Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Motor & Opener Across Tucker
Gate motor and opener repair in Tucker, GA typically runs $225 to $650 for most residential jobs, and we can usually have someone at your driveway within 24 hours. If your gate is humming but not moving, or it drifted out of alignment for the third time this year, the problem is often deeper than the motor itself. Call (877) 610-2993 and you’ll talk to a live person who knows Tucker’s gates, not a phone tree.
We work on gates all over Tucker, from the ranch homes off Lavista Road to the split-levels near Henderson Park and the older subdivisions around Fellowship Road. Hal Gatewood has been fixing gates since 2001, and his name is on the shop. That means something when you’re standing in your driveway looking at a gate that won’t close and you need someone who will actually show up.
If you want a Gate Motor & Opener team that treats your 1970s brick pillar and original iron gate with respect instead of trying to sell you a whole new setup, you’ve found the right crew.
Why Gatewood Fence & Gate Is Tucker’s Preferred Gate Motor & Opener Company
Tucker homeowners tell us the same story: they called a big outfit, got quoted one price, and then watched the number climb as soon as the tech backed the van into the driveway. We do it differently. Hal Gatewood owns the company, his address is published, and his license number is on every invoice. You can drive to the shop and look him in the eye if you want to. That is the oldest accountability there is.
Our team answers the phone 24/7, and it’s a live person in our office, not a voicemail or someone reading a script three states away. When you call about a gate motor in Tucker, you get a straight answer about when we can be there and what it will cost. Every job carries our 90-Day Done Right Promise in writing. If it’s not done right, we come back and make it right. No runaround, no hedge language.
We also know Tucker’s gates specifically. The brick-pillar swing gates, the sliding gate tracks buried in red clay, the control boards fried by Georgia humidity. That local knowledge means we diagnose faster and fix the actual problem instead of swapping parts that don’t need swapping.
Our Gate Motor & Opener Services in Tucker
Motor Installation
Installing a new operator on a 50-year-old Tucker gate is not a bolt-on job. The pillar may be cracked, the hinge post may have heaved, and the gate itself may weigh more than the original installer ever anticipated. We measure the gate’s weight and cycle count, check the post alignment, and match the right opener to what’s actually in your driveway. A straight forward single swing gate opener install in Tucker runs $850 to $1,500 including the operator, arms, brackets, and wiring. If your pillar needs stabilization first, we’ll tell you before we order anything, and the price is agreed in writing before work starts.
Motor Repair
Before we replace a motor, we find out why it failed. On many Tucker gates, the motor burned out because a heaved post put the rack and pinion in a bind, or a storm limb bent the frame and the operator was fighting the gate every cycle. Replacing the motor without fixing the bind means you’ll replace it again. Motor repairs in Tucker typically run $225 to $550 depending on whether we’re replacing a control board, a capacitor, a limit switch, or the motor itself. We keep common parts on the truck, so a lot of repairs happen in one trip.
Linear Motor Service
Linear operators show up on a lot of slide gates around Tucker, and most of the failures we see come down to two things: the rack has drifted out of alignment, or the limit switches have been jostled past the point where they’ll hold a setting. A lurching, half-travel slide gate on a Linear motor is almost always a rack or limit switch problem, not a dying motor. We service Linear operators across 30084 and 30085, and we stock Linear parts for same-day repairs on most common failures.
Slide Motor Service
Slide gates around Tucker have a particular enemy: red clay. The track sits low, and when clay heaves through wet and dry cycles, the track bows and the rollers bind. Then the motor stalls, the breaker trips, or the gear teeth strip. We weld and true slide gate tracks on site, which means your gate stays in your driveway instead of getting hauled off to a shop. A slide gate motor replacement in Tucker runs $600 to $1,200 depending on the operator’s horsepower and whether the track needs re-truing at the same time.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Tucker
We’re certified to service nine major gate brands, including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Around Tucker, we see a lot of Viking and Linear operators on older slide gates, and Ghost Controls kits on newer retrofit installs. We stock common boards, remotes, and limit switches for these brands, which means less waiting on a shipment when your gate won’t budge. If we can’t get a part locally, we’ll tell you exactly how long it’ll take and what it’ll cost before you decide.
Common Gate Motor & Opener Problems We See in Tucker Homes
Tucker’s combination of 1960s-1980s housing stock, red clay soil, and mature hardwood canopy creates a pretty specific set of gate failures. These are the ones we see most often:
- Heaved brick pillars and stripped gears – The original pillars around Tucker driveways were poured shallow, right into red clay. Forty years of wet-dry cycles later, the pillar has moved two or three inches, the gate is out of plumb, and the motor’s gear teeth are paying for it. A gate sags in the hinge post, not in the middle, and that’s where we start.
- Obsolete control boards on 1980s-era operators – Decades of humid subtropical moisture get inside the control box, and the old boards just quit. Sometimes we can retrofit a modern board; sometimes the entire operator has to go. We’ll tell you which one is the cheaper answer over the life of the gate.
- Storm-fallen limbs causing motor stall – Tucker’s big hardwoods shed branches during spring storms, and a limb across a gate frame can bend the metal just enough that the motor stalls or the limit switch can’t find home. We’ve replaced more bent frames and reset limit switches after spring thunderstorms than we can count.
- Gate alignment drift on original iron gates – The original ornamental iron swing gates in Tucker’s older subdivisions were never built for a modern opener. Retrofitting an operator onto a gate that’s been hanging for 50 years means the gate itself often needs sag correction before the motor has a chance. Fix the panel without the post and you’ll fix it twice.
Pricing for Gate Motor & Opener in Tucker, GA
Here’s what Tucker homeowners can expect to pay, as of this writing:
- Motor repair (control board, limit switch, capacitor, wiring): $225-$550
- Motor replacement (residential swing or slide, parts and labor): $450-$950
- Full operator installation (new motor, arms, brackets, wiring, safety eyes): $850-$1,800
- Sag correction or post stabilization (helical anchor, rack and pinion fix): $400-$900
- Emergency storm-damage repair (bent frame, stalled motor, electrical short): $350-$800
We stand by these ranges, but the only way to give you an exact number is to look at your gate. The estimate is free, it’s in writing, and the price we quote is the price you pay. Every repair carries the 90-Day Done Right Promise, and seniors and veterans always get 10% off. We also knock $40 off any repair over $200, and there’s no trip charge anywhere inside the county. Call (877) 610-2993 and we’ll put a number on it before we even touch a tool.
We Also Serve Cities Near Tucker
If you’re in Tucker or just outside it, we cover the surrounding communities too. Our service area reaches Clarkston, Mountain Park, Stone Mountain, and Chamblee, and a lot of those jobs are the same older brick-pillar gates and red clay challenges we see in Tucker. Dispatch is coordinated from our Atlanta office, but the crew that shows up at your driveway is local and accountable.
Serving Tucker, GA - Our Local Coverage Area
We’re based in the Tucker area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Motor & Opener in Tucker
It’s almost always a footing problem first. In Tucker’s older subdivisions, brick pillars were poured with shallow footings directly into red clay, and after 40 years of expansion and contraction, the pillar has migrated and taken the gate with it. You can realign the motor all day, but until the post is stabilized, it’ll keep drifting. We stabilize the footing with a helical anchor, correct the gate’s sag, and only then re-set the motor. Call (877) 610-2993 and we’ll come take a look. The estimate is free.
Yes. We do this all the time around Tucker. The trick is bracing and shimming the mounting brackets so the operator’s weight and torque don’t pull further on the cracked pillar, and sometimes we drill and epoxy an anchor through the brick into the core. The pillar may still need stabilization if it’s moving, but we can install the operator without tearing the pillar apart. Call (877) 610-2993 for a free estimate and we’ll tell you what your specific pillar needs.
Yes. Any automatic gate operator installed or significantly modified in Tucker falls under UL 325 entrapment protection standards, which means the gate must have working photocells or contact edge sensors, along with proper force settings that reverse the gate if it hits an obstruction. A lot of the 1980s-era operators we see around Tucker either predate those requirements or were installed without them. If your gate doesn’t reverse when you block it with your hand, call us. That’s a safety issue, not a convenience issue.
Usually one or the other, and we can tell which in about ten minutes. A lurch mid-travel is most often the rack drifting out of alignment with the motor’s pinion gear, especially on Tucker lots where red clay has shifted the track. If the gate travels smoothly but stops at the wrong point, it’s typically a limit switch that’s lost its setting. We handle both, plus track re-truing if that’s what the clay has done to your gate. Call (877) 610-2993 for an exact diagnosis and a free quote.
Kill the power to the operator at the breaker before doing anything else. A humming motor that won’t move usually means the gate is jammed or the capacitor has failed, and if you keep holding the button you’ll burn the motor out. Then call us. We handle storm damage calls around Tucker regularly, and we can usually have the gate moving again the same day. Call (877) 610-2993 and a live person will answer, day or night.
Call Gatewood Fence & Gate for Gate Motor & Opener Work in Tucker
If your Tucker gate is humming, sagging, or refusing to move, don’t let it sit. A gate left half open is a broken gate waiting for a worse problem, and in Tucker’s humidity, electrical problems don’t heal themselves. We’ll come to your driveway, tell you what’s actually wrong, and give you a written price before any work starts. You get the 90-Day Done Right Promise on every job, and when you call, you get a live person. Call (877) 610-2993 now. Hal’s name is on the shop, and the shop is down the road. That’s the way we like it, and that’s the way Tucker homeowners have come to expect it from us.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Tucker and the surrounding Georgia communities since 2001.