Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Hendersonville
A new driveway gate in Hendersonville typically runs $4,200-$9,800 installed, depending on whether you need a single swing gate, a double swing, HOA-approved finishes, or lakefront post work. Most residential installations wrap up in one to two days once materials are on site, and every job carries our 90-Day Done Right Promise in writing. Hal Gatewood has been putting gates in across Middle Tennessee since 2001, and the Hendersonville work we do reflects the same standard we’d put on our own driveway. Call (877) 610-2993 and a live person picks up, day or night.
Hendersonville is its own animal when it comes to gate work. The lake corridor running through Rockland Estates, Walton Ferry peninsula, and the subdivisions off Saundersville Road puts more moisture on gate hardware than almost anywhere else in the metro. We plan for that before we ever pour a post footing. If you’re in a lakefront neighborhood, you need a gate installer who knows what Old Hickory Lake does to steel and who doesn’t treat Hendersonville like just another Nashville suburb.
Key Takeaways
- Gate installation in Hendersonville runs roughly $4,200-$9,800, with HOA finishes and lakefront soil conditions affecting the final number.
- Hendersonville’s humidity and lake-adjacent soils mean post footings here need to go deeper than they would in Brentwood or Franklin.
- Most HOAs in Hendersonville require architectural review before a new gate goes in. We help with that paperwork.
- We stock parts for FAAC, BFT, Linear, and Viking operators, so a replacement part doesn’t mean a two-week wait.
- Every job is quoted before work starts. The price we agree on is the price you pay.
Why Gatewood Fence & Gate Is Hendersonville’s Preferred Gate Installation Company
Hendersonville homeowners tend to check a company out before they schedule. They want to know the name on the invoice matches the person who shows up. Ours does. Hal Gatewood owns Gatewood Fence & Gate, his address is published, and his license number is available to anyone who asks. That’s rare, and around here it matters.
We answer the phone with a live person, 24/7. Not a phone tree. Not a call center two states away. When you call about a sagging gate off New Shackle Island Road or a dead operator in Durham Farms, you talk to someone who can actually tell you when the crew will be there and what to expect. Scheduling for Hendersonville work is coordinated from our Memphis office, but the people doing the installation are local crews who know the roads, the soil, and the building departments.
Every job we put in carries the 90-Day Done Right Promise in writing. If something isn’t right, one call brings Hal back. That’s not fine print. It’s stamped on every invoice. We also offer $40 off any repair over $200, no trip charge inside the county, a free second opinion on any written estimate, and a 10% discount for seniors and veterans. Background-checked, uniformed people show up at your door. The same face you’ll see at the Ace Hardware on Indian Lake Boulevard next week.
The HOA Reality: What Hendersonville Homeowners Face Before the Gate Goes Up
Before we ever order steel for a Hendersonville gate, there’s usually a meeting. Not with us, with your HOA. Most of the subdivisions along Old Hickory Lake, and a good chunk of the 1970s-to-2000s neighborhoods inland, have architectural review committees that have to sign off on gate style, height, finish color, and in some cases the exact operator model. Indian Lake, Fairvue Plantation, Durham Farms, Rockland Estates. The names change. The process doesn’t.
That’s where we end up doing work most national companies won’t. We’ll sit with the management company. We’ll put together the spec sheet for the committee. We’ll match the finish to the architectural standard, whether that’s a dark bronze on ornamental steel in a lakefront subdivision or a flat black tubular gate in a neighborhood with a simpler standard. Most importantly, we don’t get halfway into the job and tell you that your HOA needs a form you’ve never heard of. We know this routine. We have one goal: keep the gate moving forward and make approval the least stressful part.
Shared Entry Systems and Access Control
Hendersonville has a big inventory of HOA-governed community entrance gates from the 1990s subdivision boom. Those old slide gate operators are now 25 to 35 years old and failing at the worst possible times. January ice storm, resident trying to get through on a delay, and the motor overloads against a frozen seal. We replace those with modern slide gate operators sized for continuous duty, pair them with vehicle detection loops and photocells, and work directly with the property manager on resident access integration, including keypads, telephone entry, and HOA-managed remote systems. We install LiftMaster, FAAC, BFT, Linear, and Viking equipment, and we can usually have the new operator running the same day we get approval.
Our Gate Installation Services in Hendersonville
If you’re in Hendersonville and looking at a new gate, you’re probably not sure whether you need a swing, a slide, or something smaller for a side yard. Here’s what we actually install in this city, and what matters for each on a Hendersonville property. Our full Gate Installation team handles every one of these, from first measurement to final walkthrough.
Driveway Gate Installation
Driveway gates are the bulk of what we install in Hendersonville, and the biggest variable is how close you are to the lake. On most lots in the 37075 and 37077 zip codes, we recommend a galvanized steel frame with a powder coat, because the humidity off Old Hickory Lake works through untreated steel in a few seasons. A single driveway gate on a standard Hendersonville lot runs roughly $4,200-$6,500. A double gate on a wider driveway runs $6,200-$9,800. If your property slopes toward the road, we’ll talk about swing direction and operator choice before anything gets welded.
Swing Gate Installation
Swing gates are the most common gate type in Hendersonville, especially in the 1990s neighborhoods where ornamental iron was the standard. The critical piece here is the post. Hendersonville’s lake-adjacent soil expands and contracts with the water table, and a post set at shallow depth will lean within a few years, which drags the gate and burns out the operator we installed. We set swing gate posts at depths we’ve learned through two decades of fixing what other installers got wrong. A single swing gate with a Linear or LiftMaster operator runs $3,800-$6,200, and a double swing runs $5,800-$8,900.
Slide Gate Installation
Slide gates matter more in Hendersonville than people expect. A lot of homes on the peninsula lots off Walton Ferry Road or along the lake have driveways with a steep approach or gravel tracks where a swing gate would bind. A cantilever slide gate rides clean over uneven ground and doesn’t drag in the heavy clay we get here after winter rain. Slide gate installations run $5,500-$9,500 depending on track length and whether we need to run conduit for a new operator. We also replace a lot of 1990s slide gate operators in HOA shared entry points, which freeze up in January and February because they were never sized for ice loading. We’ll always match the replacement to the existing track and resident access setup, so you’re not buying electronics you don’t need.
Pedestrian Gate Installation
A pedestrian gate alongside a driveway gate or a fenced side yard is usually a simpler job, but the HOA finish requirements still apply. We install matching pedestrian gates in tubular steel or ornamental iron with the same finish as the driveway gate, so the whole elevation looks like it was planned. A typical pedestrian gate in Hendersonville runs $1,400-$2,800. If you want a mag lock or keypad on it, we’ll do that at the same time and avoid a second trip.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Hendersonville
We’re certified on nine major gate brands, and for Hendersonville customers we keep parts local where it matters. If a FAAC board fails on a lakefront gate, you don’t want to wait a week for shipping while the gate sits open. We stock replacement boards, arms, sensors, and remotes for FAAC, BFT, Linear, and Viking, which covers a large share of the equipment running in Hendersonville subdivisions right now. That means a faster fix on the day we come out, not a quote on Wednesday and a part on Monday. If your existing gate is one of these brands, we can usually match the new work to what’s already on your controller, saving you the cost of a full electronics swap.
Common Gate Installation Problems We See in Hendersonville Homes
- Moisture-accelerated rust at the hinge post. The lots within a few blocks of Old Hickory Lake carry morning fog almost daily during spring and fall. Condensation collects at the hinge post base where paint has chipped, and the steel rusts from the inside out. We see this more in Rockland Estates, Walton Ferry, and the lake side of Saundersville Road than anywhere else in Sumner County.
- Post lean from saturated, shifting soil. Lake-adjacent land breathes with the water table. A 4×4 steel post set in a standard 36-inch footing will lean in three or four years, and the gate starts dragging the ground on one side. By the time a homeowner calls us, the operator has been working against that resistance and often needs replacement too. We fix the post first, then check the electronics.
- HOA entrance gate operators failing in ice storms. Hendersonville’s January and February ice events coat the gate track and wrap around the operator arm. The old 1990s slide gate operators in shared entry systems overload against a frozen seal and trip or burn. We replace those with rated operators that handle the load here. This is a pattern we see at Fairvue Plantation, Indian Lake, and in older HOA neighborhoods on the west side of 31E.
- Freshly installed gates that don’t match HOA finish codes. We get called in when a gate has already been installed by someone who didn’t check the architectural standards. The finish is wrong, the height is wrong, or the gate doesn’t match the existing streetscape. We do a lot of repairs on gates that were installed badly the first time. If you’re about to install one, let us handle the approval so you don’t end up on our repair list.
The Lakefront Gate Installation Playbook
Hendersonville sits along one of the longest stretches of Old Hickory Lake shoreline of any single city in Tennessee. That’s a geographic fact, and it shapes every gate we install within a few blocks of the water. Gate posts, hinges, and operators on these lots face constant high humidity, morning fog, and soil that moves with seasonal water levels. The result is moisture-accelerated rust, motor seal failures, and post lean that inland suburbs like Brentwood or Franklin rarely see. A gate that would last 15 years in Franklin may last 8 years on a lakefront lot here unless we engineer for the lake from day one.
We installed a new swing gate on a Rockland Estates lakefront property where the original iron gate’s hinge post had leaned so badly the gate drag could burn out the operator. Our crew reset the post with a deeper concrete post footing and replaced the rusted hinge post assembly with a tubular steel double gate, then paired it with a LiftMaster gate operator and safety photocells. The homeowner’s HOA required a dark bronze finish to match the subdivision’s architectural standard, so we used a marine-grade powder coat that will hold up in the daily fog off Old Hickory Lake. Post depth and finish aren’t things you think about when you’re first shopping for a gate. They’re exactly what decides whether the gate is still level in five years.
Pricing for Gate Installation in Hendersonville, TN
| Gate Type | Hendersonville Typical Range |
|---|---|
| Pedestrian gate (steel, installed) | $1,400-$2,800 |
| Single swing driveway gate with operator | $3,800-$6,200 |
| Double swing driveway gate with operator | $5,800-$8,900 |
| Slide gate (cantilever, residential) | $5,500-$9,500 |
| HOAs or shared entry slide gate operator replacement | $2,200-$4,800 |
These are honest numbers for the Hendersonville market, not a teaser to get us in your driveway. The price you’re quoted is the price you pay, agreed before any work starts. What moves the number here is finish requirements from your HOA, post footing depth for lake-adjacent soil, and whether we’re matching an existing control board or installing fresh. Estimates are free. Call (877) 610-2993 and we’ll come measure, then put the price in writing.
We Also Serve Cities Near Hendersonville
Our crews work up and down the Sumner County corridor, so if you’re in Goodlettsville, Millersville, Green Hill, or Mount Juliet, we can reach you from our Hendersonville service area without a long haul. We also handle the broader Gate Installation in Hendersonville area, including every HOA and lakefront community in the 37075 and 37077 zip codes. Same owner, same promise, same live person on the phone.
Serving Hendersonville, TN - Our Local Coverage Area
We’re based in the Hendersonville area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Hendersonville
A marine-grade powder coat over galvanized steel is the standard we recommend for any Hendersonville property within a few blocks of Old Hickory Lake, and most lakefront HOAs will require a specific finish, usually dark bronze or black, to match their architectural guidelines. Galvanized steel alone, without a proper powder primer and topcoat, will rust at the hinge post within a few seasons here. We’ll match the finish to your HOA’s standard and give you the exact specification before installation. Call (877) 610-2993 for a free lakefront gate estimate.
Yes, in most Hendersonville subdivisions it does. Communities like Fairvue Plantation, Durham Farms, and Rockland Estates have architectural review committees that must approve gate style, height, finish, and often the operator model before work starts. We handle the documentation and work directly with your management company. If you’re unsure whether your neighborhood requires approval, call us with your subdivision name and we’ll tell you what the process looks like. Call (877) 610-2993.
Usually a new post, not a new operator. Leaning gates on lake-adjacent Hendersonville lots happen because the soil shifts with the water table, and the original post wasn’t set deep enough. The drag burns out the operator over time as a secondary failure. We fix the post reset first, re-hang the gate, then test the operator to see if it survived. Replacing the operator before the post means you’ll replace it again in two years. Call (877) 610-2993 and we’ll come look at it the same week.
A properly sized operator will, especially if we install it with the right torque and the gate swings clear of ice buildup. The January and February ice storms in Hendersonville are a known failure point for older 1990s slide gate operators in HOA entrance systems, which often weren’t rated for frozen seal loading. We spec operators for ice conditions here, including intermittent duty upgrades for shared entry gates. If your current operator dies during a freeze, call (877) 610-2993 and a live person answers 24/7.
Yes, and it’s a popular option in Hendersonville where a conventional power run to the gate would mean trenching across a long driveway or disturbing an HOA-managed landscape. We install solar-compatible operators from LiftMaster, FAAC, and Viking, with the panel sized for Middle Tennessee’s winter cloud cover, not just summer sun. A solar system costs more upfront but makes sense on larger Hendersonville lots and lakefront driveways where running conduit gets expensive. Call (877) 610-2993 for a free measure and a written price.
Ready to Get Your Hendersonville Gate Installed?
Call (877) 610-2993. A live person answers, day or night. We’ll schedule a free measure in Hendersonville, put a written estimate in your hands before anything gets started, and if you need HOA approval, we’ll help with that too. The name is on the shop, and the shop is down the road. That’s the oldest accountability there is.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Hendersonville since 2001.