Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Commerce City
Gate installation in Commerce City runs $1,800 to $7,500 for most residential jobs, with driveway swing gates on the lower end and ornamental steel slide gates with automation on the higher end. We serve the whole 80022 and 80037 area, and a live person answers our phone at (877) 610-2993 day or night. Hal Gatewood has been installing and repairing gates since 2001, and the name on the shop is the name you’ll see on the invoice. If you’re east of the South Platte or up in Reunion, we know what your gate is up against because we’ve worked on hundreds of them here.
Key Takeaways
- Most residential Gate Installation work in Commerce City costs between $1,800 and $7,500, quoted and agreed before we start.
- West- and south-facing gates near the Suncor corridor rust two to three times faster than gates a few miles away, so we default to hot-dip galvanized hardware on every install.
- Older ranch homes in central and southern Commerce City often have undersized post footings that freeze-thaw cycles wreck over time.
- We install and service FAAC, BFT, Linear, and Viking operators, plus brands like LiftMaster and DoorKing.
- Every install carries the 90-Day Done Right Promise in writing.
Why Gatewood Fence & Gate Is Commerce City’s Preferred Gate Installation Company
We’ve been out here long enough to know which gates fail early and why. Commerce City isn’t Aurora and it isn’t Denver. The air along the South Platte industrial corridor carries sulfur compounds and particulates that eat through cheap powder coat in a couple of winters. Gates installed with standard zinc hardware near the refinery corridor show deep pitting in two to three years. We stopped using that hardware years ago on anything west-facing. Hot-dip galvanized posts, hinges, and rollers are the default here, not an upsell. That single decision saves Commerce City homeowners a full hardware replacement down the road.
Our customers in Commerce City call us for two reasons. First, a live person answers the phone every time, around the clock, not a voicemail tree or a call center three states away. Second, when we quote a price, that’s the price. We don’t show up and “find” an extra eight hundred dollars of necessary work. Hal Gatewood has been running this shop since 2001 and his published address means you can drive to the shop and look him in the eye if something isn’t right. That accountability is the oldest kind there is.
Our Gate Installation Services in Commerce City
Driveway Gate Installation
A driveway gate in Commerce City has to handle wind, ice, and industrial grit, so we build for all three. Most single driveway swing gates in the 80022 and 80037 ZIP codes run $1,800 to $4,200 depending on width, material, and whether you want an opener. We set posts deeper than code minimums because the freeze-thaw out here will heave a shallow footing in three seasons. Every driveway gate gets hot-dip galvanized hinge posts and stainless hardware as a matter of course.
Pedestrian Gate Installation
Walk gates near the older ranch homes in south and central Commerce City often sit beside a driveway gate and share a post. We pour and set that shared post correctly the first time, so a sagging walk gate doesn’t pull the drive gate out of alignment a few years later. Pedestrian gate installs typically run $700 to $1,800 in Commerce City. You can keep the existing post if it’s still sound, but a lot of posts from the 1960s and 1970s aren’t, and we’ll tell you straight before we quote anything.
Sliding Gate Installation
Sliding gates out here live hard. Airborne grit from the industrial corridor works into rollers, tracks, and rack-and-pinion gears, and the downslope winds off the high plains add lateral force that wears parts faster than in sheltered neighborhoods closer to the foothills. A new residential slide gate in Commerce City typically runs $3,500 to $7,500 installed. We run cantilever or track systems depending on the grade, and that’s a decision we make on-site, not from a photo. We also stock common replacement rollers and racks locally so we don’t leave you waiting on a freight shipment.
Swing Gate Installation
Most older Commerce City properties with gates have tubular steel swing gates, and many of them were hung before UL 325 entrapment protection existed. We recently replaced a sagging swing gate on a 1960s ranch in the older southern neighborhoods where the original hinge post footing had rotted below grade. Rather than just resetting the post, we poured a deeper concrete footing, swapped in hot-dip galvanized hinge posts, and upgraded to a LiftMaster operator with safety photocells. The old gate had been hung decades before modern safety requirements existed. That’s the difference between a panel swap and an install done right.
For dual leaf double gates in Commerce City, we size operators correctly and set both posts in concrete to match grade, because a mismatched double gate binds and burns out motors. We’ll tell you if your existing posts can be reused or if they need to come out.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Commerce City
We install and service FAAC, BFT, Linear, and Viking operators across Commerce City, along with LiftMaster, DoorKing, Ghost Controls, Elite, and Mighty Mule. We stock common control boards, safety edges, and remotes locally, so most repairs don’t wait on a truck from out of state. If you have an older operator and need to know whether it’s worth retrofitting, we’ll give you a straight answer. Some boards can be replaced affordably. Some operators aren’t worth spending money on, and we’ll say so.
Common Gate Installation Problems We See in Commerce City Homes
- Premature rust from refinery and industrial airborne particulates. Gates on west- and south-facing lot lines east of the South Platte industrial corridor often show deep pitting within two to three years of installation. Standard zinc hardware simply doesn’t hold up here. We default to hot-dip galvanized steel and powder-coat touch-ups at every install.
- Hinge post footings cracked by freeze-thaw cycling. Ranch homes built in the 1950s through the 1970s in central and southern Commerce City often have shallow post footings. Repeated freezing and thawing heaves the post and the gate starts sagging. A panel-only fix will fail again in a season or two, because a gate sags in the hinge post, not in the middle.
- Slide gate roller and track wear from airborne grit. Fine particulates from the industrial corridor and open-plains wind work into tracks and rollers, accelerating wear and causing binding. We clean and adjust slide tracks seasonally for Commerce City customers who want their gates to keep running without unexpected breakdowns.
- Older operators without modern safety entrapment protection. Many legacy gates in Commerce City were installed before UL 325 required safety photocells and reversing edges. If you have kids, grandkids, or delivery drivers walking near the gate, that’s worth addressing. We retrofit older gates with current safety edges and photocells without replacing the whole operator in most cases.
Pricing for Gate Installation in Commerce City, CO
A single driveway swing gate in Commerce City typically runs $1,800 to $4,200 installed. A quality pedestrian gate runs $700 to $1,800. A residential sliding gate with automation runs $3,500 to $7,500 depending on length, material, and whether we’re pulling old posts or setting new ones. Security gates with heavier steel, welded frames, and access control push toward the upper end and sometimes higher for long ornamental runs in the newer Reunion subdivisions.
What moves the number: post replacement versus reuse, operator type, gate length, and whether you need access control or a keypad added. We quote the price before any work starts. You know the cost before we touch a tool. Call (877) 610-2993 for a free estimate, and if you’re a senior or veteran, there’s a standing 10% discount on every job.
We Also Serve Cities Near Commerce City
Our Gate Installation in Commerce City work keeps us in the surrounding communities every week. We regularly install and repair gates in Derby, Federal Heights, Sherrelwood, and Welby, and the same crew and the same written guarantee follow us to each one.
Serving Commerce City, CO - Our Local Coverage Area
We’re based in the Commerce City area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Commerce City
With standard zinc hardware, expect visible rust and pitting within two to three years on west- and south-facing gates east of the South Platte industrial corridor. With hot-dip galvanized posts and stainless hardware installed correctly, we expect 15 to 20 years of service before any post work is needed. The single biggest cost difference over time is the hardware choice, not labor. Call (877) 610-2993 for an exact quote on your gate, free.
Yes, in most cases we can retrofit a 1970s slide gate with current safety photocells and reversing edges without replacing the entire gate or operator. We match the older track and rack system with a modern controller and safety loop. If the gate frame itself is rusted through or the track is too worn, replacement may be cheaper than repeated repairs, and we’ll show you the numbers side by side before you decide.
Often yes. Reunion homes tend to have ornamental iron driveway gates and some HOA-managed community entry gates that need heavier duty operators and access control panels built for frequent cycling. The older working-class neighborhoods around central and southern Commerce City more often have tubular steel gates where the priority is corrosion resistance and post integrity. We install both types and we’ll pick hardware based on the actual location, not a generic package.
For a swing gate in Commerce City, we set posts at least 36 inches deep with a wider footing than code minimum, because the open high plains allow deeper, more aggressive freeze-thaw cycling than in Denver’s more built-up core. A shallow 24-inch footing is a future sag. We also pay attention to the hinge side, because that post carries the entire gate load and the wind leverage.
Airborne grit from the South Platte industrial corridor plus frequent downslope winds from the open plains work fine particulates into the rollers and tracks. That grit acts like sandpaper every time the gate cycles, and the unshielded exposure means rollers and rack-and-pinion mechanisms bind and wear faster than in Denver’s more sheltered neighborhoods. We schedule seasonal track and roller adjustments for Commerce City customers who want to stay ahead of a breakdown. Call (877) 610-2993 and we’ll get you on the schedule.
Call Gatewood Fence & Gate for Gate Installation in Commerce City
If your gate is sagging, rusting, or overdue for replacement, call us at (877) 610-2993. A live person answers, we’ll schedule a time that works for you, and we’ll give you a written price before any work begins. Free estimates, no trip charge inside the county, and the 90-Day Done Right Promise on every install. Hal Gatewood’s name is on the shop and on every invoice.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Commerce City and the surrounding Front Range since 2001.