Gate Repair in Antelope - Same-Day Repair, Priced Before We Start

Gate Repair in Antelope, CA

A gate that won’t close, drags on the concrete, or groans every time it swings is a problem that doesn’t fix itself, and in Antelope it usually gets worse fast once summer hits. Gate repair here comes down to three things most of the time: a rotted 4×4 cedar post, a warped wood frame, or an opener that quit in the middle of a 105-degree afternoon. We’re Gatewood Fence & Gate, and we fix gates the way they should be fixed, on site, without hauling yours off to a shop. Call (877) 610-2993 and a live person answers, not a voicemail.

Call (877) 610-2993

Why Antelope Homes Are Different

Antelope sits in the Sacramento Valley, and the ground here does something every July: it dries, shrinks, and pulls away from whatever is buried in it. Gate posts set in that soil work loose over a few summers, and a gate that was swinging true in May starts dragging by August. Those 6-foot cedar privacy gates on the side yards bake in 105-degree heat and then take on the wet Mediterranean winter. Wood warps. Iron hinges rust where the powder coat has worn off. The cycle repeats.

There’s another layer in Antelope that most Sacramento-area gate companies don’t deal with, and it catches a lot of homeowners off guard: the HOA. Antelope developed fast through the 80s and 90s as a planned suburban community, so a huge share of homes here sit in HOA-governed tracts. Before a single hinge gets touched, the board often has to approve the material, the color, and sometimes even the latch style. We know those streets, we know those tract homes, and we know exactly which gate hardware those builders used.

Gate Repair in Antelope

Gate repair in Antelope usually comes down to one of three things: a rotted 4×4 cedar post, a warped wood frame, or an opener that quit in the middle of a hot afternoon. Most of the gates we work on in the 95843 zip code were installed when these tract homes went up in the late 1980s and early 1990s, and they’re failing in waves now. When you call, we typically get to your Antelope home the same day for a repair, and we’ll always tell you the window before we show up. Our full Gate Repair service covers everything from hinge swaps to full post rebuilds.

Hinge and Post Repair

This is the repair we do most in Antelope. The original 4×4 cedar posts that hold up side-yard gates have been soaking up wet winters and drying out in 105-degree summers for three decades. They rot at the footing line, the post leans, and the gate sags into the latch side. Hinge post replacement runs $220 to $400 depending on how deep the old footing goes and whether the post is set in concrete or buried in dirt.

Gate Realignment

When a gate drags on the ground or won’t latch without lifting, you don’t always need new hardware. Gate realignment is common on 6-foot wood privacy gates in Antelope whose frames have warped from summer heat cycling. We can often straighten the frame, adjust the hinge offset, and reset the latch in under two hours. Gate realignment typically runs $110 to $180.

Electric and Automatic Gate Repair

Electric gate repair in Antelope often comes down to a control board baked by Sacramento Valley heat or a limit switch knocked loose by thermal swelling of the frame. We service FAAC, BFT, Linear, and Viking openers regularly out here, plus several other major brands. Electric gate repair runs $95 to $450: a limit switch swap is the low end, a control board replacement is the high end. Full opener replacement, including the arm and new safety edges, runs $900 to $1,800. The tension on high-torsion springs and moving gate panels is genuinely dangerous, so we never recommend homeowners take that on themselves. We quote the price before work starts and that’s the price, period.

Will my Antelope HOA require approval before you repair or replace my gate?

Most Antelope HOAs require written approval before any gate modification if you’re changing the material, color, or profile. A straight repair of existing hardware usually doesn’t need HOA sign-off. We’ve worked in enough Antelope communities to know the difference, and we’ll tell you up front if your project needs an architectural request form. If it does, we can prepare the spec sheet and photos so the approval goes through without delay.

Why do so many gates in Antelope neighborhoods sag at the same time?

Because they were all built at the same time, with the same hardware, from the same developers. Between 1985 and 2000, a handful of Sacramento-area builders put up whole subdivisions using identical Adjust-A-Gate brackets and 4×4 cedar posts. The posts rot at the soil line after 25 to 35 years, the brackets fatigue, and entire blocks start seeing sagging gates within a few years of each other.

Gate Installation in Antelope

A new driveway gate in Antelope typically costs $1,900 to $4,600 installed, depending on whether you need a wood pedestrian gate, a powder-coated iron swing gate, or a full sliding gate on track. Most Antelope installations take one to two days, and we schedule a free measure within a week of your call. If you live off Walerga Road, in the neighborhoods around Antelope Crossing, or anywhere else in the 95843 zip code, we know the HOA specs and county easement rules that apply. See our full Gate Installation service for details on how we build.

Driveway Gate

Driveway gates on Antelope’s tract lots usually mean one of two things: a wide swing gate across a standard suburban driveway, or a sliding gate where the driveway meets the street at a tight angle. The biggest mistake we see is a hinge post set too shallow in soil that dries and cracks every summer. We pour deeper post footings with gravel drainage so the gate does not lean come August. A single swing driveway gate in powder-coated iron runs $2,200 to $3,900 installed, depending on width and whether you add an operator.

Pedestrian Gate

Antelope homeowners often need a walk gate next to the driveway so family and delivery drivers don’t have to wait for the automatic gate every time. A pedestrian gate that has to work for years in this climate needs a hinge post set below the frost-free depth and hinges rated for at least 400 pounds. A pedestrian walk gate runs $550 to $1,200 installed. We install both wood and powder-coated iron walk gates, matched to your HOA’s material and color rules.

Sliding Gate

Sliding gates are the right answer for Antelope homes where a swing gate simply won’t fit: a short setback, a steep driveway pitch, or a shared driveway where a swing would clip the neighbor’s car. A sliding gate with rack and pinion and a Linear or DoorKing operator runs $3,200 to $4,600. Before any post is set, we check whether the county easement rules require the gate to retract parallel to the property line rather than across the shared access strip.

My Antelope HOA requires a specific powder-coated iron gate color before they’ll approve my new driveway gate. Can you match the original developer finish from the 1990s?

Yes. We match powder-coat colors by scanning the existing finish or taking a physical sample from a neighbor’s gate that the HOA has already approved. Antelope’s 1985 to 2000 tracts were built by a small group of developers, so the finish palettes repeat street after street. We verify the HOA’s current spec, match the color and sheen, and give you the match in writing before we order the gate.

Does a new automatic gate in Antelope need safety photocells even if my HOA’s rules from the 1990s don’t mention them?

Yes. California’s automatic gate safety requirements apply to every new installation and to any gate where the operator is being replaced, regardless of what the HOA’s original 1990s documents say. A new operator needs photocells or an approved edge sensor that reverses the gate if something is in the path, plus a manual release for fire access in most cases. We install UL 325-compliant safety edges and photocells on every job.

Gate Motor & Opener in Antelope

If your gate stopped opening halfway across your Antelope driveway or you’re staring at an operator that hums but won’t move, here’s the short answer: most gate motor repairs in Antelope run $180 to $340, and we can usually be at your house the same day you call. The longer answer depends on whether we’re fixing the motor itself or the 30-year-old hinges and post underneath it, which is the story of a lot of Antelope gates. Call (877) 610-2993 and we’ll diagnose it over the phone before we even roll out. Our full Gate Motor & Opener service covers swing, slide, and linear operators.

Motor Repair

This is the bulk of what we do in Antelope. Gate motors here run hard in summer heat and sit through wet winters, and the original operators on late-80s and 90s homes are failing in waves. We rebuild what can be rebuilt and tell you honestly when a motor’s control board is so obsolete it’s cheaper to replace the operator than keep patching it. A control board replacement typically runs $220 to $380 depending on the brand.

Linear Motor

Linear arm operators are common on Antelope’s ornamental iron driveway gates, especially on the higher-end streets off Antelope Road where the original developers spec’d decorative steel. We service and replace linear actuators from LiftMaster, BFT, and FAAC. When a linear motor on an Antelope gate stops holding position, the usual culprit is worn internal gears or a failing limit switch. Linear arm operator replacement runs $800 to $1,600, installed and tested.

Slide Motor

Slide gates move on a rack and rail, and in Antelope they eat Sacramento Valley dust. Long dry summers push fine grit into the rack teeth and the drive gear, causing skipped teeth and jerky travel. We clean, re-grease, and re-align the rack, replace worn drive gears, and service the motors themselves. A slide operator replacement on a typical Antelope side gate runs $1,000 to $2,200, depending on gate mass and rail length. Electrical work on these operators carries real risk, so we always recommend a trained professional handle the power side.

Why does my Antelope gate operator stop working only in late afternoon summer heat?

The most likely cause is thermal expansion in the gate panel and the operator’s internal limit switches. On a 105-degree Antelope afternoon, a metal gate can grow a quarter-inch, which pushes the limit switch out of tolerance and sends a false obstruction signal. The operator shuts down to avoid crushing something. On older LiftMaster boards original to late-80s Antelope homes, the travel-limit memory also gets unreliable after repeated heat stress.

Can I retrofit a new gate motor onto my existing 1990s iron driveway gate without HOA approval?

Usually yes, if the operator is mounted on the existing posts and the gate panel itself doesn’t change. Most Antelope HOAs care about what’s visible from the street: panel style, color, and height. A new LiftMaster or DoorKing operator bolted to the back of the existing gate generally doesn’t require architectural review. Changing the gate panel, hinges, or post style often does. We can tell you what your specific Antelope community requires.

Gate Access Control in Antelope

Gate access control in Antelope means something specific: keypads, telephone entry systems, and card readers installed onto gates that were built when the subdivision went in, 25 to 40 years ago. We outfit those aging gates with modern access control without ripping out what still works. The person who answers the phone at (877) 610-2993 is someone who knows Antelope’s streets, its HOA requirements, and the way its gates fail. See our full Gate Access Control service for system options.

Keypad Entry

Keypad entry is the most common access control request we get in Antelope, and for good reason. A hardwired or wireless keypad lets family members come and go without a remote, and lets you give a temporary code to a dog walker or house cleaner instead of handing out remotes. In Antelope, the original 1990s keypads on south-facing side gates are failing in waves: cracked rubber buttons, faded LCD screens, corroded terminals. Keypad replacement runs $290 to $480.

Telephone Entry

Telephone entry is ideal for Antelope properties where more than one family uses the same gate, especially shared driveways off streets like North Loop Boulevard and Quiet Hollow Drive. A visitor presses a call button, the system dials the homeowner’s phone, and you buzz them in from wherever you are. Telephone entry install runs $650 to $1,100. For Antelope homes with long setbacks where a visitor can’t easily reach a keypad from a car window, telephone entry solves the reach problem entirely.

Video Intercom

Video intercom gives you eyes on the gate before you open it, which matters in Antelope where many gate entry points are tucked behind privacy fences and out of sight from the house. You see who’s there on a phone app or an indoor monitor, then unlock with a tap. Video intercom runs $800 to $1,400 installed. For Antelope homes, we recommend units rated for direct sun exposure and temperatures above 110 degrees.

Do Antelope HOAs require approval before installing a keypad entry system on an existing driveway gate?

Yes, in most Antelope subdivisions the HOA’s architectural review process applies to any visible change to a gate, including new access control hardware. We’re familiar with the specific material and color specs in Antelope’s tract neighborhoods, and we integrate keypads and intercoms into existing powder-coated iron gates without altering the approved finish. That’s the difference between passing review the first time and getting a violation letter.

Will my gate access control still work during the Sacramento Valley’s 105-degree summers and winter rains?

Yes, if the equipment is rated for it and the install accounts for Antelope’s thermal cycling and wet winters. We use keypads and controllers rated for direct sun exposure above 110 degrees, and we mount, seal, and wire every outdoor connection to handle two decades of Sacramento Valley weather. Cheap hardware fails here. The brands and methods we use don’t. Call for a fixed quote on a system built for Antelope’s climate.

Gate Parts & Welding in Antelope

If you live in Antelope and your side-yard gate sags, binds, or won’t close, the problem is almost always in the hardware, not the gate itself. Gate parts and welding work in Antelope runs anywhere from $180 for a hinge replacement to $1,800 for a full post rebuild with custom welding, and most jobs are finished the same day we start. We weld on site in Antelope, in your driveway, not in a shop across town. Our full Gate Parts & Welding service keeps the gate in your yard where it belongs.

Hinge Replacement

Original Adjust-A-Gate hinges from the late 1980s and 1990s seize when Sacramento Valley winters push moisture into unpainted iron. Then the gate binds at the post and the operator strains until something gives. Hinge replacement in Antelope typically runs $180 to $340 per gate, including the hardware and labor. If the hinge plate needs to be welded because the original footprint isn’t made anymore, we handle that on site.

Post Replacement

The 4×4 cedar posts that support most Antelope side-yard gates were set in the 1980s and 1990s, and summer heat here routinely pushes past 105 degrees. The soil dries, cracks, and shrinks, and the post leans. Wooden post replacement runs $350 to $700. Galvanized steel post with custom hinge brackets runs $600 to $900. This is the single most common structural repair we do in 95843, and it’s also the one people try to patch with shims and hope, which never holds.

Custom Welding

Custom gate welding covers everything from reinforcing a sagging ornamental iron frame to fabricating a hinge bracket that matches a discontinued 1992 footprint. Custom welding jobs in Antelope generally run $200 to $700 depending on scope, and every job carries the same 90-Day Done Right Promise. A sagging ornamental iron gate usually means the hinge post has moved or the frame itself has racked from years of binding. We cut and re-weld the frame corners if needed, install a new post if the footing is shot, and hang the gate plumb.

Does my Antelope HOA require approval before I replace a rusted hinge or welded part on my 1990s iron gate?

Usually yes, and the approval is often required before work starts. Most Antelope HOA communities built in the late 1980s and 1990s have architectural review committees that must sign off on any visible hardware change, including hinge finishes and welded bracket colors. We help you navigate that process by providing a written description of the repair, the part numbers where available, and the finish color we’ll match to your HOA spec.

Can you weld a sagging ornamental iron gate back into square, or does it need a new panel?

In most Antelope cases, we can weld it back to square. It costs less than a new panel, and you keep the original iron that matches your HOA’s approved streetscape. We’ll cut and re-weld the frame corners if needed, install a new post if the footing is shot, and hang the gate plumb. The price is quoted before work starts, and that’s the price you pay.

Brands We Service in Antelope

We service nine major gate brands in Antelope, including FAAC, BFT, Linear, and Viking, plus LiftMaster, DoorKing, Elite, Ghost Controls, and Mighty Mule. We keep the most common replacement boards, arms, and hinges stocked locally so most repairs don’t wait on a shipment. See our brands for specifics.

Pricing for Gate Repair in Antelope, CA

Neighborhoods We Serve in Antelope

We get around most of 95843 on a regular enough basis that the side streets have stopped looking alike to us. The areas we work in most often include:

• Antelope Crossing area
• Woodcreek and the pocket streets around Roseview Park
• The tracts near Antelope High School and Elverta Road
• Subdivisions off Walerga Road and Antelope Road
• Quiet Hollow Drive and North Loop Boulevard

Typical response time for anywhere in Antelope is same-day when it’s a repair, and we’ll always tell you the window before we show up.

Service Area - Cities Near Antelope

We serve all of Antelope, CA plus the surrounding Sacramento Valley communities. If you’re in Foothill Farms, CA, North Highlands, CA, Citrus Heights, CA, Elverta, CA, or Rio Linda, CA, we can get to you fast. Dispatch is coordinated from our Sacramento office, and crews serve Antelope locally.

FAQs About Gate Repair in Antelope