Gate Repair in Fort Worth - Same-Day Repair, Priced Before We Start

Gate Repair in Fort Worth, TX

Gate repair in Fort Worth is a job you can’t put off. A gate that drags on the driveway or won’t close at all means a car blocked in, a dog that can get loose, and a front entrance that can’t be secured overnight. We fix gates all over this city, and the work here is different from anywhere else in Texas because of what’s under the ground. Fort Worth sits on Blackland Prairie clay that heaves posts out of plumb every wet spring and contracts hard in the summer, so a gate that worked fine in March is dragging by August. Call (877) 610-2993 and a live person picks up, day or night.

Call (877) 610-2993

Why Fort Worth Homes Are Different

Fort Worth sits on expansive shrink-swell clay, and that single fact shapes more gate work here than any other variable. When spring rains soak the ground, the clay swells and pushes gate posts out of alignment. Then the baking-dry summers pull the moisture back out, the clay contracts hard, and posts lean further. That cycle repeats every year, which means older iron gates in neighborhoods like Fairmount, Ryan Place, and the west-side 76107 estates are constantly fighting the soil beneath them. No neighboring city on sandier ground deals with this the same way.

Add in Fort Worth’s deep ranching identity, and you understand why ornamental iron driveway gates and pipe-style ranch gates dominate here far more than in Dallas or the Houston suburbs. The most common call we run is iron hinge and pivot repair plus post realignment, not the wood-privacy-gate work you’d see in peer Texas metros. North Texas ice storms add another layer. Winter Storm Uri in February 2021 coated Fort Worth’s gates and openers in heavy freezing rain that snapped hinges and seized gear-drive motors, and we still find water intrusion inside operators that “worked fine” until that week.

Gate Repair in Fort Worth

Gate repair in Fort Worth usually comes down to one of three things: a post that’s moved in the clay, a hinge that’s rusted through, or an operator that’s fighting the first two. We start every repair by checking the post, because that’s where the problem actually lives. Fix the panel without the post and you’ll fix it twice. Our Gate Repair work is done on site, with welding done in your driveway rather than hauling your gate off to a shop.

Electric Gate Repair

When an electric gate in Fort Worth stops responding, we check the operator, the loop detector, and the gate itself before touching anything. We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule operators, including older gear-drive motors that ice storms like the February 2021 event seized up hard. Corrosion builds inside the housing, limit switches drift, and the gate loses its stop position. We open it, clean it, test it, and get it running without swapping parts that don’t need swapping. Most electric operator repairs in Fort Worth fall between $225 and $550 for boards, limit switches, or gear work.

Hinge & Post Repair

Here’s what we see most in Fort Worth: a wrought iron gate starts sagging, the homeowner assumes the gate itself bent, and a handyman welds a diagonal brace onto it. The gate wasn’t bent. The post moved. We re-set posts in new concrete, reinforce hinge mounts with steel plate, and weld broken hinge barrels on site. Resetting a leaning post with fresh concrete runs $400 to $800 depending on post size and how much old footing we have to break out.

Gate Realignment

Fort Worth’s clay swells in spring and bakes dry in late summer, and the result is a gate that drags in June and catches by August. It’s not poor construction in most cases. It’s the Blackland Prairie doing what the Blackland Prairie does. We realign the gate at the hinges, re-shim the operator travel, and torque all bolts. In the 76107 and 76110 zip codes specifically, nearly every older iron gate we service has moved since it was first hung. Full gate realignment with hinge and weld touch-ups runs $250 to $500.

How fast can you get to my Fort Worth home?

In most Fort Worth neighborhoods we can have a repair person at your gate the same day you call, and a live person answers the phone 24/7. Tell us what the gate is doing and we’ll give you a straight arrival time before work starts. Call (877) 610-2993.

Can you repair a gate that was damaged in a Fort Worth ice storm?

Yes, and it’s one of the most common calls we get after North Texas freezes. Freezing rain seizes gear-drive motors and snaps rust-weakened hinges. We carry replacement gears, control boards, and hinge stock locally so ice-damage repairs don’t wait on an out-of-state distributor.

Gate Installation in Fort Worth

Gate installation in Fort Worth runs about $1,200 to $4,800 for a standard automatic driveway gate, with ornamental iron estate gates in places like Crestline or Berkeley Place starting closer to $6,500 and climbing from there. Most installations take one to three days once materials arrive, depending on whether we’re building on flat clay at the street or working a sloped lot. We quote the job before any work starts, and the quote does not change at the door. For a full look at what’s involved, see our Gate Installation page.

Driveway Gate Installation

A driveway gate in Fort Worth is not a weekend project. The post footings have to be dug below the active clay zone or the gate will tilt before the next spring. We size the operator to the gate’s actual weight, set hinge posts on engineered footings, and if the driveway is sloped or tight, we’ll talk through swing versus slide before any concrete is poured. Most driveway gate installs in 76107, 76108, and beyond start around $1,400 for a basic single swing and run higher for custom work.

Sliding Gate Installation

Sliding gates make sense on Fort Worth properties where the driveway climbs away from the road or dips at the approach. Instead of fighting gravity with a swing leaf, the gate rolls on a track. We use cantilever style where possible so rollers don’t pack with clay mud. A powered slide gate on a standard Fort Worth residential lot usually lands between $2,800 and $6,500 depending on length, automation, and whether we’re cutting the driveway for conduit.

Swing Gate Installation

Swing gates remain the most common choice in Fort Worth, especially the ornamental iron styles you see across Crestline, Monticello, and Berkeley Place. We build the leaf to the driveway’s width, spec the operators for the gate’s real weight, and set posts so the hinges won’t bind as the ground moves. A single ornamental iron swing gate with automation in a Fort Worth estate neighborhood is generally $3,500 to $8,000 when we’re fabricating the gate itself.

Why do gate posts in Fort Worth need re-plumbing so often after an installation?

Because Fort Worth sits on expansive shrink-swell clay that heaves upward when spring rains soak the ground and contracts sharply during summer drought. That cycle puts lateral pressure on every gate post, even ones set in concrete, and a post installed without proper depth or rebar will tilt within a year. We dig Fort Worth post holes below the active clay zone and use reinforced footings sized to the gate.

Do automated gates in Fort Worth need special protection against ice storms?

They do. Freezing rain, not manageable snow, is what takes Fort Worth gates down. The February 2021 storm coated gates in heavy ice, snapped hinge pins, and seized gear-drive motors. We spec operators with cold-weather capability and battery backup for Fort Worth installs, and we set force and travel limits so the operator isn’t fighting ice load the next freeze.

Gate Motor & Opener in Fort Worth

When a gate motor dies in Fort Worth, the clay soil has something to do with it, and so does the age of the iron. A gate stuck open on a Tuesday morning in Ryan Place isn’t the same job as one that won’t budge out near 76108. We’ve been fixing gate motors and openers all over this city, and we start every motor job by checking the post and hinges before we ever touch the operator. See Gate Motor & Opener for the full scope of what we handle.

Motor Installation

Installing a gate motor in Fort Worth is never just bolting a box to a post. The post itself has to be plumb and set right, or the operator fights the geometry from day one. We handle full installations for swing and slide gates, running the power, mounting the operator, installing safety photo eyes and edges, and programming remotes and keypads. In neighborhoods like Berkeley Place and Crestline, where the ornamental iron is 40 or 50 years old, we often realign or reinforce the post before the new motor goes on. A full operator installation on a sound gate runs $1,100 to $2,800 for swing gates and $1,400 to $3,200 for slide gates.

Motor Repair

Most gate motor repairs in Fort Worth are cheaper than people expect once somebody actually opens the housing. A board replacement on a common swing operator runs $220 to $450. A gear or sprocket swap runs $180 to $320. Limit switch issues, which cause gates to open halfway and reverse or refuse to close, often run under $200 with parts and labor. Too many companies won’t open the unit at all. They quote a whole new operator because it’s easier for them. We repair first.

Linear Motor Service

Linear arm operators are everywhere in Fort Worth, especially on the swing gates common to estate neighborhoods west of downtown and ranch-style entrances on the north and east sides. These units work hard in the summer heat, and the worm gears inside wear down faster when the gate is even slightly out of balance. We diagnose and rebuild Linear arms, replace worn gears and capacitors, and reset travel limits that drift over time. A Linear gear-and-cap rebuild in Fort Worth typically runs $250 to $480.

How fast can you get to a gate emergency in Fort Worth?

We answer the phone live 24 hours a day, seven days a week, and we schedule Fort Worth calls based on urgency, not a queue. A gate stuck open is a real emergency if you have kids, dogs, or a shop full of tools behind it. In most cases we can have someone out same day. Call (877) 610-2993 and tell us what’s happening.

Do you come out at night or on weekends for gate motor problems in Fort Worth?

Yes. A gate that won’t close at 10:00 p.m. is a security problem, not a convenience problem. We take calls around the clock and don’t route you to an answering service. In Fort Worth’s older neighborhoods, where driveways open directly onto busy streets and the iron is older and more failure-prone, we get overnight calls in every season.

Gate Access Control in Fort Worth

Gate access control in Fort Worth usually means one of two things has gone wrong: the keypad stopped reading your code after the last big storm, or the gate motor runs but the phone entry system won’t let your delivery driver through. We fix both, and most access control repairs in Fort Worth are handled same-day. The full breakdown is on our Gate Access Control page.

Keypad Entry

Most Fort Worth keypad failures we see are weather-related. Rain gets past a cracked membrane or sun-baked gasket, and the pad registers ghost presses or none at all. We replace keypads, reflash codes, and when the wiring between the pad and the main board has corroded from years of Tarrant County humidity, we pull new low-voltage line rather than patching a wire that will fail again in six months. A basic keypad replacement in Fort Worth runs $180 to $320 on average.

Phone Entry

Phone entry systems let you buzz a visitor through from your cell, and in Fort Worth they get flaky most often after hot summers, when the cellular module in the box overheats and drops its connection. We install and troubleshoot phone entry for Fort Worth driveways, including two-wire systems common on older ornamental gates in Fairmount and Berkeley Place. A new phone entry module runs $300 to $480 installed depending on whether you need a new antenna or cellular board.

Card Reader

Card readers show up on a lot of Fort Worth properties that share a gate, like duplexes, small offices, and the occasional alley-access gate in established neighborhoods. We install proximity readers, key fob systems, and standalone card readers for gates that HOA rules or city code require to stay self-latching. A single card reader install runs $280 to $450; adding a second reader or keypad at the same gate usually adds $150 to $250.

Can you fix my access control emergency today in Fort Worth?

Yes, we respond to gate access emergencies in Fort Worth every day, including nights and weekends. If your gate won’t open and you’re blocked in or locked out, call (877) 610-2993 and a live person picks up. We’ll get someone moving toward your property as soon as we know what’s happening.

What warranty do you offer on access control work in Fort Worth?

Every access control job in Fort Worth carries our 90-Day Done Right Promise in writing. If the keypad, reader, or phone entry module we installed or repaired fails within 90 days, one call brings Hal back to fix it at no charge. No pro-rating, no conditions. Call (877) 610-2993 to schedule a free estimate.

Gate Parts & Welding in Fort Worth

Gate hinge replacement and on-site welding in Fort Worth typically runs $150 to $450 for most jobs, with custom fabrication higher because of the materials and time involved. We bring the welding rig and replacement parts to your driveway, and your gate stays where it hangs. More detail lives on our Gate Parts & Welding page.

Hinge Replacement

Most Fort Worth driveway gates hang on barrel hinges or strap hinges welded to the post and the frame. After years of opening and closing with posts slowly leaning in the clay, those hinge pins oval out the hinge leaves and the gate starts dragging. We cut the old hinge off, weld on a new one, and set the gate level. Typical hinge replacement in Fort Worth runs $150 to $300, depending on whether it’s a light pedestrian gate off a bungalow in Fairmount or a heavy ornamental iron driveway gate.

Post Replacement

Fort Worth sits on Blackland Prairie clay that swells every wet spring and contracts hard during summer drought. Gate posts set in concrete still move. We see posts leaned six degrees out of plumb in Ryan Place, Monticello, and Berkeley Place, where iron driveway gates went in 40 or 50 years ago and nobody’s touched the posts since. Post replacement runs $400 to $900, including digging out the old footing, setting a new steel post deeper with more concrete mass, and re-hanging your existing gate.

Custom Welding

Sometimes you don’t need a repair; you need a modification. We weld on extension bars where a driveway’s been widened, fabricate new operator mounting plates for slide gates, add decorative scrollwork to match an existing pattern, or build a custom steel frame for an automatic gate in a new Fort Worth subdivision. Custom welding ranges $200 to $1,200 depending on the design and material, and we quote it before striking an arc.

Do you weld on site, or do you take the gate to a shop?

We weld on site. Your gate stays in your driveway where it hangs, and we bring the welder, grinder, post jacks, and replacement parts to you. This saves you a week of no gate and avoids the damage that happens when a 400-pound iron gate gets strapped to a trailer. On-site welding is the only way to verify the gate swings true when the weld cools.

What’s your warranty on welding work in Fort Worth?

Every job carries the 90-Day Done Right Promise in writing. If a weld cracks, a hinge binds, or a post shifts within 90 days, one call brings Hal back to make it right at no charge. That’s the guarantee stated plainly. Not “up to” and not “in most cases.”

Brands We Service in Fort Worth

We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule operators. We stock common Linear, Viking, and BFT parts locally so you’re not waiting on a distributor two states away. See our brands for the full list.

Pricing for Gate Repair in Fort Worth, TX

Neighborhoods We Serve in Fort Worth

We work all over Fort Worth, but our trucks spend the most time in the older neighborhoods where iron gates and clay-shifted posts are a constant. Typical response inside Fort Worth is same-day for emergency repairs and within one business day for everything else.

• Arlington Heights (76107)
• Ryan Place (76110)
• Fairmount (76104/76110)
• Western Hills (76108)
• Monticello (76107)

Service Area - Cities Near Fort Worth

We’re based in the Dallas-Fort Worth metro and serve Fort Worth, TX along with the surrounding communities. If you’re in River Oaks, TX, Forest Hill, TX, Haltom City, TX, Benbrook, TX, or White Settlement, TX, we’ll come to you. No trip charge inside the county.

FAQs About Gate Repair in Fort Worth