Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across North Bend
A new driveway or security gate in North Bend, WA typically runs $2,400 to $9,800 installed, depending on whether you’re after a manual tubular swing gate or an automated steel slide with keypad entry. Most installations take one to two days after the post concrete cures, and we schedule around the Snoqualmie Valley’s wet season so your footings set right the first time. If you’re watching a sagging farm gate or sizing up a new security gate near 396th Drive Southeast, call Hal at (877) 610-2993 for an honest price before you dig a single hole.
The real cost driver in North Bend isn’t the gate itself. It’s the ground it stands in and the wind that hits it. We’ll get into both below, because a gate spec’d for Issaquah will not survive a North Bend winter unless it’s built for saturated silt and alpine-adjacent gusts.
- Key Takeaways: manual swing gates start around $2,400; automated driveway gates with operators run $5,000 to $9,800; solid infill gates in wind-exposed areas need deeper footings and heavier posts than standard spec sheets suggest; power cuts are frequent enough in the Snoqualmie Valley that a manual release is part of every operator install we do.
Why Gatewood Fence & Gate Is North Bend’s Preferred Gate Installation Company
Gatewood Fence & Gate has been locally owned and owner-operated since 2001. Hal Gatewood’s name is on the shop and on every invoice, and he’s not shy about handing you his cell number. That matters when you live on a North Bend horse property and your gate fails at 6 a.m. with a trailer full of feed waiting behind it.
We answer every call with a live person, 24/7. Not a voicemail, not a dispatch queue, not a call center three states away. When you call about gate installation in North Bend, you’ll talk to someone who understands what the Snoqualmie River floodplain does to a post footing, because we’ve watched it happen season after season.
Our crew travels into North Bend regularly, usually same day for urgent calls. Every job we do carries our 90-Day Done Right Promise in writing: if it’s not done right, one call brings us back, no runaround. And we quote upfront, then stand by that number. No trips charges inside the county. A permanent 10% discount for seniors and veterans. $40 off any repair over $200.
Hal has been fixing gates since before half the commuter subdivisions in North Bend existed. He’s seen the good installs and pulled apart the sloppy ones. When a weld cracks or an operator bracket bends, he’d rather fix it on site than swap parts that don’t need swapping. Most gate companies in this trade replace. We repair first, replace when it’s actually necessary.
Our Gate Installation Services in North Bend
We install gates that match North Bend’s property types: long rural driveways, equestrian entries, and the occasional commuter home off Exit 31. All of our work starts with a conversation about how you actually use your gate, because a horse property gate and a security gate on a subdivision lot shouldn’t be built the same way.
Driveway Gate Installation
A driveway gate in North Bend usually spans 12 to 20 feet across the entry, and on the multi-acre parcels east of town that often means a heavy tubular steel frame mounted on posts you could hide a fence post inside. We size the operator to the gate’s weight and wind load, not the other way around, because a gate that catches Snoqualmie Pass wind like a sail will kill an undersized opener in two seasons. We also install keypads and vehicle sensors so you don’t climb out of the truck in flood-season mud if you don’t have to.
Pedestrian Gate Installation
Pedestrian gates are the side door of the property, and in North Bend they’re often attached to post-and-rail horse fencing or a cedar privacy fence that’s been through a few valley winters. We hang them on oversized hinges, set the post deeper than code minimums in silty ground, and add a latch and closer that can handle repeated slamming from kids and horses alike. A pedestrian gate should never be an afterthought; if the post wanders, the latch stops catching, and then you’re climbing over your own fence.
Sliding Gate Installation
Sliding gates make sense where the driveway has no swing room, or where a swing gate would catch too much wind on a solid panel. In North Bend, sliding gate track gets buried in fine silt and gravel, so we set the track on a compacted base and spec a V-track or cantilever system where the grade allows. If your property sits in the floodplain, we’ll steer you toward a cantilever slide and raise the track above grade so the next river flood doesn’t jam the wheel.
Swing Gate Installation
Swing gates are the workhorse of the Snoqualmie Valley. We install single-leaf and double-leaf swing gates across North Bend every week, from 10-foot farm entries to 22-foot double drives with an opener on each leaf. The post is the job. We re-pour footings with deeper embedment and rebar, then let the concrete cure fully before hanging the gate. Show us a swinging gate that sags, and we’ll show you a hinge post that moved. Fix the panel without the post and you’ll fix it twice.
When we install a swing or driveway gate, we also set up the manual release and show you how to use it. The valley loses power during storm cycles, and a gate you can’t open manually is a fence that locks you out of your own driveway. Gate Installation for us means the gate works in the dark, in the rain, and with the power out.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in North Bend
We’re certified to service and install nine major gate brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. For North Bend customers, that matters because BFT and FAAC operators hold up better in wet, cold conditions, and Viking hydraulic arms are a common choice for heavy equestrian gates. We keep common boards, brackets, and replacement parts in the truck, so a service call into North Bend doesn’t turn into two trips because somebody didn’t stock a FAAC limit switch. If your current opener is failing and a full replacement is on the table, we’ll give you an honest recommendation based on how the gate is built and how often it cycles.
Common Gate Installation Problems We See in North Bend Homes
- Solid infill gates bending under storm wind. A solid panel that looks great in the brochure acts like a wall in a Snoqualmie Valley wind event. We see frames bowed and hinges torn out after the first winter. The fix is a heavier frame, larger hinge posts, and sometimes redesigning the gate to let air pass through.
- Gate posts leaning in saturated soil. North Bend’s valley floor sits on silty bottomland that resaturates after every flood cycle. When the ground shifts, the post walks, and the gate starts dragging on its latch. We reset posts with deeper embedment and a wider concrete collar than a standard spec calls for.
- Rust and corrosion on hinges and latches. The Snoqualmie Valley keeps gate hardware in near-constant humidity for eight months a year. Untreated hinges and cheap latches rust through faster here than they would 15 miles west. We spec galvanized or stainless hardware on North Bend installs, and it costs a little more up front, and it is the difference between a five-year gate and a twenty-year gate.
- Undersized operators on long driveway gates. A gate on a multi-acre lot might cycle ten times a day with trailers, delivery trucks, and farm equipment. Operators sized to a suburban gate quit early under that load. We calculate the duty cycle before recommending an opener, and we won’t sell you a residential opener for a gate that sees commercial traffic.
After a winter storm cycle off Snoqualmie Pass dropped heavy wet snow, our crew reset a leaning hinge post on a tubular steel swing gate off 396th Drive Southeast, where saturated ground had heaved the post footing. We re-poured the footing with deeper embedment, replaced the bent FAAC operator bracket, and added a keypad entry so the owner could avoid leaving the truck in flood-season mud. That’s a typical North Bend call in February.
Pricing for Gate Installation in North Bend, WA
| Installation Type | Typical North Bend Range |
|---|---|
| Manual tubular swing gate (single leaf) | $2,400 - $4,200 |
| Automated steel driveway gate (single leaf, opener included) | $5,000 - $7,800 |
| Double-leaf swing gate with dual operators | $7,500 - $9,800+ |
| Sliding gate (V-track or cantilever) | $6,200 - $9,500 |
| Pedestrian gate | $700 - $1,900 |
The price you’re quoted is the price you pay. We walk the site, measure the opening, talk through your options, and give you a written number before any work starts. If the ground is soaked or the existing post is rotted below grade, we’ll tell you up front and include that work in the quote, not tack it on after the crew shows up. Hal hates surprises on invoices as much as you do. Call (877) 610-2993 for a free estimate, and ask for the senior or veteran discount if it applies.
We Also Serve Cities Near North Bend
Our gate installation team covers North Bend and the surrounding communities: Snoqualmie, Hobart, Issaquah, and Klahanie. If you’re just over the river or up the hill and need a gate looked at, the same crew and the same 90-Day Done Right Promise applies. Dispatch and scheduling are coordinated from our Seattle office, but crews serve North Bend locally and are on the valley roads throughout the week.
Serving North Bend, WA - Our Local Coverage Area
We’re based in the North Bend area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in North Bend
Every automated gate we install in North Bend has a manual release key or lever, usually on the operator itself. For BFT and FAAC arms, there’s a keyed release that disconnects the actuator from the gate leaf, so you can push the gate by hand. For FAAC swing arms, the release is built into the gate’s drive arm. We show you where it is and how to use it during installation, and we recommend you test it once before winter. If your gate doesn’t have a working manual release, call (877) 610-2993 and we’ll get that fixed. You should not be trapped behind your own gate when the Snoqualmie Valley grid goes down.
For a solid infill swing gate on a North Bend property, we pour footings 36 to 48 inches deep with a 16 to 24 inch diameter, depending on the gate’s square footage and wind exposure. A 16-by-7-foot solid panel catches more wind than most people realize, and a post set in saturated silt needs the extra embedment and concrete mass to hold. On floodplain lots, we over-excavate and add compacted gravel below the footing so water drains away from the post base. We’ll spec the exact footing for your gate after measuring the opening and checking the soil, but the short version is: deeper than a standard residential install.
Solar openers work in North Bend, but only if the panel gets direct sun for most of the day. On properties under the tree canopy along the middle fork of the Snoqualmie, or with south-facing panels shaded by the Cascade foothills, a solar panel sized to the opener’s spec will underperform. We’ve fixed enough dead solar systems to know that a small panel is a false economy. The practical answer is to run low-voltage AC to the gate if power is close, or oversize the solar array and battery bank. We’ll tell you honestly which route makes sense for your property.
A sliding gate binds after a flood because silt and fine sediment wash over the track and wheels, and the gate’s weight then grinds against a packed layer of debris. On North Bend properties in the floodplain, this happens after nearly every significant Snoqualmie River flood event. The track either needs to be cleaned and the wheels re-seated, or the gate needs to be raised on a higher rail or converted to a cantilever system that doesn’t ride on a ground track at all. If your sliding gate is stiff or squealing after a flood, call (877) 610-2993 and we’ll diagnose it, often same day.
UL 325 entrapment protection should be tested monthly, and we recommend North Bend homeowners test it every two weeks during the wet season, when photo eyes get muddied, ground loops shift, and the freeze-and-thaw cycles mess with the safety edges. A gate that reverses on pressure when your grandkid stands in the way is doing its job. A gate that doesn’t reverse is an emergency. We test and adjust entrapment protection on every service call and every new install, and we’ll show you how to run the reverse test so you can do it between visits. If your operator fails the reverse test, call us before someone gets hurt.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate. Locally owned and owner-operated since 2001, with a published address and license number anyone can look up.
Ready to Get Your Gate Done Right in North Bend?
Call (877) 610-2993 today for a free, written estimate on gate installation in North Bend, WA. We’ll come out, look at your entry, give you an honest number, and answer the phone when you call. The name is on the shop, and the shop is covered by the same rain you are. That’s the oldest accountability there is.