Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Mount Vernon, NY
Gate repair in Mount Vernon typically costs $180-$480, and most jobs are finished the same day we arrive. The work here is different from other Westchester towns: block after block of pre-WWII brick homes still carry ornamental wrought-iron gates from the 1920s through the 1940s, and the repairs are mechanical, not electronic. If your South Side gate won’t latch or your Fleetwood driveway gate is sagging off the post, call (877) 610-2993. A live person answers, and we’ll give you a real number over the phone.
Why Mount Vernon Homes Are Different
Mount Vernon sits directly on the Bronx border and is one of the most densely built small cities in New York State. The South Side and Fleetwood especially are block after block of pre-WWII attached and semi-attached brick homes, many still carrying the ornamental wrought-iron pedestrian and driveway gates installed when the houses were built 70 to 100 years ago. That changes the repair picture completely. In newer Westchester suburbs to the north, the typical call is an automated driveway gate that stopped responding. Here, the dominant need is mechanical: corroded hinges, sagging frames, and posts that have shifted out of plumb on legacy iron installations.
The climate does not help. Westchester’s freeze-thaw cycle runs from November through March, with temperatures crossing the freezing mark over and over. Concrete expands when water in it freezes, and that heaves gate posts seasonally. Iron hinge barrels crack or seize. Heavy road-salt application on Mount Vernon’s dense street grid accelerates rust on gates close to the curb, particularly on corner lots. On many South Side and Fleetwood blocks, nearly every attached home was built with an iron gate in the same construction era, meaning the same original hardware is failing across an entire street simultaneously. A technician who stocks period-appropriate drop rods, weld-on hinge pins, and flat-bar stock for fabrication will close jobs on the spot that competitors have to reschedule.
Gate Repair in Mount Vernon
Gate repair in Mount Vernon usually means one of two things: a sagging iron gate that hasn’t latched right in years, or an electric opener that stopped working and left the gate stuck halfway. Most repairs we handle in Mount Vernon run $180-$480, and the majority are finished the same day we arrive. If you’re on the South Side or up in Fleetwood with an original 1930s gate that won’t close, we bring the welding equipment and the parts to fix it in your driveway.
Hinge & Post Repair
In Mount Vernon, hinge and post repair is the bread and butter of our gate work. The pre-WWII brick rowhouses from 10550 up through Fleetwood were built with ornamental iron gates that are now 70 to 100 years old. The hinge barrels seize from decades of road salt, then snap the hinge pin when somebody forces the gate. We cut out the old barrel, weld in a new one, and re-set the post so the gate hangs plumb. Hinge and post repairs in Mount Vernon typically run $250-$480.
Weld & Rust Repair
Mount Vernon’s dense street grid puts salt on every curb, and iron gates close to the curb rust faster than anything else on the property. We see corner-lot gates in 10552 with bottom rails rusted through, and courtyard gates where the pickets have started separating from the frame. We repair in place: cutting out the rotted section, welding new flat-bar stock to match the original profile, and treating the surrounding metal before repainting. Weld and rust repair is usually $180-$400. You keep the original gate. You don’t pay for a new one that wouldn’t match the ironwork on your block.
Gate Realignment
A gate sags in the hinge post, not in the middle, and that’s where we start. Westchester’s freeze-thaw cycle works on concrete post footings from November through March. The footing heaves a fraction of an inch, the post tilts, and suddenly the drop rod doesn’t line up with the hole in the walk. Resetting a heaved post runs $300-$600, depending on the size of the gate and whether we’re re-pouring the footing. We re-set the post, re-plumb the gate, and weld the hinges back square. Fix the panel without the post and you’ll fix it twice. We’d rather do it once.
Electric Gate Repair
Electric gate repair in Mount Vernon covers everything from a dead operator to a gate that reverses for no reason. We service LiftMaster, FAAC, Linear, DoorKing, Viking, and Mighty Mule openers. With the older operators still running on some Fleetwood and South Side driveways, the limiting switches wear down, the control board misreads the load, and the gate stops mid-cycle. Electric opener diagnostics and repairs run $220-$550, and a full operator replacement with safety sensors is $900-$1,500 installed. We test the operator, replace what needs replacing, and calibrate the limits so the gate closes without slamming.
If you need more detail on any of these repairs, visit our main Gate Repair page.
Can you retrofit an original 1930s Mount Vernon iron gate with a modern automatic opener, or does the gate itself need replacing?
Most 1930s iron gates in Mount Vernon can be retrofitted with a modern opener if the frame, hinges, and posts are structurally sound. We evaluate the gate’s weight, swing geometry, and hinge condition first. Heavy ornamental gates with seized hinges will burn out a new operator in months, so hinges get rebuilt before the opener goes on. Call (877) 610-2993 for an exact quote - estimates are free.
My Fleetwood block has identical iron gates from the 1930s and several neighbors need hinge repairs. Can you fix multiple gates in one visit?
Yes, and this happens regularly in Fleetwood and on the South Side. Because entire Mount Vernon blocks were built with the same wrought-iron gates from the 1920s-1940s, the same hinge-post fatigue and snapped drop rods fail on half the houses at once. We dispatch with period-appropriate flat-bar stock and weld-on hinge pins, so we can move down the block and fix three or four gates in the same afternoon. Call (877) 610-2993 to schedule a block visit.
Gate Installation in Mount Vernon
Gate installation in Mount Vernon usually runs between $900 and $7,500, depending on whether you’re replacing a legacy iron pedestrian gate on a South Side rowhouse or building an automated double driveway gate in Fleetwood. Most single walk-through gate installations here land in the $1,200-$3,200 range, and we quote that price in writing before any work starts. Hal Gatewood is the person who will come look at your property, take the measurements, and build the gate.
Driveway Gate Installation
Driveway gates in Mount Vernon tend to be tighter to the property line than in the northern suburbs, because lots here are narrow and shared-wall construction eats up space. A double swing gate might not clear the sidewalk, so we usually spec a sliding gate or a single swing with proper setback from the road salt line. A single swing driveway gate starts around $2,500 and can reach $5,500 for a wider or heavier build. We handle the full build: posts set below frost depth, hinge alignment on the actual grade, and a gate that stays square through the freeze-thaw heave that hits Westchester every winter.
Pedestrian Gate Installation
The classic Mount Vernon pedestrian gate is ornamental iron from the 1920s, 30s, or 40s, and it has outlived its hardware several times over. A standard walk-through iron pedestrian gate, custom-built and hung on new steel posts, typically runs $1,200-$2,800. We fabricate replacement frames and re-hang doors on new weld-on hinge pins so the gate swings clean and latches firm. When an original wrought-iron gate is too far gone to repair, we build a period-appropriate replacement that matches the house, not a generic box-store panel.
Sliding Gate Installation
On corner lots off North Columbus Avenue or in the 10552 blocks where the curb line is tight, a sliding gate often makes more sense than a swing gate. There’s less room for the gate to arc into the street, and the track can be run along the foundation wall rather than eating up usable yard. Sliding driveway gates run $3,200-$7,500, largely because the track, steel frame, and fabrication hours add up fast. We install cantilever and track-type sliding gates, sized to the driveway width and built to handle the salt spray that comes with being close to the curb.
For more on our installation process, see Gate Installation.
How does gate installation pricing in Mount Vernon compare to nearby Westchester towns?
Mount Vernon pricing tends to run slightly lower on labor than the wealthier towns to the north, but the work is more fabrication-heavy because so many properties still have 70-to-100-year-old iron gates that need custom brackets, welded pins, and hand-formed replacement scrollwork. A pedestrian gate here typically runs $1,200-$2,800, while a full sliding driveway gate lands between $3,200 and $7,500. You’ll get an exact number after we measure the site. Call (877) 610-2993 to set up a free estimate.
What warranty do you offer on gate installation in Mount Vernon?
Every installation we do carries the 90-Day Done Right Promise, in writing. If something isn’t right within 90 days, we come back and fix it. No charge, no hedging. It’s not “up to” 90 days and it’s not a fine-print situation. It’s Hal’s name on the work, and he stands behind it. Call (877) 610-2993 for a free estimate and we’ll put everything in writing before we start.
Gate Motor & Opener in Mount Vernon
Gate motor and opener work in Mount Vernon usually means one of two situations. Either an original iron gate from the 1920s or 1930s needs a motor fitted where none existed before, or an older opener that someone installed a decade ago has finally quit. We handle both, and we handle them on-site. If you’re on the South Side, in Fleetwood, or anywhere between the Bronx line and the Cross County, call (877) 610-2993 and you’ll get a live person.
Motor Installation
Installing a motor on a gate in Mount Vernon is rarely a bolt-on job, because most of the gates here were never designed for automation. A 1930s wrought-iron leaf on a Fleetwood brownstone weighs more than the operator’s spec sheet accounts for, and the post it hangs from has been shifting for eighty years. We account for that. We square the post, reinforce the hinge side if needed, and match the motor to the actual weight and duty cycle of the gate. A full motor replacement on a single-family gate generally falls between $850 and $1,600 installed.
Motor Repair
Most motor failures we see in Mount Vernon are not the motor itself. They’re the result of a gate binding against a frost-heaved track, a clutch that’s been slipping for months, or corrosion from road salt eating through wiring near the curb. Gate motor repair in Mount Vernon typically runs $180 to $340 for common fixes like limit switches, control boards, clutch adjustments, and wiring repairs. We diagnose the whole system, not just the part that finally stopped. That’s the difference between a repair that lasts and one that strands you again in February.
Slide Motor
Slide gates are the workhorse of Mount Vernon’s busy streets, especially on corner lots where a swing gate would block the sidewalk or the neighbors’ shared access. We install and repair slide motors from DoorKing, Viking, and Ghost Controls. Slide motor installations on shared driveways or heavy ornamental gates run higher, often $1,600 to $2,800, because the track and footings almost always need correction before the operator goes on. On South Side blocks where the concrete has settled over decades, a slide track that’s off by a half inch will burn out a motor in a season. We level the track first, then set the motor. It is not the fast way; it’s the honest way.
Learn more about our motor and opener services on our Gate Motor & Opener page.
Can you replace the motor on my original 1930s iron gate in Fleetwood without damaging the ornamental work?
Yes. We do this regularly on Fleetwood’s original gates from the 1920s through the 1940s. The motor mounts to the post and the gate leaf using brackets we fabricate on site when the original geometry doesn’t match modern operators. We never weld directly onto ornamental scrollwork unless there’s no alternative, and when we do, we make the attachment clean and reversible. The ironwork stays intact. Call (877) 610-2993 and Hal can look at your gate.
Does a battery backup make sense for a gate opener on a dense Mount Vernon street?
Yes, and we recommend it for most Mount Vernon installations. Dense streets mean more vehicle and foot traffic, a higher chance of storm damage to power lines, and more urgency when a gate won’t open because an emergency vehicle or a resident needs access. A battery backup keeps the gate cycling through most outages and adds about $300 to $600 depending on the operator. Call (877) 610-2993 to discuss whether it fits your setup.
Gate Access Control in Mount Vernon
Gate access control in Mount Vernon usually means one of two things: retrofitting a keypad, phone entry system, or video intercom onto an older ornamental iron gate, or repairing the operator and posts that are already there. The difference in Mount Vernon is that most gates are 70 to 100 years old. They were never designed for electronics. The post footings are shallow, the iron has been through decades of freeze-thaw, and the wiring has to be routed without tearing into century-old brick.
Keypad Entry
A keypad lets you punch in a code instead of fumbling for a remote or walking out to the curb. On a 1930s ornamental gate in the South Side, the trick is mounting the keypad so it doesn’t tear out the hinge-post welds. We reinforce the post first, run the wiring through the existing iron frame where we can, and program codes on the spot. Most keypad retrofits in Mount Vernon run $350 to $750, depending on whether we’re adding a new operator or tying into the one you have.
Phone Entry
Phone entry systems call your cell phone when someone buzzes at the gate. You talk to them, press a button, and the gate opens. It’s a good fit for Mount Vernon’s two-family homes and small apartment buildings, where you don’t want to hand out gate codes to every visitor. Installation typically runs $600 to $1,100 in Mount Vernon. We’ll quote it before we start, and that’s the number you pay.
Video Intercom
Video intercom adds a camera to the entry unit so you can see who’s at the gate before you open it. On tight Mount Vernon lots where the gate sits close to the street, wiring is often the biggest part of the job. Older brick walls complicate things. We fish wires behind the iron where possible, or use wireless video units where the layout allows. Expect $800 to $1,400 for a solid video intercom setup in Mount Vernon.
See our full access control offerings at Gate Access Control.
Can a 1930s ornamental iron gate in Mount Vernon be retrofitted with a keypad entry, or does the whole gate need replacing?
Yes, a 1930s ornamental iron gate can almost always be retrofitted with keypad entry. The gate itself is usually fine. What matters is the post and hinges. If the post is cracked, heaved, or rusted through at the base, we reset and reinforce it before mounting anything. You pay for the keypad and the post work, not a whole new gate you don’t need. Call (877) 610-2993 and we’ll tell you what your gate needs.
What is the cheapest fix for a sagging iron gate on a 10550 row house?
The cheapest lasting fix is often a weld-on hinge pin and a post reinforcement, not a new gate. Sagging usually means the hinge pin has worn or the post has leaned. We weld a new pin sleeve into the post in your driveway, often for $250 to $600 depending on condition. It’s half the cost of a replacement and keeps your original iron. Call (877) 610-2993 for a free estimate.
Gate Parts & Welding in Mount Vernon
Gate parts and welding in Mount Vernon is where we separate repair from replacement. Most of the iron gates in this city are original to the property, and the parts that fail - hinge barrels, drop rods, bottom rails, pickets - haven’t been manufactured since the Truman administration. We don’t order them. We make them. Hal carries a mobile welding rig, flat-bar stock in common profiles, and hinge pins sized to the hardware we see on South Side and Fleetwood gates every week.
On-Site Welding
We weld in your driveway, not in a shop across the county. A gate that has to be hauled away for repair is a gate that may not come back the same week, and on a tight Mount Vernon lot that leaves your property open to the street. We cut out rotted sections, weld in new material to match the original profile, and grind it clean so the repair disappears into the gate. Hinge pin and post reinforcement welding runs $250-$600 depending on how much fabrication the post needs.
Custom Fabrication
When a bottom rail is rusted through or a picket has snapped off at the weld, we don’t sell you a replacement gate. We measure the original profile, cut matching flat-bar or round stock, and weld it in place. The gate keeps its character, and you don’t get a mismatched panel that makes the house look like it got dressed in the dark. For parts that need to be ordered - operators, control boards, safety edges - we stock the common ones and can get the rest fast.
Period-Appropriate Hardware
On many South Side blocks, the same drop rod design was used on twenty houses in a row. When they start failing, we bring the right stock and weld-on hardware to fix them all. That saves you the hunt for a part that hasn’t been catalogued since 1952. We also handle rack-and-pinion repairs on slide gates, where road salt has chewed through the teeth but the rail underneath is still sound. Cut out the damaged rack, weld in a fresh section, regrease the drive - that’s a $350 to $700 repair versus thousands for a new gate.
More details on our welding and fabrication work are at Gate Parts & Welding.
Can a slide gate with a rusted rack and pinion from road salt be repaired, or does the whole track need replacing?
The rack and pinion itself can usually be repaired by welding in a new rack section, not replacing the whole track. Road salt rusts the teeth, but the rail underneath is often fine. We cut out the damaged rack, weld in a fresh section, and regrease the drive. That’s a $350 to $700 repair in Mount Vernon, versus thousands for a new slide gate. Call (877) 610-2993 and Hal can look at it.
My old gate operator uses a buried loop detector that no longer opens the gate. Can you replace just the loop detector, or do I need a new operator?
In many cases, the loop detector alone can be replaced. We test the loop itself by checking continuity at the controller. If the loop is still good, a new detector is a $200-$350 repair and you’re done. If the loop wire itself has been cut by a shifted driveway slab or tree root, the fix means saw-cutting the concrete and re-installing the loop, which runs $500-$800. At that point, depending on the age of your operator, we may recommend a full replacement. Call (877) 610-2993 and we’ll test it on the spot.
Brands We Service in Mount Vernon
We are certified to service nine major gate brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. We stock common parts for Linear, Viking, Ghost Controls, and DoorKing operators locally, which means most Mount Vernon repairs don’t wait on shipping. If we don’t have it on the truck, we can usually get it next business day. See our brands page for full details.
Pricing for Gate Repair in Mount Vernon, NY
| Service | Typical Range in Mount Vernon |
|---|---|
| Hinge & post repair | $250-$480 |
| Weld & rust repair | $180-$400 |
| Post reset (heaved footing) | $300-$600 |
| Electric opener diagnostics & repair | $220-$550 |
| Full operator replacement with safety sensors | $900-$1,500 |
| Pedestrian gate installation | $1,200-$2,800 |
| Single swing driveway gate installation | $2,500-$5,500 |
| Sliding driveway gate installation | $3,200-$7,500 |
| Gate motor repair (switches, boards, wiring) | $180-$340 |
| Full motor replacement installed | $850-$1,600 |
| Slide motor installation (shared/heavy gates) | $1,600-$2,800 |
| Keypad entry retrofit | $350-$750 |
What pushes price up in Mount Vernon: deep post excavation through clay and old concrete, custom fabrication to match ornamental ironwork, and routing wiring through century-old brick without damaging it. Every price is quoted and agreed in writing before any work starts. The number we give you is the number on the invoice.
Neighborhoods We Serve in Mount Vernon
We cover the whole city, and we’re on the ground in these neighborhoods most weeks. Typical response for a gate repair call in Mount Vernon is same day or next morning, depending on when you call and what the gate needs.
- South Side (10550) - dense rowhouse blocks, original ironwork, tight shared lots
- Fleetwood (10552) - pre-war brick homes and larger driveway gates
- North Side (10553) - mixed housing with a lot of older ornamental iron
- Downtown Mount Vernon (10550) - commercial and residential entry gates
- Oakwood Heights (10552) - varied housing stock, many legacy installations
Service Area - Cities Near Mount Vernon
We work Mount Vernon regularly, and we carry the same tools and stock into neighboring communities. If you’re just outside the city line, we still answer the phone with a live person and we still don’t charge a trip fee inside Westchester County. We also serve Pelham, NY, Pelham Manor, NY, Wakefield, NY, Woodlawn, NY, and Bronxville, NY.
Serving Mount Vernon, NY - Our Local Coverage Area
Gatewood Fence & Gate crews serve Mount Vernon and the communities around it; dispatch is coordinated from our New York City office. The map shows the Mount Vernon coverage area; if your address is on it, we can help.
Also serving nearby: Mount Vernon, NY, Pelham, NY, Pelham Manor, NY, Wakefield, NY, Woodlawn, NY, Bronxville, NY.
FAQs About Gate Repair in Mount Vernon
Most gate repair calls in Mount Vernon get same-day or next-morning response, depending on when you call and what the gate needs. Emergency situations - a gate stuck open, a post pulled away from the wall, a hinge snapped - get priority. A live person answers (877) 610-2993 24 hours a day, and we’ll give you a real arrival window we actually keep.
Most gate repair work in Mount Vernon, including hinge replacement, welding, and operator swaps, does not require a permit. If we’re replacing a post footing or running new power to an operator, your specific situation may require a permit through the city’s building department. We’ll tell you before we start if that’s the case, and we can handle the paperwork if needed.
Yes. We work all four Mount Vernon ZIP codes: 10550, 10551, 10552, and 10557. That includes the South Side’s dense rowhouse blocks, Fleetwood’s older single-family streets, and everything along the Bronx line. Dispatch and scheduling are coordinated from our New York City office, and crews serve Mount Vernon locally.
Call (877) 610-2993 for a free estimate. A live person answers, and we’ll give you a written quote before any work starts. No trip charge inside Westchester County, $40 off any repair over $200, and 10% off for seniors and veterans.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Mount Vernon Customers Say
"Safety photo eyes on our old gate had been bypassed by whoever serviced it last, which he was genuinely annoyed about on my behalf. Fitted proper sealed ones and wired them the way they should be."
- Otis Redmond"He builds the gates himself in his own shop. You can go and look at it. That is not something you can say about the outfits that just order a panel in."
- Doreen Whitfield"Welded the hinge back onto our wrought iron gate on site rather than taking it away for a fortnight. Ground it back and painted it and you cannot see the repair."
- Winston Achterberg