Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Access Control Across Roswell
Gate access control in Roswell usually means one of two things here: a builder-grade operator from a 1990s subdivision that’s finally quit, or a manual wrought iron gate somebody wants to automate for the first time. Either way, we handle it start to finish, including the wiring and conduit runs that should have gone in during original construction but often didn’t. Hal Gatewood has been fixing gates since 2001, and his crew works Roswell neighborhoods from Horseshoe Bend to Willow Springs every week. Call (877) 610-2993 and you’ll get a live person, not a recording.
Why Gatewood Fence & Gate Is Roswell’s Preferred Gate Access Control Company
Most gate companies in this area want to sell a new operator the moment a control board fails. We don’t. Hal fixes the gate in your driveway, welds on site, and stands behind the work with a 90-Day Done Right Promise in writing on every job. That matters in Roswell because so many of your gates are custom ornamental iron from the 1982-2005 building boom. Swapping the whole thing out for a generic aluminum panel would look wrong on a $700,000 house off King Road or along the Chattahoochee corridor.
Roswell homeowners call us because our name and address are published, our license number is something anyone can look up, and the person who shows up is background-checked and uniformed. Hal’s the owner. He answers the phone. You can drive to the shop and look him in the eye. That’s the oldest accountability there is.
We also answer calls 24/7 with a live person. If your gate won’t close at 11 p.m. and your dog is loose or your driveway is exposed to Canton Street traffic, you don’t want a voicemail. You want a human who knows Roswell and will tell you honestly whether it’s a capacitor, a photocell, or a post shifted by red clay heave.
Our Gate Access Control Services in Roswell
We don’t do “access control” as some abstract corporate offering. We install, repair, and upgrade the specific components that let you open and close your gate the way you actually use it. Here’s what that looks like in Roswell.
Keypad Entry
Roswell keypads fail in patterns we’ve come to recognize. Builder-grade installs often ran undersized thermostat wire to keypad posts, and two decades of Georgia humidity later, intermittent entry failures start showing up. We replace the keypad, pull new wire where needed, and set codes the same day. A typical keypad replacement or new install in Roswell runs $180-$420 including wiring, depending on whether we’re pulling new cable through existing conduit or trenching a short run.
Remote Control
If your remote only works within 15 feet of the gate, or stops working after rain, the receiver antenna is usually degraded or the board’s moisture seal has failed. We stock replacement remotes and receiver cards for LiftMaster, Viking, Elite, and DoorKing systems common in Roswell subdivisions. Programming a new remote typically runs $85-$160 when the operator is in good shape. If the receiver board itself is corroded, a board swap runs $340-$650 on most Roswell gates.
Phone Entry
Phone entry systems are increasingly popular on Roswell’s HOA entrance monuments and on large driveway gates where homeowners want visitors to call their cell rather than punch a code. We install and service cellular and landline-based entry systems that dial your phone when a guest presses the call button. A modern phone entry module installed on an existing gate operator in Roswell typically runs $500-$900 including the unit, antenna, wiring, and programming.
Card Reader
Card and fob readers show up most often on Roswell community entrance gates, especially in subdivisions with dual-swing iron gates at the front entrance. We install proximity card readers, program fobs, and integrate them with existing operators from Elite, Viking, and DoorKing. For a community entrance system, a card reader addition with basic integration runs $650-$1,200 in Roswell depending on the existing controller and distance from the power source.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Roswell
We’re certified to service nine major gate brands, and in Roswell the calls skew heavily toward LiftMaster, Elite, Viking, DoorKing, and Ghost Controls. Those are the builders’ choices from the 1982-2005 subdivision boom, and we keep common boards, remotes, receivers, and safety edges on the truck so we don’t make a second trip across town. If your gate has a FAAC, BFT, Linear, or Mighty Mule operator, we work on those too. Our Gate Access Control team sees enough Roswell volume that local parts are stocked, not special-ordered and shipped from somewhere you’ll never visit.
Common Gate Access Control Problems We See in Roswell Homes
Some problems are universal. These are the ones we see over and over in Roswell specifically.
- Control board failure at 15-20 years. Builder-grade LiftMaster and Viking operators installed in the 1990s and early 2000s hit capacitor and board failure on a predictable schedule. Roswell’s housing stock is aging into that window right now, which is why board replacement rather than full operator swap is our dominant service call.
- Red clay heave throwing posts out of plumb. Roswell’s red Georgia clay expands when saturated during spring and summer downpours, then shrinks through dry stretches. That seasonal movement shifts gate post footings, binding swing gates and tripping the operator’s force sensor. The gate sags in the hinge post, not in the middle, and that’s where we start.
- River humidity corroding enclosures and boards. Neighborhoods west of Azalea Drive and along the Chattahoochee corridor consistently show corrosion on control boards and actuator arm bearings that you wouldn’t see a few miles east in the drier upland subdivisions. Moisture intrusion causes phantom keypad failures and intermittent remote drops that don’t show a clear code.
- Undersized original wiring from the builder. Many 1980s and 1990s Roswell gates were wired with 18-gauge thermostat wire never meant for outdoor duty or modern accessory loads. When we upgrade to smart access or add a loop detector, we’re often pulling new direct-burial CAT6 and heavier power cable through the same conduit.
Pricing for Gate Access Control in Roswell, GA
You deserve actual numbers, not a vague “give us a call.” Here’s what Roswell work typically costs. Keypad replacement or new install runs $180-$420. Remote programming runs $85-$160. A receiver board swap runs $340-$650. Phone entry modules run $500-$900. Card readers for community gates run $650-$1,200. A full operator replacement on an existing swing gate typically runs $1,800-$3,400 in Roswell depending on size, brand, and whether underground operator arms are involved. Every price is quoted and agreed before work starts. You won’t get a call from the truck saying it’ll be more. And we offer $40 off any repair over $200, no trip charge inside the county, a free second opinion on any written estimate, and a permanent 10% discount for seniors and veterans. Call (877) 610-2993 for an exact quote.
We Also Serve Cities Near Roswell
Our Gate Access Control in Roswell crew regularly runs jobs in Alpharetta, Johns Creek, Milton, and Sandy Springs. If you’re just outside Roswell city limits, we cover you too. Same live answer, same 90-Day Done Right Promise.
Serving Roswell, GA - Our Local Coverage Area
We’re based in the Roswell area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Access Control in Roswell
Because Roswell’s red clay soil expands dramatically when saturated, shifting post footings and stressing the wire connections at keypad posts, while the humidity seeps into connectors that weren’t sealed for outdoor exposure. Keypads fail here not from the keypad itself but from the ground movement and moisture working on 20-year-old builder wiring. The fix is usually new wire pulled through existing conduit, a sealed keypad, and occasionally re-plumbing the post. Call (877) 610-2993 and we’ll diagnose it over the phone or in person.
Yes, in most cases. The gate itself, if it’s ornamental iron from the 1990s, is usually worth keeping. We replace the control board with a modern smart-access board, add a cellular or Wi-Fi module, and rewire the power run if it was undersized originally. In Horseshoe Bend, we replaced a LiftMaster operator on a 1998 wrought iron swing gate where the original builder had run only 18-gauge thermostat wire to the keypad post, causing intermittent keypad failures during humid summers. Our crew pulled a new direct-burial CAT6 and 14/2 power run through the same conduit, replaced the loop detector that had corroded from years of clay moisture, and set the gate to close on a safety photocell that had never been installed. The homeowner now opens the gate from a phone app instead of the original garage-door-style remote.
Any gate operator installed or significantly modified after UL 325 became mandatory must include entrapment protection, which means safety photocells, contact edges, or both. Many Roswell gates built in the 1980s and 1990s never had these installed. When we upgrade your access control, we bring the gate up to current standard, not just patch the keypad. That’s part of the job, not an add-on. Call (877) 610-2993 for a free estimate.
Loop detectors in river-facing neighborhoods west of Azalea Drive do corrode faster than those in upland Roswell subdivisions because ambient humidity near the river accelerates moisture intrusion into detector enclosures. When a loop detector fails, the gate won’t recognize a vehicle waiting to exit or enter, so the remote seems dead even though the operator board is fine. We replace the loop, reseal the enclosure, and test the whole cycle before we leave.
Yes. We add a gate operator, keypad, and all wiring and conduit to a manual gate. Many Roswell homeowners with original 1980s and 1990s iron gates want automation now but assume it’s impossible without a complete gate replacement. It’s not. We weld operator brackets on site, trench the power run, install the operator, keypad, and safety edges, and set the whole system to work from a remote or phone. A full automation retrofit on an existing manual iron gate in Roswell typically runs $2,500-$4,500 depending on gate size, power availability, and operator type.
Call Gatewood Fence & Gate for Gate Access Control in Roswell
If your gate won’t open, your keypad is dead after the last rain, or you’re tired of a manual gate on a busy Roswell street, call (877) 610-2993. Hal answers the phone day or night. The price is quoted before we start, the work carries the 90-Day Done Right Promise, and the name on the shop is the name on the invoice.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Roswell since 2001.