Gate Repair in Yonkers - Same-Day Repair, Priced Before We Start

Fast, Reliable Gate Repair Across Yonkers

Gate repair in Yonkers typically costs $185 to $520 for most hinge, post, and realignment jobs, with opener repairs running $245 to $710 depending on the control board and motor condition. We get to Yonkers fast, usually within 60 to 90 minutes for emergency calls, because we keep a full welding rig and common Viking, Ghost Controls, and DoorKing parts on the truck. Hal Gatewood has been fixing gates since 2001, and he treats your gate the same way he treats the ones on his own street. Call us at (877) 610-2993 any hour, and a live person answers, not a recording.

Yonkers is the only city in Westchester County where gate repair techs routinely service both pre-WWII Bronx-border apartment building security gates and automated driveway gates on steep, salt-heavy hillside lots. That means we carry dual expertise in legacy wrought-iron hardware and modern slope-stressed operators, because a tech who only knows one side of that equation will misdiagnose the other. We see it happen. A gate sags in the hinge post, not in the middle, and that is where we start.

Why Gatewood Fence & Gate Is Yonkers’s Preferred Gate Repair Company

We are locally owned and owner-operated. Hal Gatewood’s name is on the shop and on every invoice, and his published address and license number are there for anyone who wants to look them up. That is the oldest accountability there is. The person who gives you the quote is the same person who shows up to do the work, and if it is not done right, the 90-Day Done Right Promise means one call brings him back. No runaround. The promise is stamped in writing on every job, not buried in fine print.

Yonkers customers call us because we answer the phone with a live person 24 hours a day, 7 days a week. Not a voicemail, not a call center three states away, not a chatbot. You get a person who knows gates. We have been doing this since 2001, which means we have already seen every failure mode the Hudson River Valley climate can throw at a gate. From the dense apartment blocks near the Bronx border in 10701 to the hillside driveways up in 10703, we know the housing stock, the salt, the grades, and the old iron.

And unlike companies that want to sell you a new gate the moment one hinge fails, we fix first. We weld on site, in your driveway. If the panel is sound and the post is the problem, you do not need a new gate, you need the post replaced correctly. That is the difference between a company and a repairman.

Our Gate Repair Services in Yonkers

Electric Gate Repair

Electric gate operators in Yonkers fail in predictable ways, especially on the hilly east side where slope stress burns out motors and wears drive gears. We service controllers, safety photocells, keypads, loop detectors, and motors for nine major brands including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. If your opener is pre-2000 and the control board will not accept modern safety retrofits, we will tell you honestly whether a board swap makes sense or whether whole-operator replacement is cheaper than pouring money into obsolete electronics.

Automatic Gate Repair

Automatic gates on Yonkers slopes face a problem flat-dwelling gate owners never see: gravity loading. On a steep Park Hill or Nodine Hill driveway, the gate’s own weight works against the operator constantly. Rack and pinion systems bind. Slide gates drift off their tracks. Motors run hot. We reset alignment, replace worn drive components, and set limit switches properly so the gate is not fighting the hillside every cycle. An automatic gate on a slope will always need more attentive maintenance than one on flat ground, and we set ours up accordingly.

Hinge & Post Repair

This is the repair we do most often in Yonkers, and it is the one other companies skip. The original 1920s through 1950s ornamental iron gates on southwest Yonkers properties are usually built well, but their hinge posts have been sitting in salt-laden runoff for decades. The post rots at the base, the gate drops, the latch stops lining up, and someone tries to fix it by adjusting the latch. That is fixing the panel twice because the post was never addressed. We cut out the rotted footing, set a new galvanized steel post in concrete, and re-hang the gate so it swings true. The gate stays in your driveway the whole time.

Gate Realignment

A gate that drags, sticks, or will not latch is almost never a bent panel, it is a failed post or worn hinge. We realign gates by addressing the structure underneath, not by grinding the latch plate until it sort of works. On steep Yonkers driveways, misalignment also causes the opener to work overtime, which shortens motor life. Fix the alignment and the opener stops working so hard. A sagging gate fixed properly will swing with two fingers again, even if it has been dragging for ten years.

Trusted Brands We Service in Yonkers

We are certified and comfortable working on the gear already installed in Yonkers homes: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Viking and Ghost Controls are common on residential driveway gates around 10704 and 10705, and DoorKing shows up frequently on older apartment building security gates toward the Bronx border. Because we stock common parts and boards locally, we are often able to complete repairs in one visit instead of ordering a part and making you wait. That matters when your gate is stuck open at midnight.

Common Gate Repair Problems We See in Yonkers Homes

• Rusted-out hinge posts on hillside lots. Yonkers streets get some of the heaviest municipal salt treatment in Westchester County, and when that salty slush drains toward a gate post on a downgrade, the base corrodes fast. We see posts that look fine above ground but are paper-thin at the footing.
• Obsolete control boards on pre-2000 apartment gate operators. Southwest Yonkers apartment buildings in 10702 and 10705 often have gate operators installed before modern safety standards. The boards cannot accept current photocell or keypad retrofits, so the honest answer is usually full operator replacement rather than piecemeal board swaps.
• Slide gate track misalignment on steep driveways. Gravity does the work on a sloped track, pulling the gate off the rack and pinion over time. The motor compensates until it burns out. We see this consistently in the hilly northeast neighborhoods of Yonkers, and it is rare in flatter towns.
• Wrought-iron gate sag from original 1940s and 1950s hinges. The ornamental iron gates on older Yonkers row houses were built to last, but their hinges were not. After 70-plus years and decades of Hudson River Valley freeze-thaw cycles, the hinge pins wear oval and the gate drops. This is a welding and re-pinning job, not a replacement job.

Our crew recently rebuilt a sagging swing gate on a Park Hill driveway where the original 1940s hinge post had rusted through at the base due to years of road-salt runoff. We cut out the rotted post footing, set a new galvanized steel post in concrete, and installed a LiftMaster operator with a safety photocell pair, realigning the gate so the rack and pinion no longer binds on the slope. The gate had been dragging for years, and the homeowner had been quoted a full replacement by another company. The fix cost less than half of that quote, and the gate still works fine.

Pricing for Gate Repair in Yonkers, NY

We Also Serve Cities Near Yonkers

Our Gate Repair service covers the whole Yonkers area plus nearby communities. If you live in Bronxville, Woodlawn, Riverdale, or Mount Vernon, we are still your local shop. We know those streets too, and we bring the same repair-first approach and upfront pricing. For more on our service area, see Gate Repair in Yonkers and the surrounding towns.

FAQs - Gate Repair in Yonkers

Why does my automatic gate opener on a Yonkers hillside driveway burn out motors faster than my friend’s in White Plains?

Your friend in White Plains has a flat lot. Your gate is fighting gravity on every open and close cycle, which means the motor works harder, the limit switches fail sooner, and the drive gears wear faster. On steep Yonkers drives, we always check the gate’s balance and track alignment before condemning the motor, because a misaligned gate on a slope will kill a new motor in months, not years. Clean up the alignment and the motor stops overworking. Call (877) 610-2993 for an on-site evaluation.

Can you retrofit my 1950s ornamental iron gate with a modern automatic opener, or does it need full replacement?

Most of the time, yes, the gate can stay. We retrofit 1920s through 1950s wrought-iron gates with modern operators regularly in Yonkers, as long as the hinge posts are structurally sound and the gate swings or slides freely. If the post is rotted, we replace the post, not the gate. If the gate’s weight or design makes a retrofit impractical, we will tell you that plainly and show you the math. You never have to agree to a new gate when a retrofit is the right answer.

Do apartment building security gates in southwest Yonkers require UL 325 entrapment protection even if they are old?

Yes. UL 325 is a safety standard for gate operators, and it applies regardless of the age of the gate. Buildings in 10701, 10702, and 10705 with older operators often lack current photocell, edge sensor, or reversing mechanism protection. If we repair or service those operators, we bring them up to standard, which sometimes means replacing the control board or the whole operator. We will not put a band-aid on an unsafe gate, and we will explain exactly what the code requires and why.

Why do my gate hinges rust out so quickly in Yonkers compared to Mount Vernon?

Yonkers gets more salt than Mount Vernon because of the topography. The city’s steep hillside streets require heavy road-salt application from November through March, and that salted slush drains downhill and collects at gate post footings. Add Hudson River moisture and the freeze-thaw cycle, and you get a corrosion environment that eats mild steel hinges years faster than in flatter inland towns. We use galvanized or sealed-bearing components on replacement hinges, which is the only way to make them last in this city.

Can a sagging gate be fixed by straightening the panel, or is the hinge post the real problem?

The hinge post is almost always the real problem. A gate sags because the post that supports it has moved, rotted, or loosened. The panel itself rarely bends, it just drops. If you straighten the panel without fixing the post, you will fix it twice. We start every sagging gate diagnosis at the hinge post, because that is where the weight lives. On Yonkers hillside properties, the post is usually the failure point, not the gate.

Get Your Yonkers Gate Fixed Today

If your gate is sagging, stuck, or just making a sound it never made before, call us. We will give you an honest diagnosis, a written price before any work starts, and a repair that respects the gate you already have. The name is on the shop, and the shop is down the road, that is the oldest accountability there is. Call (877) 610-2993 now, and a live person will answer.

Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Yonkers and surrounding Westchester communities since 2001.