Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Evergreen
A new driveway gate in Evergreen typically runs $3,800 to $14,000 installed, depending on the gate type, automation, and how much site work your slope demands. We’re Gatewood Fence & Gate, and we’ve been building and repairing gates in this foothill corridor long enough to know what the elevation and the wildlife do to them. Most Evergreen installs take two to four days once materials land, and every job starts with a written price you agree to before we touch anything. Call (877) 610-2993 and a live person answers, day or night.
Hal Gatewood’s name is on the shop and on every invoice. If you’re off Upper Bear Creek Road or down toward Marshdale, you’ll see us around. We’re not a call center three states away. We’re the outfit that welds on site, stands behind the job for 90 days in writing, and actually shows up when we say we will.
Why Gatewood Fence & Gate Is Evergreen’s Preferred Gate Installation Company
We’ve built a reputation in Evergreen the slow way: doing the job right and answering the phone afterward. Homeowners in the 80437 and 80439 zip codes call us because the person who quotes the job is the same person who welds the hinges and sets the posts. That’s Hal, or one of his crew who has been with him for years. No faceless dispatch queue. No voicemail at 2 a.m. when your gate is stuck open and the bears are already interested.
Our Gate Installation work around Evergreen tends to be concentrated in the higher, sloped lots off Bear Creek Road, Kerr Gulch, and down through the Witter Gulch corridor. We know those driveways. We know how the grade affects swing geometry and what the spring melt does to a footing poured in September. That local knowledge changes how we bid and how we build. Frankly, it’s the difference between a gate that opens smoothly for a decade and one that’s binding by March.
Evergreen is also where we see the highest black bear pressure on the Front Range. A gate installed with standard residential hardware gets bent within a season. We engineer for that reality, not for the showroom photo. That’s why we’re the call when a national outfit’s install fails its first winter up here.
Our Gate Installation Services in Evergreen
Driveway Gate Installation
Most Evergreen homes sit on long private drives, and the dominant gate type is a driveway entry gate, usually swing or slide, often automated. We install them on slopes that would make a flatland crew nervous. These are heavy gates, and at 7,000 feet they need deeper footings, stouter hinge posts, and anti-sag bracing that accounts for intense freeze-thaw cycling. A driveway gate here isn’t a weekend project. It’s a structural install.
Swing Gate Installation
Swing gates are the most common choice in Evergreen’s custom-home neighborhoods, and they’re the type that suffers most from post heave. When the ground freezes and thaws all winter, a footing can lift three inches and throw the whole gate out of plumb. We pour reinforced footings below the frost line, correct hinge geometry for slope, and set the gate so it still holds true after a decade of mountain winters. The difference is in the depth and the bracing, and that’s where we spend the time.
Sliding Gate Installation
On tighter Evergreen lots where the driveway runs steep or curved, a sliding gate often makes more sense than a swing. These need a solid track or cantilever base that tolerates gravel and snowmelt without binding. We install sliding gates with the same care on the footing as a swing gate, because a slid gate on a heaving base is just an expensive headache. Our crew also handles the heavier ornamental steel sliders that fit the look of Bear Creek and Evergreen Meadows homes.
Pedestrian Gate Installation
Alongside driveway gates, we build pedestrian gates for paths and side entries around Evergreen properties. These get used in rough conditions, wet snow, hard UV, and the occasional bear leaning on them to test the latch. We build them with the same reinforced frames and bear-resistant latching we put on the big gates, because the side gate is where wildlife usually finds the weak point. It’s the gate you forget to check, and it’s the one that fails first.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Evergreen
We install and service FAAC, BFT, and Viking operators, along with a handful of other proven brands. For Evergreen homeowners, we keep common parts on hand locally rather than ordering every bearing and limit switch from a warehouse a week out. Viking underground operators are a frequent choice for the custom ornamental gates around Upper Bear Creek, where nothing sticking up above grade is acceptable. FAAC and BFT linear operators cover most of the rest. When we install automation, we match the operator to the gate weight and the site’s snow load, not just whatever’s on the truck.
Common Gate Installation Problems We See in Evergreen Homes
- Post footing heave. At 7,000 feet, the freeze-thaw cycle is severe. Footings poured too shallow lift several inches over one winter, and a gate that closed perfectly in October won’t latch by February. We dig below the frost line and reinforce the concrete as standard practice, not as a line item upgrade.
- Bear damage to frames and latches. Evergreen’s bear density is among the highest on the Front Range. A standard spring latch gives way like it isn’t there, and black bears bend bottom rails and spring hinges if the gate doesn’t open. We build reinforced frames and bear-resistant latching from day one on every install in the 80437 and 80439 areas.
- Heavy wet snow load. Annual snowfall here often tops 100 inches, and it’s the wet kind that packs. A wood swing gate soaks it up, then collapses under the weight. We size steel frames and operator torque for that reality. Solar openers that work fine in Golden often fail up here because short winter days and snow-covered panels kill the battery.
- Solar operator failure in winter months. We regularly get calls in January from Evergreen homeowners whose solar gate opener died. The panel gets buried in snow, the battery drains, and the gate stays shut. On installs where solar is the only practical power, we size the panel and battery for elevation, not for Denver conditions. If line voltage can be pulled, we recommend it.
Pricing for Gate Installation in Evergreen, CO
Here’s real numbers for the Evergreen market, not a Denver price sheet. A basic single swing gate with manual latch starts around $3,800. A double swing driveway gate with automation typically runs $6,500 to $10,500. Custom ornamental steel gates, especially the heavier designs around Upper Bear Creek and Kerr Gulch, land between $9,000 and $14,000 installed with operators. Sliding gates sit in a similar range, $5,500 to $11,000, depending on steel weight and track work. Pedestrian gates run $900 to $2,800.
What moves the price in Evergreen is the footing work. Deeper pours, reinforced cages, and slope correction add labor that a flat Denver lot never requires. We quote that work upfront, in writing, and the price is firm. You’ll never get a different number when the crew shows up. Call (877) 610-2993 for a free estimate, and remember seniors and veterans get a permanent 10% discount.
We Also Serve Cities Near Evergreen
Our Evergreen service area also covers the nearby communities of Ken Caryl, Golden, Columbine, and Applewood. Same crew, same standards, same written price before we start. If you’re just over the county line or down the hill, we’ll still be the ones answering the phone.
Serving Evergreen, CO - Our Local Coverage Area
We’re based in the Evergreen area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Evergreen
In Evergreen, gate post footings should go at least 36 to 40 inches deep, below the frost line for this elevation. We reinforce the concrete with rebar and often bell the bottom of the hole to lock the footing into the soil. Shallow footings, the 24-inch kind that work fine in Denver, heave out of plumb within one winter up here. Call (877) 610-2993 if you want your footing verified before a gate goes on it.
Yes, and it happens more often than people expect. A standard spring latch gives way when a bear pushes on the gate, and the force is enough to bend bottom rails and spring hinges. In Evergreen, a gate secured only with a standard latch is effectively no gate once a bear decides the garbage is worth investigating. We build bear-resistant latching and reinforced frames into every install, because the alternative is replacing the gate after the first season.
Most solar gate openers struggle through Evergreen winters. The panel gets buried in snow, the short days limit charging, and the heavy wet snow load adds resistance the motor has to fight. Some work if we oversize the panel and battery, but line voltage is the more reliable path when it’s available. We’ll tell you straight what your site can support before we order anything. Call (877) 610-2993 for a free assessment.
On steep Evergreen grades, a swing gate often wins because it doesn’t need a long track that can fill with gravel and ice. But if the slope runs side-to-side, a slide gate with a cantilever design can work better. The real answer depends on the driveway’s specific geometry, and we’ll evaluate that in person before recommending anything. The right gate on a bad footing is still a failure in two winters.
We size the steel frame and the operator torque for snow load, not for dry summer conditions. Ornamental gates can look elegant and still carry a reinforced internal frame that holds against packed snow. We also set the gate’s rest position and limit stops so snow doesn’t build up behind the leaf and stress the hinges mid-winter. The fix is in the engineering, not in shoveling faster. Call (877) 610-2993 for a quote on a gate built to take an Evergreen winter.
Engineering a Gate for Evergreen’s Conditions
Here’s the part a generic gate installation page never tells you. A new gate in Evergreen has to survive three things working against it at once: freeze-thaw post heave, heavy wet snow, and black bears. That combination doesn’t exist down in the Denver flatlands. If you install a gate here the way you would in Lakewood, you’ll be replacing it before spring. We deepen the footings, reinforce the frames, and spec the latching for wildlife pressure. It’s not a premium add-on. It’s the baseline for a gate that still opens smoothly in its fifth winter.
On a sloped lot off Upper Bear Creek Road, we set a custom ornamental steel swing gate with a Viking underground operator after removing a collapsed cedar gate whose post footing had heaved a full three inches over one winter. Our crew poured a new reinforced footing, corrected the hinge post geometry, and added a safety photocell and keypad entry, then ran the gate through 50 cycles of freeze-thaw simulation before the first heavy snow arrived. That’s the standard, because up here, the mountain will find every shortcut you took.
If you’re in Evergreen and you want a gate installed once, call (877) 610-2993. Hal’s name is on the shop, the shop is down the road, and the price is written down before we start. That’s the oldest accountability there is.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Evergreen and the surrounding foothill communities.