Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Access Control Across Yonkers
Gate access control in Yonkers means keypads, card readers, phone entry, and video intercoms on gates that were often hung decades before modern safety sensors existed. We service every ZIP in Yonkers, from the dense apartment blocks near the Bronx border in 10701 and 10702 to the steep residential hillsides of 10703, 10704, and 10705. Most Yonkers calls get a same-day visit because we keep parts for older DoorKing, Viking, and Linear control boards on the truck. Call (877) 610-2993 and a live person answers, day or night.
Why Gatewood Fence & Gate Is Yonkers’s Preferred Gate Access Control Company
Hal Gatewood started this company in 2001, and his name is still on the shop and every invoice. When a Yonkers apartment building on South Broadway calls about a dead intercom on a 1940s iron gate, the person who answers the phone knows what that gate looks like. We have worked on pre-WWII building security gates in Getty Square, automated driveway gates off Central Park Avenue, and rusted swing gates on the steep streets below Park Hill. Hal’s crew welds on site, which matters when the post is rotted and the gate is sagging past the safety photocell.
We are licensed and insured. Every job carries the 90-Day Done Right Promise in writing: if it is not done right, one call brings Hal back, no runaround. Yonkers homeowners and property managers call us because the estimate we give over the phone is the price on the invoice. No trip charge inside the county. $40 off any repair over $200. Seniors and veterans get a permanent 10% discount. And a live person answers around the clock, not a voicemail or an out-of-state call center.
Nobody here uses the word “nationwide.” The shop is local, the address is published, and the license number is right there for anyone to look up. That is the oldest accountability there is.
Our Gate Access Control Services in Yonkers
Our Gate Access Control team handles everything from a single worn keypad on a Park Hill driveway gate to full card reader and video intercom retrofits on apartment buildings near the Bronx line. Here is how we approach the most common requests in Yonkers.
Keypad Entry
We install and repair keypad entry on gates throughout Yonkers, and we push stainless steel housings hard in this city. The combination of Hudson River moisture and hillside road salt eats through standard powder-coated keypad boxes in two or three winters. Last winter we rebuilt the hinge post on a rusted 1930s swing gate off Park Hill Avenue. The original keypad housing had corroded so badly it was shorting the control board. We moved the keypad to a stainless box, replaced the post base, and re-hung the gate with sag correction. A typical keypad entry retrofit in Yonkers runs $275 to $650 depending on whether we are reusing the existing wiring or pulling new.
Remote Control
Yonkers driveways sit on some of the steepest grades in Westchester, especially in Nodine Hill and the streets climbing up from Riverdale Avenue. That constant gravity load means remote control receivers and transmitters get used harder here than on flat lots. We program and replace remotes for LiftMaster, Linear, Viking, Ghost Controls, DoorKing, and Mighty Mule systems. If your remote stopped working after a big freeze-thaw cycle, there is a good chance the receiver board took moisture damage. Remote replacement and programming in Yonkers generally runs $85 to $220 per remote, less if the receiver is fine and it is just a pairing issue.
Phone Entry
Phone entry intercoms on Yonkers apartment gates are a specialty of ours because so many buildings in 10701 and 10702 still run telephone entry panels from the 1980s and 1990s. Those aging panel housings crack, the keypad membranes wear out, and the wiring corrodes where the conduit enters the building. We can often rebuild the panel in place rather than tearing out the whole system. Replacing the panel face and control board in Yonkers typically runs $450 to $1,100 depending on the brand and whether we are pulling new wire.
Card Reader
Card reader access control is common on Yonkers condo buildings and gated parking lots. Proximity readers standing out in the salt spray fail at the solder joints and the weather gasket. We replace readers, upgrade old mag-stripe systems to proximity or key fob, and tie them into existing controllers where the wiring is still solid. A single card reader replacement in Yonkers runs $180 to $400. A full retrofit with new controller and power supply is typically $900 to $2,500 depending on how many tenants are enrolled and whether we are reusing the old conduit.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Yonkers
We are certified to service nine major gate brands, and for Yonkers work we keep a deep bench of DoorKing, Viking, and Linear parts on hand because those three dominate this city’s older apartment buildings and pre-2000s residential installs. We also service LiftMaster, FAAC, BFT, Ghost Controls, Elite, and Mighty Mule systems. We stock common relay boards, keypad membranes, photocells, and power supplies locally so a Yonkers repair does not wait on a parts shipment from somewhere else. When a legacy DoorKing board finally dies on a Ludlow Street apartment gate, we usually have the replacement on the shelf.
Common Gate Access Control Problems We See in Yonkers Homes
- Salt-corroded keypad and card reader housings. Yonkers’s steep hillside streets get some of the heaviest municipal salt treatment in Westchester County all winter. Combined with moisture off the Hudson, that salt spray corrodes exposed access control housings months faster than in flat inland towns like White Plains or Mount Vernon.
- Legacy control boards without modern entrapment protection. Pre-WWII apartment gates in 10701 and 10702 often still run original DoorKing or Viking boards made before UL 325. Those boards lack modern entrapment protection, and retrofitted safety photocells frequently mismatch the older relay logic, causing intermittent failures that are hard to diagnose.
- Motor burnout from gravity load on sloped driveways. Driveways in Nodine Hill and Park Hill pitch steep enough that swing gate operators run under constant load. That burns out motors early and throws rack and pinion alignment off on slide gates, which then trips the safety sensor and locks the gate in place.
- Rotted gate posts that drag the access control system out of alignment. A gate sags at the hinge post, not in the middle. When the post rots from salt and freeze-thaw, the gate drops, the photocell beam breaks, and the access control system shuts down. Fix the panel without addressing the post and you will fix it twice.
Pricing for Gate Access Control in Yonkers, NY
Here are honest ranges for the most common access control jobs we quote in Yonkers. Every price is quoted and agreed before any work starts, in writing.
| Service | Typical Yonkers Price Range |
|---|---|
| Keypad entry replacement (stainless housing) | $275 - $650 |
| Remote control replacement and programming | $85 - $220 per remote |
| Phone entry panel repair or replacement | $450 - $1,100 |
| Card reader replacement | $180 - $400 |
| Safety photocell retrofit (including labor) | $250 - $600 per pair |
| Full video intercom retrofit on existing gate | $1,200 - $3,800 |
What moves the price in Yonkers: whether the existing wiring and conduit can be reused, the age and condition of the gate posts, the brand of the control board, and how much corrosion we have to cut out. We give a free written estimate before any work starts. Call (877) 610-2993 to schedule one.
We Also Serve Cities Near Yonkers
Along with Gate Access Control in Yonkers, we regularly work in Bronxville, Woodlawn, Riverdale, and Mount Vernon. Same crew, same 90-Day Done Right Promise, same live person answering the phone at (877) 610-2993.
Serving Yonkers, NY - Our Local Coverage Area
We’re based in the Yonkers area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Access Control in Yonkers
Yonkers’s steep hillside streets receive some of the heaviest municipal salt treatment in Westchester County from November through March, and the Hudson River Valley location adds constant moisture to the equation. That combination creates an accelerated corrosion cycle that rusts hinge posts, eats through keypad and card reader housings, and shorts out electrical contacts months faster than in flatter inland towns like White Plains or Mount Vernon. If your gate access control is failing repeatedly, corrosion is usually the root cause. Call (877) 610-2993 and we will find it.
In most cases, a 1950s gate in southwest Yonkers can be retrofitted with a video intercom without replacing the operator, as long as the gate posts are structurally sound and the control board can be upgraded to a modern UL 325-compliant unit. We have done this on pre-WWII buildings in 10701 and 10702 where the original iron gate is still in good shape and only the access control hardware is obsolete. If the post is rotted and the motor is on its last legs, replacement becomes the cheaper answer. We will tell you honestly which side of that line you are on.
There is no hard threshold, but we see keypad entry failures in Park Hill after two to three winters on standard powder-coated housings. Once the finish is compromised and salt spray reaches the circuit board, the keypad will intermittently short, fail to register codes, or lock up entirely. Stainless steel housings and sealed conduit fittings buy you five to ten years. If your keypad has started acting up after a hard winter, call (877) 610-2993 for a free inspection before the board fries completely.
Because the real failure is in the hinge post, not the access control panel. A gate sags in the hinge post, not in the middle. When the post rots from road salt and freeze-thaw, the gate drops, the photocell beam breaks, and the operator starts fighting the extra load. You can replace the keypad or the board, but until the post is rebuilt, the system will keep failing. That is why we weld post bases on site and re-hang gates with sag correction before touching the electronics.
Yonkers follows New York State and federal UL 325 standards, which require monitored entrapment protection on automated gates: either non-contact sensors like photocells or contact edges that reverse the gate when someone or something is in the path. Many older gates in Yonkers were installed before UL 325 and lack these features entirely. Retrofitting safety photocells onto a legacy control board is not always straightforward, especially with older DoorKing or Viking relay logic. We handle that retrofit correctly, and we will not leave a gate operating without the safety features New York requires.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Yonkers and Westchester County since 2001.