Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Atlanta, GA
Gate repair in Atlanta comes down to two forces that never let up: red Georgia clay that heaves posts out of plumb, and a dense tree canopy that drops limbs on gate arms every summer thunderstorm. We fix both, and we do it with a live person on the phone around the clock. Whether your swing gate is dragging in Inman Park or a storm dropped a limb across your Buckhead driveway, call (877) 610-2993 and you’ll reach Hal or someone from his crew, not a voicemail.
Why Atlanta Homes Are Different
Atlanta’s red clay soil expands when wet and contracts when dry. That cycle pushes gate posts up, tilts them sideways, and throws hinges out of alignment every single season. We see gates in Grant Park and Inman Park that were bolted onto original brick columns from the early 1900s, columns built to hold a fence, not a 400-pound motorized gate. The column stays put while the clay underneath heaves, and the gate binds. It’s a structural problem, not a mechanical one, and it recurs every spring unless the post is reset with a proper footing that gets past the clay.
Then there are the storms. Atlanta is one of the most tree-canopied major cities in the United States, and summer thunderstorms drop limbs fast. A limb hitting a gate arm bends the frame, breaks the bracket, or tears the motor mount. We replace a lot of pickets and straighten a lot of frames after those storms. And in Buckhead, specifically, so many high-end automated driveway gates went in during a tight window from roughly 1997 to 2007 that the neighborhood is now seeing a near-simultaneous wave of failing control boards and burned-out swing-gate motors. That’s not a coincidence. It’s age, concentrated.
Gate Repair in Atlanta
Gate repair in Atlanta typically runs $200 to $800 depending on whether we’re replacing a hinge, rewiring a control board, or welding a cracked frame. The most common calls we get are gates that won’t open, gates that sag on their hinges, and gates that got clipped by a falling limb during the previous night’s thunderstorm. We answer the phone with a live person around the clock, and we’ll tell you straight what’s wrong, what it costs, and whether it’s worth fixing. Our Gate Repair work starts with the post and the hinge, not the motor, because in this city that’s usually where the problem lives.
Electric Gate Repair
Electric gate systems in Atlanta fail most often at the control board, the capacitor, or the safety sensors, and the moisture from 50 inches of annual rainfall accelerates every one of those failures. We work on nine major brands including Viking and DoorKing, and we stock common boards and sensors locally so Atlanta customers aren’t waiting on a part from across the country. Electric gate board replacement lands between $350 and $600 depending on the brand and board.
Automatic Gate Repair
Automatic gates in Atlanta’s older neighborhoods like Inman Park and Grant Park often have a deeper problem: the gate was retrofitted onto original brick or stacked-stone columns that were never engineered for motorized loads. The motor burns out early because it’s fighting a column that’s slowly shifting. We diagnose that before we replace the motor, because putting a new motor on a shifting column means you’ll pay for the same repair twice. Full motor replacement on a swing gate, especially on the larger Buckhead estates with Viking or Elite systems, runs $600 to $1,200.
Hinge & Post Repair
A gate sags in the hinge post, not in the middle. That’s where we start. Atlanta’s red clay soil expands when wet and contracts when dry, which heaves posts out of plumb across seasons, and a hinge that was perfectly level in April can be dragging by September. A hinge replacement or basic realignment typically runs $200 to $350. For posts that have shifted beyond shimming, we set new footings that extend well past the clay layer so the post stops moving, and we weld on site so the gate stays in your driveway instead of being hauled off to a shop.
Gate Realignment
Realignment in Atlanta is rarely a one-time fix unless the underlying cause is addressed, and the underlying cause is usually the soil or a struck gate arm from a falling limb. We’ll realign the gate, check every hinge and the post footing, and tell you honestly whether we’re correcting a one-time impact or a seasonal problem that needs a deeper fix. Weld and rust repair on a wrought-iron gate usually falls between $250 and $500 per section, depending on how far the rust has eaten into the steel.
How fast can you get to my Atlanta home for a gate repair?
We typically reach most Atlanta neighborhoods within a few hours of your call, and emergency calls like a gate stuck open, a gate that won’t close, or a fallen limb blocking your driveway get prioritized. Phone (877) 610-2993 and you’ll get a live person, not a voicemail.
Do you cover all of Atlanta, including Buckhead, Inman Park, and Grant Park?
Yes. We repair gates throughout Atlanta, including ZIP codes 30305, 30306, 30307, and 30308. Hal’s crew is familiar with the specific gate setups in Buckhead’s large-lot estates, the retrofitted gates on historic columns in Inman Park, and everything in between. Call (877) 610-2993 and we’ll quote it over the phone.
Gate Installation in Atlanta
Gate installation in Atlanta runs $1,200 to $9,500 depending on the gate type, size, and whether you’re automating it. A basic steel pedestrian gate starts around $1,200, while a custom ornamental driveway gate with operator and intercom runs $6,000 to $9,500. We show up in the window we give you, and we set every post in concrete footings that extend below Atlanta’s red clay layer so the gate doesn’t start sagging within two seasons. For a full Gate Installation, we start with a free measure and a written price before anything is ordered or built.
Swing Gate
Swing gates are the most common style on Atlanta’s older estates, especially in Buckhead and along West Paces Ferry. They hang from hinge posts that take enormous load, and in Atlanta’s red clay those posts are the first thing to move. A typical residential swing gate installation in Atlanta runs $2,800 to $7,500, depending on width, ornamentation, and whether you’re automating it. We set footings below the clay line and weld hinges on site so the gate hangs true from day one.
Driveway Gate
A driveway gate in Atlanta needs to handle three things: a vehicle, a storm season, and a soil that moves. We build and install driveway gates sized to your opening, with operators rated for the gate’s actual weight. Driveway gate installations in Atlanta typically run $3,500 to $9,500 with automation. Buckhead alone has a huge number of automated driveway gates from the 1997 to 2007 boom that are now dying at the motor, and we handle the full package: gate, posts, operator, safety photocells, and keypad entry.
Sliding Gate
Sliding gates make sense on Atlanta properties with a steep grade or limited swing clearance, which you see often in neighborhoods like Grant Park where lots are tighter and driveways slope toward the street. A sliding gate rides on a track or cantilever system that has to be set level and stay level. Sliding gate installations in Atlanta generally run $3,000 to $8,000. In clay soil, the track’s sub-base matters as much as the gate itself, and we’ll tell you honestly whether your site suits a slide or not.
How deep should gate post footings be in Atlanta’s red clay to prevent heave?
At least 36 inches, past the active swell zone of the red clay. Atlanta’s clay expands when wet and contracts when dry, and a footing that stops at 24 inches or shallower will move seasonally and tilt the post. We extend footings below the clay layer and, on heavy automated gates, add a concrete collar for extra bearing. Call (877) 610-2993 and we’ll tell you what your specific site needs.
Do my automatic gates need entrapment protection in Atlanta?
Yes. Any automated gate needs safety photocells or contact edges that reverse the gate if a person or vehicle is in the travel path. It’s a safety requirement, not an upsell, and we install it on every automated gate we build or retrofit, whether it’s a new security gate in Buckhead or a pedestrian gate in Inman Park.
Gate Motor & Opener in Atlanta
When a gate motor quits in Atlanta, the first question is usually whether it’s the motor, the board, or the gate itself. In most of the Atlanta ZIP codes we run, the answer is a mix: red clay moves posts out of plumb, and a motor fighting a tilted post burns out years early. We get to Atlanta gates fast, and we’ll give you a straight answer on the phone before anybody rolls a truck. Our Gate Motor & Opener work covers nine major brands, including Viking, DoorKing, and Elite.
Motor Installation
A new gate motor in Atlanta runs on two decisions: what’s right for the gate’s weight and what’s right for the soil underneath it. We measure the leaf, check the column or post, and test the ground before we recommend anything. A plain motor replacement on a standard residential swing gate in Atlanta typically runs $420 to $750, including the motor and labor. On Buckhead estates where swing arms went in during the 1997 to 2007 boom, a lot of what we’re installing now is a full drive-system replacement matched to the original ironwork.
Motor Repair
Most Atlanta gate motor failures we see are not actually the motor. It’s a dead capacitor, a stripped gear, a board that got fried by lightning during a summer thunderstorm, or a burned limit switch. If the control board is involved or it’s a slide system, you’re usually looking at $600 to $1,200. We troubleshoot the whole circuit before we quote a replacement, and if the motor can be saved, we tell you. If it can’t, we say so plainly and show you the failed part on the ground next to the post.
Slide Motor
Sliding gates on Atlanta’s commercial properties and some of the older estate lots see two recurring problems: caked clay and pine straw in the track, and bearings that seize from moisture. We clear the run, check the rack gear for wear, and set the travel limits correctly so the gate doesn’t slam the end stop a thousand times and shake the motor loose. A full drive-system replacement on a Buckhead estate with a heavy wrought-iron leaf runs $1,500 to $3,800, depending on the gate’s weight, the condition of the posts, and whether we’re matching an existing brand or converting to a more reliable one.
Can you repair my gate motor the same day in Atlanta?
Yes, in most parts of Atlanta the same day is very doable. For a standard motor repair in places like Druid Hills or the 30306 ZIP, the truck is usually at your place within a few hours. Call (877) 610-2993 and we’ll tell you honestly when we can be there.
Is emergency gate service available at night in Atlanta?
Yes. A live person answers around the clock, seven days a week, not a voicemail. If your gate fails open at night and you’re trying to keep a dog in or a driveway secured, call (877) 610-2993 and you’ll get Hal or the person on call.
Gate Access Control in Atlanta
Gate access control in Atlanta usually means one of two calls: the keypad stopped reading codes, or the gate stopped responding to the remote entirely. In our experience, it’s rarely the keypad or the remote itself. It’s water intrusion from 50 inches of annual rainfall, an ice storm that froze the membrane solid and split it, or a limb that knocked the receiver antenna out of alignment. For Gate Access Control in Atlanta, we test the wiring first, then the board, then quote you a written price.
Keypad Entry
A dead keypad in Atlanta is often not a dead keypad. It’s water intrusion finding a cracked seal, or an ice storm that froze the rubber membrane solid and split it. A straightforward keypad swap on a working system runs $225 to $395, including programming all existing codes. If the keypad is wired to an older board that can’t store enough codes, we’ll tell you before we touch anything.
Remote Control
When an Atlanta homeowner says the remote stopped working, the first thing we ask is whether the gate had a close call with a tree limb recently. Summer thunderstorms drop limbs on gate arms and knock the receiver antenna out of alignment more often than the remote itself fails. Reprogramming a remote or replacing a receiver module usually runs $150 to $300. We carry remotes for Linear, DoorKing, and Ghost Controls, so most Atlanta jobs are done same day without ordering parts.
Phone Entry
Phone entry lets you buzz the gate open from a call, which matters in Atlanta’s hillier neighborhoods where the gate is 150 feet from the front door down a slope. Retrofitting a phone entry module onto an existing gate operator typically runs $450 to $800 depending on whether the existing board can accept it. Older DoorKing and FAAC boards sometimes can’t. If that’s the case, we show you the board and explain the options without pushing a full replacement.
Why does my Atlanta gate keep coming out of plumb even after the hinges are adjusted?
Because the hinge post is moving, not the hinges. Atlanta’s red Georgia clay expands when it’s wet and contracts when it’s dry, which heaves the post upward and sideways across seasons. The real fix is resetting the post on a deeper footing that bypasses the clay layer. Call (877) 610-2993 for an exact quote, estimates are free.
How do Atlanta ice storms affect my gate keypad or card reader?
Ice storms in Atlanta freeze keypad rubber membranes solid, and when they freeze they split. Water gets inside, the circuit board shorts, and the keypad bricks during the one week you really need it. We get a spike in keypad and card reader calls every time Atlanta has an ice event.
Gate Parts & Welding in Atlanta
Gate parts and welding in Atlanta means dealing with two forces that never let up: red Georgia clay that shoves hinge posts out of plumb, and summer storms that drop limbs on top rails. We repair both, usually in the same visit. If your swing gate drags, your latch misses the post, or a weld cracked clean through, we fix it on site and back the work with a written 90-Day Done Right Promise. See our Gate Parts & Welding page for the full scope of what we fabricate and repair.
Hinge Replacement
Most Atlanta gate sag doesn’t start in the hinge. It starts in the post. The red clay under our feet expands when it’s wet and contracts when it’s dry, and every cycle nudges the hinge post a little further off plumb until the gate drops and drags. Hinge replacement on a standard residential swing gate typically runs $180 to $340. We replace hinges sized for the gate’s actual weight, not the weight the original installer guessed, and we check the post footing before we weld anything.
Post Replacement
Post replacement in Atlanta is where local knowledge actually changes the invoice. A gate post set in a shallow footing will fail here. We set new steel posts in concrete footings that extend well past the clay layer so the wet-dry cycles don’t keep working the post loose. A full post replacement with a new steel post set in a deep concrete footing usually lands between $450 and $900 depending on post size and whether we’re setting one post or both. This is the single most important thing we do for swing gates in this market.
Custom Welding
On Atlanta’s higher-end properties, a gate isn’t a commodity, and a sloppy weld on a custom ornamental gate is the kind of thing you’ll notice every time you pull into the driveway. Custom welding repair, like re-welding a torn top rail or a broken picket, generally runs $150 to $400. We weld on site, which means the gate stays in your driveway instead of getting hauled to a shop across town. That matters for heavy wrought-iron gates in Buckhead, Inman Park, and Grant Park where gates were retrofitted onto brick or stacked-stone columns that were never meant to swing under motorized control.
Why does my Atlanta swing gate keep sagging even after the hinges were replaced?
Because the problem is usually in the post footing, not the hinge itself. Atlanta’s red clay expands when wet and contracts when dry, and over a few seasons that cycle shoves a shallow-set hinge post off plumb. We check the post before we touch the hinges. Call (877) 610-2993 and we’ll tell you honestly what’s moving.
Can you keep my ornamental gate looking original while you weld and replace parts?
Yes. On custom ornamental gates in Atlanta, we match the weld to the original profile and finish the repair so it doesn’t read as a patch. The standard isn’t just that it holds. It’s that you can’t tell where the break was. If you want to keep the look original, that’s exactly how we work.
Brands We Service in Atlanta
We service nine major gate brands in Atlanta, including Viking, DoorKing, and Ghost Controls, with common boards, sensors, and remotes stocked locally so you’re not waiting on a part from across the country. That local stock means most repair jobs are finished same day. See our brands page for the full list.
Pricing for Gate Repair in Atlanta, GA
| Service | Typical Range in Atlanta |
|---|---|
| Hinge replacement or basic realignment | $200 – $350 |
| Electric gate board replacement | $350 – $600 |
| Full motor replacement (swing gate) | $600 – $1,200 |
| Weld and rust repair (per section) | $250 – $500 |
| Pedestrian gate installation | $1,200 – $2,800 |
| Driveway swing gate installation | $2,800 – $7,500 |
| Sliding driveway gate installation | $3,000 – $8,000 |
| Motor replacement, standard residential | $420 – $750 |
| Keypad replacement | $225 – $395 |
| Remote or receiver replacement | $150 – $300 |
| Hinge replacement (parts & welding) | $180 – $340 |
| Full post replacement with deep footing | $450 – $900 |
What pushes a price up in Atlanta is usually the soil, not the gate. A post that has heaved off plumb means deeper footings and more labor than a simple hinge swap. The price we quote before work starts is the price you pay, in writing, and there’s no trip charge inside the county.
Neighborhoods We Serve in Atlanta
We work all over Atlanta, from the historic streets of Inman Park and Grant Park to the wide lots of Buckhead and the tree-lined blocks of Virginia-Highland. Typical response time across the city is same-day or next-day for most repair calls, faster if it’s a gate stuck open or a limb blocking your driveway.
- Buckhead (30305)
- Virginia-Highland (30306)
- Inman Park (30307)
- Midtown (30308)
- Grant Park
Service Area - Cities Near Atlanta
Besides covering all of Atlanta, we regularly work in the surrounding communities. If your gate is down in Druid Hills, GA, North Decatur, GA, Gresham Park, GA, North Druid Hills, GA, or East Point, GA, the same crew and the same 90-Day Done Right Promise apply. Call (877) 610-2993 and we’ll tell you when we can be there.
Serving Atlanta, GA - Our Local Coverage Area
Gatewood Fence & Gate crews serve Atlanta and the communities around it; dispatch is coordinated from our Atlanta office. The map shows the Atlanta coverage area; if your address is on it, we can help.
Also serving nearby: Atlanta, GA, Druid Hills, GA, North Decatur, GA, Gresham Park, GA, North Druid Hills, GA, East Point, GA.
FAQs About Gate Repair in Atlanta
We typically reach most Atlanta neighborhoods within a few hours for a same-day call, and emergency situations like a gate stuck open or a fallen limb blocking a driveway get prioritized. Phone (877) 610-2993 and you’ll get a live person who can tell you honestly when the truck will arrive.
Many Atlanta neighborhoods, especially in Buckhead and the historic districts, have HOA design requirements for driveway gates. We’ll help you understand what your association expects before work starts, and we can match existing ironwork where covenants require it. Call (877) 610-2993 and we’ll walk you through it.
We cover all of Atlanta proper, including ZIP codes 30305, 30306, 30307, and 30308, plus the surrounding communities like Druid Hills, North Decatur, Gresham Park, North Druid Hills, and East Point. If you’re not sure whether you’re in our area, call (877) 610-2993 and ask.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Atlanta Customers Say
"The fence is excellent and it was fairly priced. He is not quick to answer email, so if you need him, ring. He always picks up the phone."
- Rodney Falkenrath"Safety photo eyes on our old gate had been bypassed by whoever serviced it last, which he was genuinely annoyed about on my behalf. Fitted proper sealed ones and wired them the way they should be."
- Otis Redmond"He builds the gates himself in his own shop. You can go and look at it. That is not something you can say about the outfits that just order a panel in."
- Doreen Whitfield