Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Dallas
Gate parts and welding in Dallas usually means one of three jobs: a hinge post that has leaned out of plumb, a slide gate track that has buckled off its pad, or a weld that finally gave out after years of Texas heat cycling. Most Dallas gate repairs we see run between $160 and $480 for parts and labor, with the higher end reserved for post excavation and re-setting. We answer the phone around the clock at (877) 610-2993, and Hal Gatewood has been fixing gates in this soil since 2001. You won’t get a call center in another state. You’ll get one of us, and we’ll tell you straight what the gate needs.
Why Gatewood Fence & Gate Is Dallas’s Preferred Gate Parts & Welding Company
Dallas homeowners between Oak Cliff and East Dallas have a long memory for companies that quote low over the phone and show up with a different number. We don’t play that game. The price we quote is the price you pay, and it’s agreed before the first weld goes down. Hal Gatewood’s name is on the shop and on every invoice, and his address is published where anyone can find it. That’s the oldest accountability there is.
We’re Gate Parts & Welding specialists first. We don’t push replacement when a repair will hold. A gate sags in the hinge post, not in the middle, and that’s where we start. Dallas customers call us back because we fix the actual problem instead of swapping parts that don’t need swapping. Every job carries the 90-Day Done Right Promise in writing, not buried in fine print. If it’s not done right, one call brings Hal back. No runaround.
Our crews live and work in the Dallas area. We know the alley-facing gates in Oak Cliff, the wide ranch entrances out toward the county line, and the brick ranch homes in East Dallas where the gate has been swinging since before the interstate went through. That local knowledge saves you time and money because we show up already knowing what this soil does to a gate post.
Our Gate Parts & Welding Services in Dallas
Hinge Replacement
Dallas gate hinges fail in a predictable pattern. The Blackland Prairie clay under the hinge post swells after spring rain and shrinks during July drought, and over a few seasons the post tilts just enough to throw the gate out of alignment. The hinges then take the entire weight of the gate at an angle they were never built for. We replace worn hinge barrels and rebuild the hinge post plumb, and we don’t charge Dallas customers a trip fee inside the county.
Post Replacement
Post replacement in Dallas is different from post replacement in Fort Worth or Arlington, and any welder who has worked here knows why. The black clay soil moves every season. You can sink a post in concrete four feet deep and the clay will still heave it an inch or two over a wet winter. We dig out the old footing, re-set the post with a wider base and gravel drainage, and weld the hinge plates back on square. Then we re-hang the gate and set the swing so it clears the ground even if the post moves another fraction next year. In Dallas, a post that was set correctly five years ago often needs re-plumbing now. That’s just this soil.
Rail Repair
Gate rails on Dallas slide gates take a beating from two directions: the sun and the clay. Summer heat above 105°F expands the rail, and when the concrete pad beneath the gate has shifted from clay movement, the rail binds and bows. We straighten and re-weld bent rails, shim and re-anchor the guide rollers, and re-level the track so the gate rolls free. The common mistake is replacing the rail without fixing the pad underneath. We fix the pad first, then the rail stays straight.
Custom Welding
Some Dallas gates were built to fit a specific opening decades ago, and no off-the-shelf part will ever match. We weld on site in your driveway, which means the gate stays where it belongs and you watch the work happen. Custom welding covers broken pickets, torn hinge ears, cracked slide-gate frames, and gate-to-operator mounts that need re-fabricating. If the original weld was underbuilt as many are we cut it out and put down a proper bead. Hal welds it right the first time, and he’ll tell you if the old weld was somebody else’s sloppy work.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Dallas
We’re certified to work on nine major gate brands, and Dallas customers most often call us about FAAC, BFT, Linear, and Viking operators on their automated gates. We stock common replacement parts for these brands locally, which means less waiting for a shipped part and fewer second trips. Whether it’s a Linear actuator that’s lost its limit settings or a Viking board that fried in a surge, we service the opener without trying to talk you into a whole new system. A working gate is cheaper than a showroom gate.
Common Gate Parts & Welding Problems We See in Dallas Homes
- Swing gates dragging on the ground. The hinge post has tilted out of plumb as the Blackland Prairie clay underneath it has swelled and shrunk. Re-tightening the hinges won’t fix a post that has moved. The post has to be re-set and the gate re-hung.
- Slide gates jumping off their track. The bottom track has usually buckled or separated from its concrete pad because the clay beneath the pad shifted after rain. The real repair is releveling and re-anchoring the pad, not just replacing the track hardware. We see this constantly in the alley-served bungalow blocks of Oak Cliff and East Dallas.
- Weld failures at the hinge ears. Summer heat above 105°F expands metal gate frames and stresses the welds at the hinge attachment points. A gate that was adjusted correctly in spring rarely stays true through a full Dallas year, and a fatigued weld eventually cracks.
- Gate opener housing cracks from ice. Dallas doesn’t get many hard freezes, but when an ice storm hits, water that got into a gate operator housing freezes and cracks the casing. We replace housings, re-seal the board compartment, and re-grease the drive so the next freeze doesn’t finish the job.
Pricing for Gate Parts & Welding in Dallas, TX
Here are honest numbers for the Dallas market. Hinge replacement on a standard swing gate typically runs $160 to $320, including the new hinges and the welding to set them square. Post replacement runs $380 to $680 when the old footing has to be dug out, the post re-set, and the gate re-hung; the higher end covers wider ranch gates and posts that need a new concrete base. Rail repair and straightening usually falls between $200 and $420, depending on how far the track has moved and whether the pad needs re-anchoring. Custom welding is quoted by the job after we look at the break, but most weld repairs fall between $120 and $300. Every quote is written down and agreed before we strike an arc. Seniors and veterans get a permanent 10% discount, and any repair over $200 takes $40 off. Call (877) 610-2993 for a free estimate.
We Also Serve Cities Near Dallas
Our Gate Parts & Welding in Dallas coverage extends to the surrounding communities. We regularly work in Highland Park and University Park, where mid-century automatic gates need careful hinge and operator work. We also serve Richardson and Irving for the same gate parts, welding, and post re-plumbing jobs we handle across Dallas County.
Serving Dallas, TX - Our Local Coverage Area
We’re based in the Dallas area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Dallas
Because the hinge post has moved, not the hinges. Dallas sits on Blackland Prairie clay that swells after rain and shrinks during drought, and that cycle slowly levers the post out of plumb. You can tighten the hinge bolts all you want; the post will keep tilting until it’s dug out and re-set. That’s the most common recurring gate repair in Dallas, and it won’t stop until the post is fixed, not just the hardware. Call (877) 610-2993 and we’ll come look at the post itself.
Yes. We weld heavy farm gates in place, and we work around solar gate openers all the time on acreage properties around Dallas. The opener itself doesn’t have to come off the post while we weld, though we’ll disconnect the battery leads and the solar panel feed before we start, because welding current near a charge controller can damage the board. We’ve re-hung and re-welded wide ranch gates with solar operators in the county areas around Dallas, and the key is keeping the gate’s weight balanced so the opener isn’t fighting the hinges. We set the whole assembly square before we finish.
The bottom track has almost always shifted or buckled because the black clay under the pad moved. In Oak Cliff and East Dallas, where alley-facing slide gates are common, we regularly find the rack and pinion track has pulled away from its concrete pad after a wet spring. The fix is to relevel and re-anchor the pad, replace any bent rack section, and then reset the opener’s travel limits so it doesn’t bind next season. Replacing just the track hardware without fixing the pad means you’ll be calling us again in six months.
Usually you need a heavier roller or hinge than what the gate originally had, because alley-facing gates in East Dallas take abuse that front-entry gates don’t. The older grid-street neighborhoods in the 75204 and 75206 ZIP codes were built with rear service alleys, and a slide gate back there gets hit by garbage cans, delivery trucks, and utility workers on a weekly basis. We often upgrade the bottom rollers to a sealed-bearing style and rebuild the hinge post for a swing gate with a stronger post base. The extra cost is small compared to re-hanging the gate again after a trash truck clips it.
We set proper safety clearances on every gate we weld, and we set opener force limits and safety edges whenever an automated gate is involved. A welded gate that fits poorly can pinch fingers or close on a child or pet, so we check the gap between the gate and the post, the pinch points at the hinge, and the travel limits on the operator before we call the job done. On an automated gate, we’ll show you how the safety edge reverses the gate and set the closing force low enough that it stops on contact. If you have a welded gate in Dallas and you’re not sure it’s safe, call (877) 610-2993 and we’ll check it for free.
Call Gatewood Fence & Gate in Dallas
If your gate is dragging, jumping track, or cracked at a weld, call us at (877) 610-2993. We’ll give you a straight price before any work starts, and we’ll stand behind the repair with the 90-Day Done Right Promise. Hal Gatewood has been welding and re-hanging gates in Dallas since 2001, and he’ll tell you what the gate needs without trying to sell you a new one. The name is on the shop, and the shop is down the road. That still means something in Dallas.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Dallas since 2001.