Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Atlanta
Gate parts and welding work in Atlanta usually falls into two camps: a hinge that has finally let go on a heavy ornamental gate, or a post that has drifted so far out of plumb the gate binds against the ground every time it swings. We fix both on site, with a welder in the truck and a live person answering the phone at (877) 610-2993. Hal Gatewood has run this shop since 2001, and he still takes every call himself around the clock. If you live in Buckhead, Inman Park, Grant Park, or anywhere inside the perimeter, we can typically have a truck out to you within 24 to 48 hours for a free estimate, and a lot faster when a gate has failed shut and you can’t get a car in or out.
What separates Atlanta gate repair from anywhere else is the dirt under your posts. More on that below, because it changes everything about how we weld, what we replace, and what you should expect to pay.
Why Gatewood Fence & Gate Is Atlanta’s Preferred Gate Parts & Welding Company
We’re the shop that other Atlanta homeowners call after a national outfit has already quoted them a full gate replacement for what was really a repairable hinge or a post that needed re-setting. That repair-first philosophy is not a marketing line. Hal will stand in your driveway, look at the gate, and tell you what actually needs fixing. If he can weld the rail back straight and remount the hinge for a fraction of a new gate, he’ll say so. The name is on the shop, and the shop is down the road, which is the oldest accountability there is.
Every job we do in Atlanta carries the 90-Day Done Right Promise in writing. If it’s not right, one call brings Hal back, no runaround. We service nine major gate brands including Viking, Ghost Controls, and DoorKing, and we stock common parts locally so Atlanta customers aren’t waiting a week on a shipment. Calls get answered by a live person 24/7, not an answering service. And our pricing is quoted and agreed before any work starts, so the number on the invoice matches the number you approved.
We’re locally owned and owner-operated, with a published address and license number anyone can look up. Hal’s name is on every invoice. That matters in a city where tree canopy, red clay, and aging Buckhead gate drives create repair problems that a technician from out of state has never seen before.
Our Gate Parts & Welding Services in Atlanta
Our Gate Parts & Welding team handles the full range of repair and fabrication work on-site, which means your gate stays in your driveway. We don’t haul it back to a fab shop unless the damage is catastrophic, and even then, we do as much on-site as possible. Here is the local reality for the four most common services we perform in Atlanta.
Hinge Replacement
On a heavy wrought-iron swing gate in any Atlanta neighborhood, the hinge is the first point of failure. When a hinge wears or breaks, the gate drops, drags, and eventually stops closing on the safety photocell. In areas like North Druid Hills and Gresham Park where gates hang over sloped driveways, that failure is accelerated by gravity working against the hinge barrel. We replace hinges with heavier-rated steel, weld them true, and remount the gate so it swings clean through the full arc.
Post Replacement
A gate sags in the hinge post, not in the middle, and that is where we start. Atlanta’s red Georgia clay expands when wet and contracts when dry, which pushes shallow-set posts out of plumb season after season. We set replacement posts in concrete footings that extend well past the clay layer, often using a jig to hold the post at exactly true plumb while the concrete cures. In Buckhead, where 1997 to 2007 estate gates are hitting end-of-life on their original posts, this is the single most common job we do.
Rail Repair
Atlanta is one of the most tree-canopied major cities in the US. When a summer thunderstorm drops a limb on your gate, the top rail or rack-and-pinion track is usually what bends or shears. We cut out the damaged section, weld in new steel, and grind the joint smooth so the operator moves the gate without skipping teeth. A bent arm from a limb strike is nearly always repairable, and we can usually do it in one trip.
Custom Welding
Inman Park, Grant Park, and other early-1900s Atlanta neighborhoods are full of Craftsman and Victorian homes with ornamental gates that were retrofitted onto original brick or stacked-stone columns. Matching the original scrollwork, picket spacing, and finish on those gates takes a welder who understands what the original fabricator was doing. Hal has been welding and fabricating custom gate work since 2001, and he can match older wrought-iron details well enough that the repair disappears into the original design.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Atlanta
We’re certified to service nine major gate brands, and we stock parts for the ones Atlanta homeowners actually use. Viking and Ghost Controls operators are common on suburban swing gates in North Decatur and Gresham Park. DoorKing slide-gate operators show up on a lot of commercial and large residential properties inside the perimeter. Elite swing-gate arms are common on Buckhead estates built in the late 1990s. We keep common boards, arms, remotes, and photo-eyes in stock so a repair doesn’t stall out waiting on a shipment. If we don’t stock the exact part on the truck, we can usually source it within 48 hours and have it installed by the end of the week.
Common Gate Parts & Welding Problems We See in Atlanta Homes
- Red clay post heave. Atlanta’s clay expands and contracts with seasonal moisture, and any post set in a shallow footing will drift a little further out of plumb each wet-dry cycle. The gate starts dragging, then binding, then failing to close. A post replacement with footings that extend past the clay layer fixes it for good.
- Storm-dropped limbs on rails and arms. The dense canopy that makes Atlanta beautiful also drops heavy limbs during summer thunderstorms and ice storms. A limb strike bends the gate arm, shears rack teeth, or twists the top rail. We cut, straighten, weld, and remount so the operator works smoothly again.
- Aging Buckhead swing-gate drives. In 30305, a huge wave of high-end automated driveway gates were installed between 1997 and 2007. Those swing-gate motors and control boards are now failing in a near-simultaneous wave. We frequently replace the drive system and the hinge post at the same time, because the hardware and the footing aged together.
- Hinges on gates retrofitted to masonry columns. Early-1900s Craftsman and Victorian homes in historic neighborhoods often have gates hung on original brick or stacked-stone columns that were never engineered for motorized loads. Hinges pull loose from weakened mortar, and the gate tilts. We weld reinforced mounting plates and re-seat the hinges so the column isn’t doing work it was never built to do.
Pricing for Gate Parts & Welding in Atlanta, GA
Hinge replacement on a standard residential swing gate in Atlanta typically runs $180 to $420 per hinge, depending on the weight of the gate and whether we need to reinforce the mounting point. Post replacement, including excavating the old footing, setting a new steel post in concrete past the clay line, and remounting the gate, runs $450 to $1,200 per post. Rail repair for a limb-struck or bent rail usually falls between $220 and $650. Custom welding for ornamental repairs, scrollwork matching, or reinforcing a cracked joint runs $150 to $900 depending on the scope. Every quote is written, fixed, and agreed before we touch your gate. We offer $40 off any repair over $200, a free second opinion on any written estimate, no trip charge inside the county, and a permanent 10% discount for seniors and veterans.
We Also Serve Cities Near Atlanta
Our Gate Parts & Welding in Atlanta service area extends to Druid Hills, North Decatur, Gresham Park, and North Druid Hills. If your gate sits in one of those communities, the same crew, the same written promise, and the same flat pricing apply. Call (877) 610-2993 and a live person will pick up.
Serving Atlanta, GA - Our Local Coverage Area
We’re based in the Atlanta area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Atlanta
Sagging in the spring is almost always post heave, not a loose hinge. Atlanta’s red Georgia clay expands when spring rains saturate the soil and contracts during dry spells, pushing shallow-set posts out of plumb a little more each cycle. Tightening hinges on a leaning post will not stop the sag, and forcing the gate to close bindings on a post that keeps moving will eventually crack the weld or strip the hinge. The fix is post replacement with footings that extend past the clay layer. You can reach us at (877) 610-2993 for an exact quote and a written price before any work begins, and estimates are free.
Almost always, yes. A bent gate arm or top rail from a limb strike is steel, and steel can be straightened, or the bent section cut out and a new section welded in. The operator itself may need recalibration after the arm is straightened, but the gate does not need to be replaced unless the frame is compromised. We will tell you straight if a repair makes sense, and we will also tell you if the welds near the hinge post cracked during the strike and need re-welding. Every job carries the 90-Day Done Right Promise in writing. Call for a free estimate at (877) 610-2993.
Binding after heavy rain is usually a post that has moved with soil saturation and pulled the gate’s swing path out of alignment with the loop detector. The operator reads the gate as not fully closed and recycles, or the gate physically drags on the ground and stops. We fix it by re-setting the post and re-leveling the gate so the existing loops work as intended. We also check that the receiver and photo-eyes were not knocked out of alignment by the same movement. Call (877) 610-2993 and we will send someone out to put it right.
In Atlanta, an old gate opener that burns out is often the first sign of a gate that has been fighting an alignment problem for months or years. A gate dragging on a shifted post puts extra load on the motor, and the motor fails. When we replace an opener, we always check the hinge and post geometry before we mount the new drive, because putting a fresh motor on a gate that still binds will burn that motor out too. In Buckhead specifically, where 1997 to 2007 swing-gate drives are reaching end-of-life, we see this combination of failures on a regular basis. The 90-Day Done Right Promise covers every part of the job in writing, and we quote a fixed price before starting.
Yes. Older Craftsman and Victorian homes in neighborhoods like Inman Park and Grant Park often have original or early-20th-century ornamentation on their gates, and we have matched scrollwork, picket spacing, and finish work on those gates for years. Hal welds the replacement steel to match the original pattern and then grinds and finishes the joint so the repair reads as part of the original fabrication rather than a patch. We can show you photos of similar work we have done in Atlanta. Call (877) 610-2993 for a free estimate and a written price.
Call Gatewood Fence & Gate for Gate Parts & Welding in Atlanta
If your gate is sagging, binding, twisted from a storm, or the motor is dead, call us at (877) 610-2993. A live person answers, day or night, and Hal will talk you through what he thinks is wrong before we ever send a truck. We work all over Atlanta, from Buckhead to Grant Park to Gresham Park, and we have been doing it since 2001. The estimate is free, the price is fixed before we start, and the 90-Day Done Right Promise is in writing on every job.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Atlanta since 2001.