Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Garland
Most gate failures in Garland aren’t the panel, the latch, or the operator. They’re the post moving in clay soil, or a weld cracking after one too many freeze-thaw cycles. That’s where we start. Gatewood Fence & Gate has been fixing gates since 2001, and we do the welding right in your driveway so the gate never leaves your property. If your gate won’t close, sags in the corner, or the operator is grinding, call us at (877) 610-2993. A live person answers, day or night, and we’ll tell you straight what’s wrong and what it’ll cost before anyone touches a tool.
Why Gatewood Fence & Gate Is Garland’s Preferred Gate Parts & Welding Company
We’re not a franchise and we don’t work out of a call center three states away. Hal Gatewood’s name is on the shop, and the shop is in the metro, down the road from Garland. That’s the oldest accountability there is. When you call about a sagging swing gate off Belt Line Road or a seized roller on a slide gate near Firewheel, the person who answers knows what Blackland Prairie clay does to a post.
Garland homeowners call us because we repair what other companies want to replace. A gate sags in the hinge post, not in the middle, and that is where we start. We published our license number, our address, and our phone. We show up in the window we promised, and every job carries the 90-Day Done Right Promise in writing. If it’s not done right, one call brings Hal back, no runaround.
Our Gate Parts & Welding team works Garland neighborhoods every week, from 75040 through 75046. We know which subdivisions have original 1970s cedar gates, which iron gates on the east side near Lake Ray Hubbard heave every spring, and which operators hold up in triple-digit heat without cooking their boards. That local knowledge means we diagnose faster, carry the right parts, and don’t make you wait on a second trip. Reviews from Garland customers consistently mention two things: we answered the phone on the first ring, and the gate still works months later. That’s the standard.
Our Gate Parts & Welding Services in Garland
Hinge Replacement
In Garland, a hinge doesn’t just wear out. It takes load from a gate that’s slowly twisting as the clay beneath the post expands and contracts. We pull the old hinge, weld or bolt a new one to plumb, and set the gate so the latch catches clean. We keep heavyweight hinges in the truck for cedar privacy gates, ornamental iron driveway gates, and wide acreage entrances. In 75043 near Lake Ray Hubbard, where soil moisture swings hardest, we see hinge screws that have wallowed out their holes by a half inch or more. A new hinge on a stripped post is a waste of money. We fix the post first, then the hinge.
Post Replacement
This is the repair that actually fixes most Garland gates. Original build posts from the 1960s through 1980s were set 18 to 24 inches deep. Blackland Prairie clay moves more than that every year, heaving 2 to 4 inches between spring rains and summer drought. The post shifts, the gate drags, the latch misses. We dig out the old footing, set a new steel post to a depth that handles Garland’s soil movement, and weld everything back square. Skip the post and you’ll fix the gate again every 18 months. We’d rather do it once.
Rail Repair
A cracked or rotted rail on a cedar gate usually shows up as a gate that droops at the far corner and drags across the concrete. On ornamental iron, it’s a weld that cracked at the rail-to-pickup joint. We weld angle-iron braces onto the back of sagging wood gates or re-weld broken iron rail joints on site. In Garland, the heat-ice cycle stresses these joints every year: triple digits from June through September dry and shrink everything, then a winter ice storm adds sudden shock load. We see cracked welds on iron gates off Rowlett Road every January after the first hard freeze. We fix the weld, not just the symptom.
Custom Welding
Not every gate can be ordered from a catalog. We weld custom gate frames, extend existing gates, build steel driveway gates to fit an odd opening, and fabricate mounting plates for operators on unusual setups. If you have a wide farm-style gate on an acreage lot along Lake Ray Hubbard or a long driveway in 75043 where a standard package gate won’t fit, we build it on site. That means measuring twice to your actual opening, not to a showroom spec. And because we weld in your driveway, you watch the work happen. No mystery shop, no hauling your gate to a facility on the other side of Dallas.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Garland
We service and stock parts for the gate operators Garland homeowners actually own: LiftMaster, FAAC, BFT, Linear, and Viking, plus Mighty Mule, Ghost Controls, DoorKing, and Elite. If your FAAC swing arm stripped a gear or your Viking slide gate is grinding, we know the failure modes for each brand in Garland’s climate. We keep common boards, limit switches, swing arms, and remotes in the truck so we can usually finish the repair in one trip. For less common parts, we order same-day from local Dallas-Fort Worth distributors. No three-week wait on a drop-ship from a warehouse in another state.
Common Gate Parts & Welding Problems We See in Garland Homes
- Clay-driven post heave in 75043 near Lake Ray Hubbard. The soil moisture swings hard on the lake side, throwing swing gates out of plumb so the latch misses the catch by an inch every spring. The panel is fine; the post is moving. We reset it.
- Heat-baked operator bearings and ice storm gear damage. Triple-digit heat bakes grease out of Viking and BFT gate operator bearings all summer, then a winter ice storm shock-loads the rack and pinion on a slide gate and strips teeth before the motor even fails. We see this every January after the first hard freeze.
- Solar gate openers losing charge on long acreage driveways. Garland’s summer haze plus winter cloud cover starves solar panels, leaving the motor dead just when a livestock trailer needs through. We size panels and batteries for Garland’s actual sun, not a showroom estimate.
- Original 1970s cedar gates drooping in 75041. Those gates were built with 18-inch post footings that were never enough for Blackland Prairie clay. Four decades later every spring pushes them a little further out of plumb. New hinges alone won’t fix it. The post has to be reset.
Pricing for Gate Parts & Welding in Garland, TX
No quote over the phone that changes when we arrive. We give upfront pricing in writing before any work starts, and the number we quote is the number on the invoice.
| Service | Typical Range in Garland |
|---|---|
| Hinge replacement (single gate) | $120-$260 |
| Hinge replacement (double gate) | $220-$410 |
| Post reset with new steel post | $350-$650 |
| Post replacement, deeper footing | $500-$900 |
| Rail repair (wood, braced) | $150-$350 |
| Rail repair (wrought iron, welded) | $180-$400 |
| Custom welding (per hour) | $95-$140 |
| Gate roller replacement | $140-$320 |
| Latch & lock replacement | $80-$240 |
Those are real ranges for the Garland market, not bait. What moves the number is the post condition, gate weight, and whether we’re welding on ornamental iron or bracing cedar. We’re happy to give you an exact number before anyone starts working. You also get $40 off any repair over $200, no trip charge inside the county, and a permanent 10% discount for seniors and veterans. A free second opinion on any written estimate, too.
We Also Serve Cities Near Garland
From our shop in the metro, we handle gate repair and welding calls in Garland and the surrounding communities: Sachse, Rowlett, Richardson, and Murphy. If you’re in one of those cities and your gate post is heaving or your operator is grinding, we’ll treat you the same way we treat Garland customers: straight answers, upfront pricing, and a live person on the phone. See our Gate Parts & Welding in Garland page for local details.
Serving Garland, TX - Our Local Coverage Area
We’re based in the Garland area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Garland
Because the post is moving, not the panel. Garland sits on Blackland Prairie expansive clay, which swells with spring rains and pushes your hinge post inward 2 to 4 inches. By August the soil shrinks and the post settles back differently. The gate is usually fine. The fix is resetting the post deeper, or sistering a new steel post beside it, then welding the hinges back to plumb. Call (877) 610-2993 and we’ll check the post before we sell you a hinge.
Yes, if the motor is in serviceable condition. We can fabricate and weld a new slide gate frame onto your existing operator’s rack and mount, provided the motor’s gear train and limit switches are still sound. On acreage entrances off 75043 we’ll also check the concrete pad and the operator’s thrust bearing, because clay movement near the lake can shift the whole assembly. If the motor is shot, we’ll tell you that plainly and quote a replacement before any welding starts. Estimates are free.
If you have utility power within reasonable trenching distance, line power is more reliable in Garland’s climate. Solar works, but you need panels and batteries sized for Garland’s summer haze and winter cloud cover, not a generic system. Most solar setups we see installed by others are undersized by about 30 percent, which is why the gate is dead on the day you actually need it. We’ll spec either option with real numbers for your driveway, not a catalog guess. Call for a measure and a written price.
Because the post footings are only 18 to 24 inches deep, and Garland’s clay soil moves more than that every year. New hinges bolted to a moving post still move. We sister a new steel post beside the original, weld or bolt the gate to plumb, and the droop stops. It’s not a hinge problem. It’s a footing problem. The gate itself is usually sound and worth keeping.
No. UL 325 requires all automatic gate operators to have a monitored entrapment protection device, which in Garland means a working safety photocell or contact edge. It’s not a bureaucratic detail. An operator without a photocell can close on a person or a vehicle. We won’t wire a gate opener without one, and we’ll refuse to jump out an existing one. If your gate came without one, we’ll add it as part of the job. Call (877) 610-2993 and we’ll get it done right.
We Start With the Post, Not the Panel
In Garland, the hinge post is the failure point far more often than the gate itself. Blackland Prairie clay heaves 2 to 4 inches between spring rains and summer drought, and many original 18-inch footings cannot resist that movement. Our crew reset a twisted hinge post on a 1978 ranch home in the 75040 corridor where the clay had pushed the post inward three inches since spring; we sistered a new steel post, welded the hinges back to plumb, and replaced a stripped LiftMaster swing arm so the gate finally closed on its own. That is the job. Not a new panel, not a part you can buy off a shelf. The post.
If your gate is pulling, dragging, or refusing to close, call (877) 610-2993. A live person answers. We’ll schedule a time that works for you, show up with the right parts, and finish the job with the gate closing true. Free estimates, written pricing before work starts, and the 90-Day Done Right Promise on every job.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Garland with on-site welding and gate repair.