter more than the gate itself
- Hal Gatewood’s name is on the shop and on every invoice since 2001; every job carries a written 90-Day Done Right Promise
- We weld on site, quote before we start, and a live person answers the phone 24/7 at (877) 610-2993
Why Gatewood Fence & Gate Is Johns Creek’s Preferred Gate Installation Company
Gate installation in Johns Creek is not a one-size-fits-all trade. The first thing we do is look at the ground. Johns Creek’s red clay expands when wet and contracts when dry, and that movement is exactly why so many ornamental gates in this city start binding at the latch within five years. A gate sags in the hinge post, not in the middle, and that is where we start.
We’re the company HOA boards call when a 30-year-old entrance gate finally gives out on McGinnis Ferry Road and 300 homeowners need it back online before morning rush hour. That work takes a different approach than a single driveway gate off Bell Road. It takes planning around school drop-off times, understanding emergency vehicle access, and sometimes staging a temporary gate so nobody loses access for three days. We’ve done enough of these replacements in Johns Creek to know the sequence cold.
And you won’t reach a call center. Hal Gatewood answers the phone at the shop, or someone in the shop answers. You’ll get the name of the person who shows up. We’re background-checked, uniformed, and we carry parts for nine major gate brands on the truck. When a Johns Creek customer calls because a summer storm fried their gate board, we don’t tell them to wait a week for a part. We likely have it.
Every job carries Hal Gatewood’s 90-Day Done Right Promise in writing. If it’s not done right, we make it right. One call brings him back. That’s the promise, plain and not buried in fine print.
Our Gate Installation Services in Johns Creek
Driveway Gate Installation
A new driveway gate in Johns Creek runs $5,500-$16,000 installed, with custom ornamental steel on the upper end. We build for the clay under the posts, not just the look of the gate. That means deeper footings than typical, and it means we set the hinge post dead plumb before we ever hang a leaf.
Pedestrian Gate Installation
Pedestrian gates in Johns Creek start around $4,800 for a simple steel frame with a quality lock set. We also do the access control side: keypad entry, card readers, and intercom tie-ins for communities where the pedestrian gate is part of a larger Gate Installation plan. If it’s next to a community pool or tennis court off Parsons Road, we know the HOA’s insurance expectations around self-closing hinges and latch positioning.
Sliding Gate Installation
Sliding gates make sense on Johns Creek properties with tight driveway slopes or where a swing gate would sweep into landscaping. A new automated sliding gate typically costs $6,500-$14,000 here, with the operator priced separately by brand. The thing most people get wrong: a slide gate rides on a ground track, and in Johns Creek’s clay, that track has to be set on a concrete base that won’t heave. We pour for that.
Swing Gate Installation
Swing gates remain the most common choice for the brick-front Johns Creek homes built between the late 1980s and mid-2000s. A double swing gate with automation and matching ornamental work usually lands between $8,000 and $18,500. We’re partial to hydraulic operators for the heavy stuff, and we cut the footings oversized when we know we’re hanging something that weighs half a ton. Show us the gate closing on its own and we’ll show you where it’s failing.
Security Gate Installation
Calling a gate a “security gate” means something specific to us: it closes on its own, it fails in a safe direction, and it’s wired into access control that works every time. For Johns Creek, we spec UL 325-compliant entrapment protection on every automated install: photo eyes positioned to the manufacturer’s standard, edge sensors on the leading leaf, and loop detectors sized for the driveway. A gate that looks strong but doesn’t meet UL 325 is a liability with a pretty face.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Johns Creek
We’re certified to service and install operators from LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. In Johns Creek specifically, we stock parts for the FAAC, LiftMaster, and Linear models that dominate 1990s and early 2000s era HOA entrance systems. That’s the practical advantage: when an old Elite board fries after a downtown thunderstorm, we’re not ordering a replacement from a warehouse two states away. We might already have it on the truck, which means the gate goes back up that same day. A technician stocked for the brands that actually exist in these communities will close more calls on the first visit.
Common Gate Installation Problems We See in Johns Creek Homes
- Clay heave shifts hinge posts out of plumb. Johns Creek’s red clay expands and contracts through Georgia’s wet-dry seasonal cycle, and that’s why custom ornamental gates here start leaning and binding at the latch within a few years. The fix is deeper footings, bell-bottom forms, and sometimes re-pouring the post entirely rather than shimming it.
- Summer lightning spikes destroy control boards. Johns Creek’s afternoon thunderstorms are intense, and a nearby strike on a low-voltage run frequently kills the LiftMaster or Elite board that was working fine on Tuesday. The mechanical gate is often still fine; the electronics are what gave up.
- 20-to-30-year-old operators failing in synchronized waves. Communities along McGinnis Ferry, Parsons, and State Bridge Roads were built in the same window by the same builders, which means the original FAAC and BFT slide operators are wearing out at nearly the same time. HOA budgets take the hit in clusters, not one gate at a time.
- Underground operator enclosures holding water. Johns Creek’s heavy rains expose poorly drained underground operator pits, which short out motors and corrode terminal blocks. Our installs include drainage and a lid that keeps the works dry, not just the look of the gate.
Pricing for Gate Installation in Johns Creek, GA
Here’s what we quote for Johns Creek jobs. Custom ornamental driveway gates run $6,000-$16,000 depending on size and steel work. A heavy double swing gate with hydraulic automation and UL 325-compliant entrapment protection lands at $8,000-$18,500. Pedestrian gates start around $4,800. These ranges reflect Johns Creek’s larger lots, brick-front homes, and the need for proper clay-resistant footings, which usually add $300-$700 to a post set versus what you’d pay in a flatter, sandier county.
- Pedestrian gate: $4,800-$7,500 installed
- Single swing driveway gate with automation: $6,000-$12,000 installed
- Double swing ornamental gate with automation: $8,000-$18,500 installed
- Sliding gate with track and operator: $6,500-$14,000 installed
Every quote is written and agreed before any work begins. No trip charge inside the county for estimates, $40 off any repair over $200, and seniors and veterans always get 10% off. We’ll also give you a free second opinion on any written estimate you’ve received. Call (877) 610-2993 for an exact quote on your Johns Creek gate.
One note on how Johns Creek is different: many install decisions here are made by HOA boards and property management companies, not a single homeowner. That changes the job. A board needs a written proposal that holds up to review, a defined schedule that respects school drop-off, and documentation of UL 325 compliance. A homeowner needs someone who’ll sweep the driveway when they’re done. We do both. Our crew recently installed a new FAAC 400 hydraulic swing gate operator for an HOA entrance on Parsons Road, where the original 1998 posts had drifted out of plumb in the red clay. We re-poured the hinge post footings with 24-inch deep bell-bottom forms, mounted a new LiftMaster keypad entry and loop detector, and reset the gate so the safety photocells stop the leaf dead-square before it reaches the rack. The board president checked it twice, then told us it closes quieter than the original ever did. That’s the standard we work to across Johns Creek.
We Also Serve Cities Near Johns Creek
Beyond Johns Creek, we install and service gates throughout north Fulton County. When it’s in Alpharetta, we know the commercial entrances off Windward. Peachtree Corners brings older tech parks and gated neighborhoods off Peachtree Industrial. Roswell and Milton have their own share of clay and HOA entrances. Same crew, same promise. If you’re on the edge of Johns Creek and a neighboring city, call (877) 610-2993 and ask if we cover your street: chances are we do.
Serving Johns Creek, GA - Our Local Coverage Area
We’re based in the Johns Creek area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Johns Creek
The lean comes from expansive red clay that swells when wet and shrinks when dry, gradually pushing shallow hinge posts out of plumb each season. The fix is not shimming the gate, which is what you’ll get from a drive-through installer. The gate has to come off, the post footing has to be re-poured, often with a bell-bottom form drilled 24 to 36 inches deep, and the leaf has to be re-hung. When we install new gates in Johns Creek, we size the footing for the clay from day one so the lean never gets established. Call (877) 610-2993 if a gate on your Johns Creek property is starting to bind at the latch.
The standard approach is staggered sequencing with staged temporary access. We replace one entrance at a time, keep the other entrances live, and if none can stay live for more than a few hours, we install a temporary chain-link access gate with a card reader. Most HOA boards in Johns Creek schedule this around school drop-off and pick-up times to minimize congestion. We’ll provide the written timeline and access plan so the board can circulate it to residents before we start.
UL 325 is a federal safety standard that applies to every automated gate in Georgia, and it requires continuous pressure entrapment protection on any gate intended for at least one residential dwelling and an appropriate external entrapment protection device, typically photo eyes or contact edges, on most vehicular gates. The specific requirement depends on the gate class and usage. We spec the photo eyes, edge sensors, and loop detectors appropriate for your gate so it meets UL 325 as installed, and our install documentation reflects that compliance. It is not optional here.
You can, but for a heavy double swing gate, solar means a lot of panel surface and a large battery bank, and Johns Creek’s tree cover and storm season work against small solar setups. A Ghost Controls or Mighty Mule solar kit sized for a light pedestrian gate will not cycle a 600-pound ornamental leaf all week; we see Johns Creek homeowners burn through those. For a large double gate, we recommend a hardwired operator or, if solar is truly the only option, a properly sized panel and battery system on a post set in full sun. We’ll tell you straight before you buy the wrong kit and end up replacing it in a year.
The Johns Creek-specific fix starts with surge suppression on the incoming power and proper grounding at the operator head. Summer lightning spikes travel through the low-voltage runs and into the board; the board is not defective, it’s unprotected. We add inline surge protectors, ground the operator chassis correctly, and often reroute low-voltage wiring away from long fence lines that act as lightning antennas. If the operator is on an underground system, we also open the pit and confirm it’s draining. Water plus a nearby strike kills boards faster than anything else we see in this city. Call (877) 610-2993 for a free estimate on making your Johns Creek gate storm-proof.
Call Gatewood Fence & Gate for Gate Installation in Johns Creek, GA
If you’re planning a gate installation in Johns Creek, call (877) 610-2993 for a free on-site estimate. You’ll talk to a live person. Hal Gatewood has been repairing and installing gates since 2001, the shop address is published, and his name is on every invoice. We quote before we start, in writing, and every job carries the 90-Day Done Right Promise. That’s the deal in Johns Creek and every other city we serve.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate.