Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Milton, GA
Gate repair in Milton, GA typically runs $145 to $380 for most hinge, post, and alignment work, with full operator replacement landing between $400 and $1,100 depending on the brand and gate weight. Milton’s gates are different from what you’ll find ten miles south: they’re wider, heavier, and built around horse trailers and long private drives. If your gate is sagging, grinding, or refusing to move, call (877) 610-2993 and a live person will answer.
Why Milton Homes Are Different
Milton sits on Georgia red clay, and that clay never stops moving. It swells through wet winters and shrinks during dry summers, which pushes gate posts out of plumb year after year. A brick pilaster that was dead level in May can lean enough by October that your swing gate drags on the latch side. We see this constantly on the custom stone and brick columns built with mid-2000s and newer homes, especially along the equestrian lots where an 800-pound leaf has been hanging off the same hinge for 15 years.
Then there’s the ice. Milton’s slightly higher elevation in North Fulton catches ice storms that Atlanta proper often misses. Frozen worm-drive operators seize, decorative stone caps crack, and water finds its way into motor housings. When that happens, the operator isn’t the only thing that needs attention. We check the column, the post, and the leaf together, because fixing the motor without checking the post means you’ll fix it twice. And on Milton’s equestrian properties, there’s usually a second gate involved: the wide vehicle gate for trailers plus a separate pedestrian gate. Companies that only test the main operator routinely miss the secondary gate’s failing mechanism until it strands someone.
Gate Repair in Milton
Gate repair in Milton means working on 16 to 20 foot estate gates that clear horse trailers, not 10-foot subdivision gates. The weight and span change everything: hinge wear accelerates, operators run hot, and posts take a structural pounding that lighter gates never dish out. We come out, find what actually broke, and repair it on site. Most Milton calls get a same-day visit, and you’ll talk to a live person when you call, not a phone tree. This is the work we do every week across the 30004 zip code.
Hinge & Post Repair
A gate sags in the hinge post, not in the middle. Milton’s red clay swells and shrinks with every wet and dry cycle, and once a post leans even a quarter inch, the gate starts dragging. We dig out, reset, and resquare the post, then weld the hinge assembly back so it stays put through next spring’s rains. A typical hinge and post repair in Milton runs $195 to $340 per post, depending on whether we’re resetting in concrete or repairing the weld in place. If your gate rubs the ground or the latch won’t line up anymore, that’s usually the post telling you something.
Electric Gate Repair
Milton’s electric gates pull hard duty. Many of them cycle six to ten times a day for horse trailers, feed trucks, and farm equipment, not just the family SUV. We service nine major brands including Linear, Viking, Ghost Controls, and DoorKing, and we stock common boards, receivers, and limit switches so we can often finish the job in one visit. Electric gate repair jobs like a bad receiver board or a failed limit switch run $175 to $425. If your gate moves a few inches and stops, or the keypad works but the remote doesn’t, call before you force it, because a stuck operator under load is how gears get stripped.
Automatic Gate Repair
Automatic gates in Milton fail differently than they do in Alpharetta or Roswell. The operators here are often undersized for the leaf weight they’re driving. A 700-pound wrought iron gate on a residential-grade operator will eat through gears and capacitors three times faster than the manufacturer’s wear rating suggests. We check the load every time we touch an opener, and when it’s wrong for the gate, we say so plainly and show you the math before you spend a dime on parts. Most automatic gate repair work runs $175 to $425, and full operator replacement on an estate gate runs $400 to $1,100. For anything beyond repair, our Gate Repair hub covers the full scope of what we fix on site.
Gate Realignment
A gate that closes on its own is a gate telling you something. On Milton’s long driveways, wind load hits a wide gate face harder than it would on a tucked-in city lot. A hairline misalignment at the hinge becomes a two-inch sag at the latch end within months. We realign both leaves, square the frame, and verify the operator’s limits so the motor isn’t fighting the gate. Gate realignment runs $145 to $260, and we cycle the gate ten times in front of you before we leave.
How fast can you get to a gate repair call in Milton?
Most Milton calls are reached the same day, and emergency calls, like a gate stuck open with horses on the property, get prioritized immediately. We’re in Milton weekly, so your address in 30004 isn’t a far-flung trip for us. Call (877) 610-2993 and we’ll give you a straight window, not a four-hour guess.
Do you cover all Milton neighborhoods?
Yes. We service the entire 30004 zip code, from Crabapple and Birmingham Falls to Bethany Bend, Freemanville Road, and the neighborhoods around Birmingham Highway. If you’re on an equestrian estate off Hopewell Road or a newer subdivision near White Columns, that’s our regular territory.
Gate Installation in Milton
A new driveway gate in Milton runs $4,800 to $18,500 for most estate properties, depending on width, material, and operator type. The single largest cost driver here is span: Milton’s equestrian lots routinely need 16 to 20 foot swing gates that weigh 500 to 1,000-plus pounds per leaf, and undersized operators burn out fast under that load. We plan around Milton’s actual conditions, not a catalog spec sheet. Call (877) 610-2993 for a free on-site measure and a written price before any work starts.
Driveway Gate
Driveway gates in Milton are the front line of the property, and most are custom, heavy, and built to match the house. We install steel, iron, wood, and aluminum driveway gates, always matched to an operator that can handle the leaf weight without straining. A single swing gate in the 12 to 14 foot range runs $4,800 to $8,500 installed. If your gate is going up at the end of a long unpaved run off Birmingham Highway, we’ll talk solar power and battery backup on the first visit, not as an afterthought.
Swing Gate
This is the bread and butter of Milton gate work: 16 to 20 feet wide, 500 to more than 1,000 pounds per leaf, often hung on brick or stone pilasters poured by the original home builder. A double swing gate with custom iron or heavy wood runs $9,000 to $18,500 installed. We set hinge posts deeper than the code-bare minimum and match the operator to the actual leaf weight. A swing gate sags in the hinge post, not in the middle, and that’s where we start.
Pedestrian Gate
Pedestrian gates on Milton estates aren’t decorative extras. They’re the gate the horse handler uses twice a day, the one that gets slammed by wind, and the one that gets forgotten when a fence contractor installs the vehicle gate and calls it a day. A standard 4-foot pedestrian gate runs $900 to $2,200 installed. We install standalone walk gates and inspect them whenever we’re on property, because a broken latch on a walk gate is how a horse ends up on Birmingham Road.
Sliding Gate
Sliding gates make sense on Milton properties where a swing gate would eat too much driveway space or fight the grade. We install cantilever and track-style sliding gates with operators that hold up to the grit and pollen we get out here. A steel-frame sliding gate in the 15 to 20 foot range runs $6,500 to $12,000 installed. The worst enemy of a sliding gate in North Fulton is a clogged track and a motor running against resistance, so we set these with clean drainage and accessible service points. See the full scope of what we build on our Gate Installation page.
Do Milton equestrian properties need a wider gate for horse trailers?
Most Milton equestrian driveways need a 16 to 20 foot gate opening to clear a standard gooseneck trailer with a wide turn radius. A 12 foot gate technically passes a trailer straight-on, but leaves zero margin for angle approach. We recommend a minimum 16 foot clear opening for any Milton property with regular trailer traffic.
Can you install a gate opener where there’s no electrical service at the driveway?
Yes. We install solar-powered gate openers on Milton properties where running mains power would mean trenching hundreds of feet through red clay. A properly sized solar kit includes a panel, deep-cycle battery, charge regulator, and an operator chosen for battery duty. Solar adds $800 to $1,500 over a wired operator.
Gate Motor & Opener in Milton
Gate motor and opener work in Milton means dealing with acre-plus lots, long private drives, 16 to 20 foot swing gates built for horse trailers, and red clay that moves more than most people realize. We’ve been called to enough equestrian estates off Freemanville Road and Birmingham Highway to know exactly what happens when an undersized motor meets a 600-pound gate leaf. We fix it the same week you call, and a live person answers the phone around the clock.
Motor Installation
Installing a gate motor in Milton rarely starts with the motor itself. It starts with the post, the gate’s weight, and the swing arc. On the large-lot estates along Freemanville Road and Hopewell Road, we routinely install heavy-duty operators sized for 16 to 20 foot custom iron or wood gates. A typical motor installation in Milton runs $1,800 to $4,200 depending on gate weight, post condition, and whether we’re running new electrical. Every quote is written down and agreed to before we touch a tool.
Motor Repair
Most motor repairs in Milton are either a control board fault, a limit switch gone out of adjustment, or a motor burned out from pushing a gate that a shifting post has bound up. We repair what can be repaired: a stripped gear gets replaced, a rebuildable board gets rebuilt. That repair-first mindset keeps a $400 fix from turning into a $3,000 replacement. Most Milton motor repairs run $280 to $900, and there’s $40 off any repair over $200.
Slide Motor
Cantilever and chain-driven slide gates work on tighter entrances and long runs along Birmingham Highway where a swing gate would smack a car waiting to turn. The motor itself is usually not the first failure point; it’s the chain tension, the guide rollers, or a bent track from a trailer clipping it. Slide motor troubleshooting and repair in Milton runs $250 to $950, depending on whether we’re realigning the track or replacing a control board. For the full operator picture, see Gate Motor & Opener.
Why does my swing gate operator keep erroring after heavy rain?
Because Milton’s red clay swells when it soaks, shifting the gate post and pushing the swing arc out of alignment. The motor senses the added resistance and faults out on overcurrent. The fix is almost never a new motor; it’s correcting the post and re-leveling the hinge line. Call (877) 610-2993 for an estimate.
Do you service both the vehicle gate and the separate horse-handler gate?
We service both on the same visit. Milton’s equestrian estates often run a wide vehicle gate plus a smaller pedestrian or handler gate, and the smaller one fails just as often. One trip, both gates working. Call (877) 610-2993 and we’ll schedule it as a single visit.
Gate Access Control in Milton
Gate access control in Milton means estate-scale entry systems that have to work every single time, not a standard driveway keypad on a quarter-acre lot. A keypad that fails on a cold January morning keeps the farrier waiting at the road while your horse stands in the barn aisle. We install and repair keypads, phone entry, video intercoms, and smart access on Milton’s long private drives and equestrian properties, and we wire them to match the operator they’re controlling.
Keypad Entry
Keypads in Milton take a beating from weather and sunlight, but the bigger issue we see is installation quality on the original build. A keypad mounted on a brick pilaster without a proper weather seal corrodes from the inside. A keypad replacement or repair in Milton runs $250 to $450. If you want a second keypad at the pedestrian gate so the barn manager can come and go without driving through the main gate, we’ll run the wiring and tie both into the same access codes.
Phone Entry
Phone entry systems are the standard on Milton’s larger estates. You want the gate to call your cell when the feed truck arrives, not buzz an intercom nobody can hear from the barn. Adding a phone entry system to an existing gate runs $600 to $1,200, depending on whether we’re pulling new wire from the house. When an existing panel fails, we check the wiring, power supply, and relay before recommending replacement. Details on the full range of entry systems live on our Gate Access Control page.
Video Intercom
Video intercoms are where Milton’s expectations run highest. Homeowners here want to see who’s at the gate, talk to them, and open the gate from a phone app. A video intercom installation starts around $900 to $1,800 for a quality unit with night vision and phone app access. If your current video intercom drops offline every time the temperature swings, the problem is usually the power supply or a corroded connector at the gate post.
Does my automatic gate meet entrapment protection requirements in Milton?
Automatic gates must have safety photocells or contact edges that stop and reverse the gate when something is in the path. Many older Milton gates were installed before current standards, or their safety devices were disconnected because they kept triggering. We check your gate against current entrapment protection requirements and bring it into compliance. Call (877) 610-2993 to schedule a check.
Can a standard gate company fix my double-gate horse trailer setup?
Most can’t, not on the first visit. A double-gate setup means two operators, two sets of safety photocells, loop detectors, and a shared access control system that has to trigger both gates. We service paired operators and integrated entry systems on the same trip, and we check the secondary gate’s mechanism every time.
Gate Parts & Welding in Milton
Gate parts and welding on Milton’s estate gates means accounting for weight, span, and Georgia red clay. We weld on site so your gate stays in your driveway, and we stock the parts that actually hold up on 500 to 1,000 pound leaves. When a custom iron gate cracks at the weld point or a hinge post gives way, Hal welds it in place, tests it, and shows you the work before we leave.
Hinge Replacement
On Milton’s estate gates, hinge failure is usually a symptom of post movement. The red clay under the footing swells in wet seasons and shrinks in dry ones, and a 500 to 1,000 pound leaf slowly levers the hinge bolts loose or bends the hinge itself. Hinge replacement on a standard estate swing gate in Milton runs $280 to $650 per leaf, depending on the hinge type and whether we’re welding or bolting through. A new hinge on a shifting post is a half-fix, and we don’t do half-fixes.
Post Replacement
This is the big one in Milton. When an undersized post or a shallow footing gives way, the whole gate drops. We cut out the old post down to undisturbed soil, pour a reinforced footing sized for the gate span and soil conditions, and set a new steel post. Post replacement runs $900 to $1,800 for a single steel post with a reinforced footing, more if the gate has to be fully removed and re-hung. In Milton’s clay, we pour footings below the shrink-swell zone so the post stops moving with the seasons.
Rail Repair & Custom Welding
Wrought iron rails crack at the weld points, especially where a heavy leaf flexes against a hinge or where a vehicle tapped the gate. We cut out the cracked section and weld in fresh steel, then grind it clean so the repair disappears into the original design. Rail and panel welding repairs usually run $180 to $480 per repair point, and custom fabrication is quoted at $95 to $135 per hour plus materials. The full breakdown is on our Gate Parts & Welding page.
Can you weld a cracked wrought iron gate panel without removing it from the post?
Yes, in most cases we can weld the crack while the gate stays on its hinges, as long as the gate is properly blocked and stable. We grind out the crack, weld in fresh steel, and grind it smooth. If the crack is near a hinge and the gate is still under load, we may need to take the tension off that corner first.
Why do my Milton swing gate hinges wear out faster than gates in Alpharetta?
Because your gate is likely twice as heavy and twice as wide. Milton’s acre-plus lots and equestrian culture mean most gates are 16 to 20 feet wide to clear horse trailers. That extra span multiplies the leverage on the hinge post, especially when red clay shifts the footing. The hinge wears faster because it’s carrying a structural load it was never sized for.
Brands We Service in Milton
We service nine major gate brands in Milton, including Linear, Viking, Ghost Controls, and DoorKing. We stock common boards, receivers, limit switches, and remotes for these brands locally, which means many Milton repairs finish in a single visit instead of waiting on a parts shipment. See the full list on our brands page.
Pricing for Gate Repair in Milton, GA
| Service | Typical range in Milton |
|---|---|
| Gate realignment | $145 - $260 |
| Hinge & post repair | $195 - $340 per post |
| Electric gate repair | $175 - $425 |
| Operator replacement (estate gate) | $400 - $1,100 |
| Motor repair | $280 - $900 |
| Motor installation | $1,800 - $4,200 |
| Hinge replacement | $280 - $650 per leaf |
| Post replacement | $900 - $1,800 |
| Rail & panel welding | $180 - $480 per point |
| Keypad repair/replacement | $250 - $450 |
| Video intercom installation | $900 - $1,800 |
What pushes a Milton price up is gate weight and span: a 20-foot double swing gate with 1,000-pound leaves costs more to repair than a 12-foot single. Every price is quoted and agreed before any work starts. You will not get a surprise invoice at the door.
Neighborhoods We Serve in Milton
We work all over Milton’s 30004 zip code, from the equestrian estates in the northwest to the subdivisions around Crabapple. Typical response time across the city is same-day for repair calls, and we’re in these areas weekly:
- Crabapple
- Birmingham Road / Freemanville corridor
- Bethany Bend and Birmingham Falls
- Hopewell Road and Cogburn Road estates
- North Valley horse country
Service Area - Cities Near Milton
We keep crews rolling across North Fulton and the surrounding counties. If you’re near Milton but not inside the 30004 zip code, we likely cover you too: Milton, GA is our home base for this page, but we also serve Alpharetta, GA, Roswell, GA, Johns Creek, GA, Peachtree Corners, GA, and Holly Springs, GA. If you’re not sure whether we cover your address, call (877) 610-2993 and a live person will tell you straight.
Serving Milton, GA - Our Local Coverage Area
Gatewood Fence & Gate crews serve Milton and the communities around it; dispatch is coordinated from our Atlanta office. The map shows the Milton coverage area; if your address is on it, we can help.
Also serving nearby: Milton, GA, Alpharetta, GA, Roswell, GA, Johns Creek, GA, Peachtree Corners, GA, Holly Springs, GA.
FAQs About Gate Repair in Milton
Most Milton repair calls get a same-day visit. Emergency calls, like a gate stuck open with horses on the property or a stuck-closed gate on your only driveway, get prioritized immediately. We’re in Milton weekly, so the 30004 zip code is regular territory, not a far-flung dispatch. Call (877) 610-2993 for a straight window.
Many Milton neighborhoods with custom estate entrances have HOA design guidelines for gates, columns, and operators. We’re familiar with the common requirements and can provide the spec details your HOA asks for. The gate itself is your property; the approval process is usually about appearance and setback, not the repair itself. We’ll help with the paperwork where we can.
Yes. Milton’s double-gate setups mean two operators, two sets of safety photocells, and often a shared access system. We diagnose both gates on the same visit and repair what’s actually failed on each, so you’re not paying for a second trip when the other gate fails a week later. Call (877) 610-2993 and we’ll schedule the full property.
If your gate is sagging, stuck, or dead in Milton, call (877) 610-2993 now. Hal or a member of his crew will answer, give you a straight window, and quote the price before any work starts. Free estimates, no trip charge inside the county, and every job backed by the 90-Day Done Right Promise in writing.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Milton Customers Say
"He builds the gates himself in his own shop. You can go and look at it. That is not something you can say about the outfits that just order a panel in."
- Doreen Whitfield"Welded the hinge back onto our wrought iron gate on site rather than taking it away for a fortnight. Ground it back and painted it and you cannot see the repair."
- Winston Achterberg"Fitted a keypad and an intercom so my mother can let carers in without coming down the drive. He set it up and then made her practise with it until she was comfortable."
- Lucinda Marchbanks