Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Beverly Hills
Gate installation in Beverly Hills is a different animal than most of Los Angeles. North of Sunset, you’re dealing with graded driveways, long runs, and gates wide enough to swallow two cars at once. South of Santa Monica, the lots are tighter but the architecture demands a lighter touch. A gate that drags on a hillside, or an operator that can’t move a 400-pound steel panel, isn’t a gate problem. It’s a design problem. We fix both. If you’re looking for a gate that clears the apron every cycle and an operator sized for the actual load, explore our Gate Repair - Beverly Hills services or call us at (877) 610-2993. Hal Gatewood has been building and installing gates since 2001, and the gate you see in the catalog is not always the gate your driveway needs.
Key Takeaways
- Beverly Hills hillside estates need grade-compensating hardware, not flat-lot components.
- A typical driveway gate installation in Beverly Hills runs $4,500 to $18,000 depending on panel size, operator type, and slope.
- Marine-layer moisture rusts iron gates year-round here, even without rain. Material selection matters.
- We stock and service Linear, Viking, Ghost Controls, and DoorKing operators for Beverly Hills homes.
- Every job carries the 90-Day Done Right Promise in writing. No fine print, no runaround.
Why Gatewood Fence & Gate Is Beverly Hills’s Preferred Gate Installation Company
Our Gate Installation team has walked more Beverly Hills driveways than we can count, and the story is usually the same. Somebody installed a gate that looked right in a photo and was wrong for the site. A post set too shallow on a graded lot. An operator rated for a suburban single swing asked to push an estate double gate. We’ve been owner-operated since 2001, and Hal Gatewood’s name is on the shop and on every invoice. That means when something isn’t right, the person who shows up to make it right is the same person you talked to on the phone.
We serve all of Beverly Hills from the flats south of Santa Monica Boulevard to the hills above Sunset. The 90210 zip code has some of the most demanding gate installations in Southern California: long driveways on grade, oversized panels, and homeowners who expect the gate to work without thinking about it. We answer calls around the clock with a live person, not a voicemail queue. When you call about a gate that’s dragging on a hillside, you’ll talk to someone who knows what a grade-compensating hinge is and why it matters.
Our Gate Installation Services in Beverly Hills
Driveway Gate
Driveway gates in Beverly Hills fall into two camps. South of Santa Monica Boulevard, we’re installing single swing or sliding gates on Spanish Colonial and mid-century lots where curb appeal matters as much as function. North of Sunset, we’re building for span and slope. A 16-foot double gate on a grade needs articulated hinges or a ram-style operator, not the same hardware you’d put on a flat West Hollywood pad. We size the post footings for the slope, not just the panel weight.
Pedestrian Gate
Pedestrian gates in Beverly Hills are often the forgotten entry, but on estate properties they’re the gate that gets used ten times a day. We install and match pedestrian gates to the existing driveway gate, including decorative ironwork that matches the original 1920s or 1930s patterns you see in the hills above Sunset. If the gate is automated, we wire it into the same Beverly Hills Gate Access Control system so one code or intercom works for both.
Sliding Gate
Where driveway width is tight, a sliding gate is the right call. Beverly Hills flats south of Santa Monica, especially around the 90211 and 90212 zips, don’t always have the swing clearance for a double gate. We run cantilever and track-style sliders with operators sized for the panel, and we pay attention to track debris. Santa Ana winds push grit and leaves into roller tracks, and a track that’s not set clean will eat rollers and wear the operator gear assembly faster than anything else.
Swing Gate
Swing gates are the most common install in Beverly Hills, and the most commonly misinstalled. On a flat lot, a swing gate is forgiving. On a hillside north of Sunset, a post that settles half an inch throws off the slope clearance and the gate drags. We pour deeper footings, use grade-compensating hinges where the grade calls for it, and set the operator limits with the gate loaded, not on a bench. The gate clears the apron on every cycle because we built it to.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Beverly Hills
We’re certified to service and install operators from Linear, Viking, Ghost Controls, and DoorKing, and we keep common Gate Parts & Welding in Beverly Hills on the truck when we know we’re heading to a local job. That means less waiting on a part to ship while a gate sits dead across a driveway. For estate properties with heavier panels, we often spec Linear or DoorKing units for their torque ratings. For solar or long-run applications, Ghost Controls and Viking get the call. The right brand depends on the site, not on a brochure.
Local Conditions That Shape Gate Installation in Beverly Hills
Beverly Hills sits five to six miles from the Pacific, and that proximity does something people underestimate. Daily marine-layer moisture cycles accelerate oxidation on iron gates year-round, even when the city’s rainfall numbers look low. Surface rust on hinges, operator brackets, and decorative ironwork is a chronic complaint here, not a seasonal one. We see gate hardware fail more from rust than from wear on some of the older estate gates above Sunset. That’s why we push stainless or sealed hardware on installs within a couple miles of the marine layer, and why we treat raw steel before it goes up. The same gate installed identically in Culver City and in Beverly Hills will age differently. Our material choices reflect that.
One more thing that makes Gate Installation in Beverly Hills different: this city has one of the highest concentrations of custom-fabricated estate gates in the country. Ornate wrought-iron panels, dual-lane entries, multi-camera access control, video intercoms. Nearly every gate north of Sunset is a one-of-a-kind architectural piece, not an off-the-shelf component. When a hinge post shifts on one of those, you don’t swap in a replacement from a catalog. You fabricate the fix on site, which is exactly what we do. On several hillside estates we’ve worked with estate managers and private security firms rather than the homeowners themselves. That changes the job. The gate has to work with the existing access control platform, whether that’s a phone-based intercom or a guardhouse loop system, and it has to be done without leaving a driveway blocked for two weeks.
Common Gate Installation Problems We See in Beverly Hills Homes
- Hinge posts settling on graded driveways. A hillside lot north of Sunset puts lateral pressure on footings from day one. When a post settles, the swing gate drags and the operator trips its limit switch. It’s often misdiagnosed as a bad motor. It’s almost always a post that was never poured deep enough for the slope.
- Marine-layer rust on iron hardware. Daily coastal moisture keeps rust active on hinges and brackets year-round. We see seized hinge pins and sagging panels that stress the operator into premature failure. Hardware selection here isn’t optional.
- Undersized operators on wide double gates. Estate driveways in Beverly Hills often need a 16-foot double gate with steel panels that weigh hundreds of pounds. Pair that with a residential-grade operator and the gear assembly fails early. Torque ratings matter more than brand names.
- Debris in tracks and gear assemblies after Santa Ana events. Wind-driven grit gets into roller tracks and operator drives. On gates that aren’t serviced regularly, that grit accelerates wear fast. We set installation so that service points are accessible and track channels drain correctly.
A Hillside Install We Won’t Forget
Up a long, graded driveway in the hills north of Sunset, our crew installed a double swing gate with a FAAC ram-style operator on a pair of custom steel panels. The original hinged posts had shifted on the slope, so we poured new post footings with deeper embedment and set articulated hinges to compensate for the grade, then wired the operator with safety photocells and a loop detector at the entry. The gate now clears the apron on every cycle, even when the Santa Anas push debris against the rack and pinion. That job had been diagnosed twice before as a motor failure. It was never the motor.
Pricing for Gate Installation in Beverly Hills, CA
A single driveway swing gate in Beverly Hills typically runs $4,500 to $8,500 installed, including post footings, hinges, and operator. A pedestrian gate runs $1,800 to $3,200. A double gate on a graded hillside lot with custom panels and a heavy-duty operator runs $9,000 to $18,000, and more for dual-lane configurations or elaborate ironwork. The spread is real: panel weight, slope, operator torque, and access control integration all move the number. What doesn’t move is the price after we quote it. You’ll get a written estimate before any work starts, and the price on that estimate is the price on the invoice. We also offer a free second opinion on any written estimate from another company, and a permanent 10% discount for seniors and veterans. Call (877) 610-2993 and we’ll come measure the driveway and give you a written quote. No trip charge inside the county.
We Also Serve Cities Near Beverly Hills
If your property sits just outside the Beverly Hills line, we work those streets too. Century City, West Hollywood, Culver City, and Hollywood are all within our regular service range. The hillside issues change as you move across the county line, but the standard of work doesn’t.
Serving Beverly Hills, CA - Our Local Coverage Area
We’re based in the Beverly Hills area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Beverly Hills
A wide double gate on a grade needs a heavy-duty operator with enough torque for the panel weight plus the slope, typically a ram-style actuator or a high-torque linear arm. We spec units like the FAAC ram-style or equivalent Linear and DoorKing models, and we set grade-compensating hinges so the gate never drags the apron. The operator alone isn’t the fix; the hinge geometry has to match the slope. Call (877) 610-2993 and we’ll walk the driveway with you and tell you exactly what it needs.
Yes, but only if the panel is sized right and the battery bank is matched to the operator’s draw. Heavy iron gates need more current to move, and a long Beverly Hills driveway with shade from mature landscaping reduces solar input. We run the numbers on panel wattage, battery capacity, and cycle count before recommending solar. If solar can’t keep up with a 600-pound iron gate, we’ll say so and run the power instead. Get the exact quote by calling (877) 610-2993.
We prevent sagging by pouring post footings deep enough for the slope and soil, and by using articulated or grade-compensating hinges where the driveway runs on a meaningful grade. A gate sags in the hinge post, not in the middle, and the post is where we start. On hillside lots north of Sunset, we also account for lateral soil pressure and drainage so the post doesn’t shift five years in. Estimates are free, and the price is locked before work begins.
Long estate driveways often need loop detectors with extended lead-in wire and sensitivity set for the gate’s distance from the detection point. Beverly Hills properties with private security or dual-lane entries regularly use loop detectors tied into the access control system so the gate opens for exiting vehicles without a remote. We install and calibrate loop detectors on every automated gate install where vehicle detection is needed. For a site-specific recommendation, call (877) 610-2993.
Automatic gates in Beverly Hills must meet UL 325 entrapment standards, which means safety photocells, contact edges, or both depending on the gate’s travel path and operator type. We install photocells and edge sensors as standard on every automated gate, and we test the reversal force with an actual obstruction before the job is done. This is a genuine safety issue, and a gate that can crush a car can do worse to a person. Call (877) 610-2993 for a free estimate that includes all required safety equipment.
Contact Gatewood Fence & Gate
If you’re ready to talk about a gate that fits your Beverly Hills driveway, not someone else’s, call (877) 610-2993. A live person answers, day or night. We’ll come out, measure the site, and give you a written estimate that doesn’t change when the job starts. Hal Gatewood has been doing this since 2001, and the 90-Day Done Right Promise is stamped in writing on every job, including yours.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Beverly Hills since 2001.