Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Motor & Opener Across Leander
If your automated gate in Leander has stopped opening, is grinding mid-travel, or only works when you nudge it by hand, here’s what to know: gate motor and opener repair in Leander typically runs $225 to $600 for a board, gear, or limit-switch rebuild, while a full motor replacement with new arms and safety edges runs $900 to $2,400 depending on gate length and whether we’re tying into existing conduit. Hal Gatewood has been fixing gates since 2001, and we’re in Leander neighborhoods like Crystal Falls, Travisso, and Bryson every week. Call (877) 610-2993 and a live person answers, day or night.
Why Gatewood Fence & Gate Is Leander’s Preferred Gate Motor & Opener Company
We’re not a franchise outfit running a crew out of a rented storage unit. Gatewood Fence & Gate is owner-operated, and Hal Gatewood’s name is on every invoice. Leander homeowners call us because we answer the phone ourselves, show up when we say we will, and fix the opener in your driveway instead of hauling the gate to a shop across town. The 90-Day Done Right Promise is stamped in writing on every job: if it’s not done right, we make it right, no runaround.
Our Gate Motor & Opener team knows what Leander’s gates go through, because we’ve watched the same failure patterns repeat across entire subdivisions. When a LiftMaster LA400 burns a control board in one Bryson cul-de-sac, we see the same sequence in the next block within a month. That’s not coincidence. It’s what happens when hundreds of builder-grade openers installed in the same 2015-2020 window hit their first major repair cycle at the same time.
We serve the full Leander area, from the 78641 corridor near Old Town to the newer 78645 and 78646 developments up Ronald Reagan Boulevard. No trip charge inside Williamson County, and every estimate is quoted and agreed before any work starts.
Our Gate Motor & Opener Services in Leander
Every opener we install or repair is matched to the gate’s weight, swing, and sun exposure, not just whatever fits the bracket holes. Here’s what we do most in Leander:
Motor Installation
A full motor installation in Leander runs $1,200 to $3,800. The spread depends on whether we’re adding automation to a manual gate (which means running power, setting posts for the operator, and wiring safety edges) or replacing a dead motor on a gate that already has conduit and a pad in place. Homes in Travisso and Crystal Falls with existing 2010s builder conduit are usually on the lower end. Homes where the builder never ran power to the gate get the full scope.
Motor Repair
Most motor repairs in Leander run $225 to $600. We rebuild stripped gearboxes, replace burned control boards, re-seat limit switches, and re-torque the arm brackets. The single most common repair call we get from Crystal Falls and Travisso is a swing arm opener that stripped its internal gear after a clay-heaved hinge post torqued it one too many times. We fix the motor and the post, because fixing only one means we see you again next spring.
Linear Motor
Linear swing arms are the standard opener on Leander’s powder-coated iron driveway gates. A new linear arm assembly including the motor, bracket, and fresh wiring runs $700 to $1,400 installed. On HOA-governed properties, we match the powder-coat finish exactly so the management company doesn’t flag the repair. We stock linear arms and control boards for Linear, Ghost Controls, and LiftMaster models common throughout Leander’s 2005-2023 housing stock.
Slide Motor
Slide gates need a different animal: a chain-drive or rack-and-pinion motor, usually ½ to 1 horsepower, with a loop detector in the driveway. A slide motor replacement in Leander runs $1,100 to $2,800 depending on gate length and whether the existing rack is still square. We re-bed the rail, re-set the chain tension, and run a full travel cycle before we call it done. The 2021 freeze killed capacitors and gearbox seals on a lot of factory slide operators around Leander’s HOA entrances, and many of those units still run but won’t hold a closed position when ice forms.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Leander
We’re certified on nine major gate opener brands, and in Leander we stock repair parts for the ones we see most: Linear, Ghost Controls, and DoorKing. If your Travisso gate came with a builder-installed Ghost Controls swing arm, we already know its failure points. If your Bryson home runs a Linear slide motor, we carry the boards and limit switches on the truck. That means less waiting for parts and more jobs finished in one trip.
Common Gate Motor & Opener Problems We See in Leander Homes
- Clay-heaved hinge posts stripping swing arms. Williamson County’s Vertisol clay expands in spring rains and contracts in the 100°F summers. When the post tilts, the swing arm’s gear takes the torque and strips. We re-set the post deeper and replace the gearbox, not just the arm.
- Builder-grade openers failing by phase. Leander’s 2010s HOA communities installed hundreds of openers from the same spec sheets. When one fails, its neighbors are usually right behind it. We see burned control boards on LiftMaster LA400s cluster by development phase, block by block.
- Missing or pinched conduit runs. In subdivisions built fast, power and low-voltage conduit often went in just under the sod. Sprinkler lines nick it, caliche cracks it, and the loop detector at the gate loses signal intermittently. We trace, re-route, and seal the run so the opener stops ghosting.
- HOA finish mismatches. Crystal Falls and Travisso architectural committees require powder-coat colors and ornamental iron profiles to match the original. We source exact-match finishes. A close-enough black is not good enough, and we’ve repaired jobs where someone else learned that the expensive way and had to redo it.
Pricing for Gate Motor & Opener in Leander, TX
Here are the ranges we quote in Leander, and the price is agreed in writing before any work begins. You’ll never answer the door to a bill bigger than the estimate.
Motor repair: $225 to $600. Linear arm replacement: $700 to $1,400. Full motor installation on a gate with existing conduit: $1,200 to $2,400. Full automation of a manual gate, including power run and safety edges: $2,000 to $3,800. Slide motor replacement: $1,100 to $2,800. Battery backup retrofits: $450 to $900. We take $40 off any repair over $200, there’s no trip charge inside Williamson County, and seniors and veterans get a standing 10% discount. Call (877) 610-2993 for a free written estimate.
We Also Serve Cities Near Leander
Our crews run gates up and down the 183 corridor. If you’re in Cedar Park, Lago Vista, Brushy Creek, or Anderson Mill, we’re close by. Gate Motor & Opener in Leander remains our home base for scheduling, and we cover the surrounding county the same week most calls come in.
Serving Leander, TX - Our Local Coverage Area
We’re based in the Leander area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Motor & Opener in Leander
Because the original builders installed spec-grade openers sized for flat, stable ground, and Leander’s clay doesn’t stay flat or stable. When the post heaves, the swing arm fights the gate every cycle, the torque limiter trips repeatedly, and the control board or gearbox gives out. We replace the opener with one sized for the gate’s actual weight and re-set the post so it stops moving. Call (877) 610-2993 and we’ll assess your gate before it leaves you stuck outside.
Yes. We trench a new power run below the caliche line, set a proper concrete pad for the operator, install the solar or AC motor, add the safety photocells, and wire it to code. It’s more work than swapping a motor on a pre-wired gate, which is why full automation runs $2,000 to $3,800 in Leander. We quote it in writing before any digging starts, and the 90-Day Done Right Promise covers the whole install.
We do it routinely. We photograph the existing finish, order the exact RAL or powder-coat match from the same suppliers the builders used, and match the ornamental iron profile on any replaced section, hinge, or bracket. Crystal Falls and Travisso management committees check this, so we treat it as part of the job, not an optional extra. A repair that gets flagged by the HOA costs you twice, and we’d rather do it right the first time.
A loop detector is a wire loop buried in the driveway that tells the slide motor when a car is sitting on the pad, so the gate doesn’t close on it. Builders sometimes skip connecting it because it adds a day to the punch list and nobody tests it at closing. We run a new loop in the asphalt or concrete, connect it to the operator, and test it with a real vehicle before we leave. A slide gate without a working loop is a safety hazard, not just a nuisance.
The cold snap likely cracked a capacitor or compromised a gearbox seal, and now the motor can’t hold torque through the full travel. It starts, loads up, and quits. We bench-test the motor, replace the failed component, re-grease the gearbox, and run the gate through 20 full cycles. Most freeze-related repairs in Leander land between $225 and $600. Call (877) 610-2993 and a live person answers, 24/7.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Leander since the company’s founding in 2001.