Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Fort Lupton, CO
If your gate is sagging, refusing to open, or hanging off a hinge post in Fort Lupton, you want someone who knows the difference between a quick latch adjustment and a footing that’s been wrecked by three winters of Weld County frost heave. We’re Gatewood Fence & Gate, and Hal Gatewood has been welding, aligning, and rebuilding gates in this part of Colorado long enough to know exactly what the wind and the irrigation overspray do to steel out here. Call (877) 610-2993 and a live person picks up, day or night. We’ll get someone on the road to you quickly with a straight price before any work begins.
Why Fort Lupton Homes Are Different
Fort Lupton sits in the wide-open flats of Weld County where the Front Range wind doesn’t slow down until it hits a fence line. A 50 mph gust puts enormous lateral stress on a gate frame, and if the hinge post wasn’t set deep or welded square, that gate starts sagging within a season or two. We see it constantly on exposed acreage properties around 80621 that lack windbreaks.
The freeze-thaw cycle is harder out here too. Without Denver’s urban heat island, Fort Lupton’s soil heaves more dramatically in winter, which knocks gate posts out of plumb and leaves the latch misaligned come spring. Add in the irrigation overspray from surrounding farm operations and those aging steel tube gates on decades-old post-and-rail lines develop rust at the hinges and latch hardware that a suburban ornamental gate never faces.
And then there’s the oil and gas work. Fort Lupton sits at the heart of Weld County’s DJ Basin production zone, meaning gate repair technicians here regularly service security access gates at active well pads, pipeline easements, and industrial compounds. Paired with the surrounding feedlot and irrigated farm operations, the typical Fort Lupton gate job involves heavy-duty welded-pipe or livestock-rated agricultural hardware far more than a standard residential ornamental gate.
Gate Repair in Fort Lupton
Gate repair in Fort Lupton usually means one of two things: a residential driveway gate that stopped opening, or a commercial gate at an agricultural or oilfield site that can’t go down because work stops with it. Most jobs run $180 to $850 depending on whether we’re rebuilding a hinge post, replacing a control board, or welding a cracked frame. A live person answers when you call Gatewood Fence & Gate, and the person who shows up will be someone who knows how to read a gate frame and tell you whether it can be saved.
Electric Gate Repair
In Fort Lupton, electric gate repair usually starts with an operator that’s been mounted on a well pad or acreage entrance for ten or fifteen years. We service LiftMaster, Viking, DoorKing, Ghost Controls, Elite, and the other major brands, and we keep common control boards, sensors, and receivers stocked locally so turnaround is fast. A lot of what we fix are operators with obsolete boards that can’t accept modern UL 325 entrapment sensors. Sometimes you retrofit for $180-$380. Sometimes the board is so far behind code that a full operator swap at $650-$1,400 is the only compliant path. We’ll tell you which before we touch a wire.
Hinge & Post Repair
The gate sags in the hinge post, not in the middle. That’s a Hal-ism, and it’s true on every Fort Lupton property from an in-town 1975 ranch lot to a forty-acre parcel off Weld County Road 6. Frost heave lifts post footings every winter, and by spring the gate is dragging and the latch won’t line up. We dig down, re-set the post deeper, re-plumb it, and weld or shim the hinges back to true. A single hinge and post re-set in Fort Lupton typically runs $250-$450. Fix the panel without the post and you’ll fix it twice.
Weld & Rust Repair
Fort Lupton has more welded pipe and steel tube gates than any suburb south of here. Feedlot runoff and irrigation overspray eat the weld points first, and when a weld lets go it usually lets go at the hinge post. We repair welds on site, in the driveway or at the pasture entrance, so the gate stays where it is. No hauling it off to a shop. Weld repair runs $80-$150 per weld point. For a rusted-through post or a frame that’s gone past structural, we’ll be straight with you: sometimes replacement is the cheaper answer. We’re not in the business of welding good money onto bad steel.
We handle the full range of Gate Repair work in Fort Lupton, from wind-stressed slide gates on exposed acreage to frost-heaved posts on irrigated lots that need resetting every spring.
Can you retrofit an old swing gate operator to meet current UL 325 entrapment protection requirements?
Sometimes yes, sometimes no, and a company that tells you otherwise is guessing. If the existing operator has a functional motor and gearbox and can accept retrofit edge sensors or photo eyes, we can often wire the protection in and get the gate compliant without a full replacement. If the control board itself can’t read the newer sensor inputs, the board has to go. We’ll test and tell you before we quote. Call (877) 610-2993 for an exact quote - estimates are free.
Why do my gate posts keep going out of plumb every spring on my acreage near Fort Lupton?
Frost heave. Every winter, moisture in the soil around your post footings freezes and expands, pushing the footing upward or sideways. When the ground thaws in March, the gate suddenly doesn’t latch and the opener strains. Irrigated pasture or lawn ground makes it worse because there’s more water in the soil profile. The fix is re-setting the post deeper with a wider concrete collar. Call (877) 610-2993 and we’ll come look at it.
Gate Installation in Fort Lupton
A heavy gate on a 16-foot opening takes a serious operator and posts set deep enough to hold it. In Fort Lupton, the wind, the frost, and the distance between power poles decide most of what we spec on a job. We’ve been welding and installing gates on Weld County acreages since 2001, and we answer the phone around the clock at (877) 610-2993.
Driveway Gate Installation
Long driveways off Weld County roads call for operators with real torque, not a box-store kit. We’ll spec the opener for the actual gate weight and wind load across the face, not the optimistic number on the box. A single driveway swing gate in Fort Lupton typically runs $1,800 to $3,500 installed, depending on width and whether we’re setting new posts. Solar is frequently the right answer out here, and we stock the panels, batteries, and brackets to do it right. Solar power adds $500 to $1,200 over a standard AC opener.
Sliding Gate Installation
Sliding gates earn their keep on industrial lots and well pad entrances where a swing gate would need too much clear space. We install cantilever and V-track slides, with the appropriate safety edges and photo-eyes for whatever the site requires. Oil and gas operators often need locked anti-ram barriers or coded entry. That’s work we take on regularly. A sliding gate for industrial or well pad access runs $4,500 to $7,500, plus access control hardware like keypads or card readers at $600 to $2,200 depending on the system.
Security Gate Installation
Security gates for Fort Lupton well pads and pipeline easements have to meet operator security standards, not just keep cattle in. We install gates with coded entry, anti-tailgate hardware, and heavy-duty frames built from welded steel or pipe. The same crew that welds a ranch gate can wire a DoorKing keypad to a Viking operator and make it work right. A double swing gate for a 16-foot opening runs $3,200 to $5,800 with posts set 4 feet deep and heavy-duty welded hinges.
We measure, quote, and schedule every Gate Installation - no same-day installation promises, because this work is measured, ordered, and built to last.
Are solar gate openers reliable on a Fort Lupton acreage where the nearest power pole is hundreds of feet away?
Yes. We install Viking and Ghost Controls solar openers on remote Fort Lupton properties regularly, and they hold up as well as a hardwired unit when the panel sizing and battery capacity are done correctly. The key is a 10-watt or larger panel mounted with clear southern exposure, plus a deep-cycle battery sized for the gate’s daily cycle count, not the bare minimum. Call (877) 610-2993 for a free measure and written quote.
How deep do gate hinge posts need to be in Fort Lupton to survive the frost heave?
Four feet, minimum, for any gate wider than 10 feet. The freeze-thaw cycle in this area is more aggressive than in Denver because there’s no urban heat island holding ground temperatures steady. We set hinge posts 4 feet deep in concrete on acreage jobs, and sometimes deeper on corner or pull posts that carry extra wind load. At that depth, the post anchor sits below the active frost line and stops the seasonal heave that ruins shallow footings.
Gate Motor & Opener in Fort Lupton
Gate motor and opener work in Fort Lupton usually involves either a dead opener on a driveway gate that won’t budge, or a heavy farm or well-pad gate that’s torn itself apart in the wind. A basic motor repair on a residential swing gate in Fort Lupton typically runs $225 to $420, while a full operator replacement for a wide acreage or commercial gate lands between $1,400 and $3,800 depending on the span and power source.
Motor Repair and Troubleshooting
Most Fort Lupton repair calls come down to one of three things: a motor burned out because the gate is binding, a control board fried by a power surge, or limit switches that drifted out of adjustment. We diagnose on site, quote the repair before any work starts, and carry common parts for all the brands we service. Replacing a control board is usually $350 to $650. If the gate post has shifted and the motor is fighting the geometry, we’ll fix the post, not just swap the motor and hope.
Linear Motor Service
Linear arms are the workhorse on wide Fort Lupton swing gates. They push and pull rather than relying on a gear and chain, which makes them better suited to the long, heavy pipe gates around feedlots and well pads. We rebuild and replace linear motor assemblies, correct arm geometry, and service the Viking and DoorKing linear operators we see most often on Weld County acreage. A full operator swap on a standard single-family gate lands between $1,200 and $2,100 installed.
Slide Motor and Rack Repair
Slide gates take a beating out here. The flat, open terrain funnels wind that pushes against the gate panel and loads the rollers, rack, and pinion constantly. A gust over 50 mph will flex a wide gate and knock the rack out of alignment with the pinion gear, and then the motor overheats trying to move a gate that’s fighting it. We replace bent rack sections, rebuild roller carriages, and re-shim the operator so the gate runs square. A heavy-duty linear or slide operator for a wide farm or security gate runs $2,000 to $3,800 depending on the span, power source, and whether we need to add battery backup or solar.
We service every major brand through our Gate Motor & Opener program, with parts stocked locally for fast turnaround on Fort Lupton calls.
Why did my heavy pipe gate sag and burn out the opener motor after only two years here?
Because the post moved, not the gate. Fort Lupton’s freeze-thaw cycles heave the ground and knock hinge posts out of plumb. Once the post shifts, the gate binds, the motor overdraws, and it burns out fast. The fix is resetting the post in a deeper concrete pier, then re-hanging the gate and re-setting the operator limits. Call (877) 610-2993 - we’ll diagnose it properly.
Do you install solar-powered gate operators for rural Fort Lupton properties without grid power at the entrance?
Yes. We install solar-powered gate operators on rural Fort Lupton properties where running mains power to the entrance isn’t practical or affordable. Most of these are on acreage east and north of town where the nearest breaker is hundreds of feet away. We size the panel and battery bank for the gate weight and the number of cycles per day, and we add a properly rated charge controller so the battery stays healthy. Call (877) 610-2993 for an exact quote.
Gate Access Control in Fort Lupton
Gate access control in Fort Lupton means keypads, card readers, phone entry, and intercoms built for wind, frost heave, and working ranch and oilfield gates. If your gate won’t open, your keypad’s dead, or you need coded entry on a well pad, we fix it without making you replace hardware that still has life in it. Hal Gatewood’s crew knows Fort Lupton’s gate jobs because we do them, not because we read about them in a training manual.
Keypad Entry
Keypads are the most common access control request we handle in Fort Lupton, and the most common failure we repair. Irrigation overspray on farm and feedlot properties accelerates corrosion on keypad housings and internal contacts. A keypad that works intermittently is almost always a corroded connection or a failing membrane, not a reason to replace the entire gate operator. We test, clean, and rebuild before we ever talk replacement. A new keypad entry system in Fort Lupton typically runs $450 to $900 installed, depending on whether it ties into an existing operator or needs a full setup.
Phone Entry
Phone entry systems let you buzz a gate open from a cell phone or landline, which matters when you have drivers, delivery trucks, or field workers who shouldn’t carry a remote. On Fort Lupton acreage and industrial sites, we install phone entry modules that tie into existing gate operators and work through cellular or landline connections. A phone entry add-on typically runs $600 to $1,200 in Fort Lupton, depending on whether you need cellular hardware or can use an existing landline.
Card Reader Systems
Card readers show up mostly on Fort Lupton’s commercial and oilfield sites, where multiple people need controlled access without sharing a single code. We install and repair proximity card readers, key fob systems, and tie them into existing operators from Linear and DoorKing. A single-door card reader system in Fort Lupton runs $800 to $1,800 installed, with per-card or per-fob costs around $5 to $15 each. We also handle the maintenance issue most installers ignore: grounding. Weld County’s dry air and frequent electrical storms mean poor grounding kills card readers that should have lasted years.
We wire, program, and maintain Gate Access Control systems for everything from rural residential driveways to active well pads with operator-mandated security standards.
Can you convert an existing Fort Lupton oil well pad pipe gate to coded entry without replacing the whole gate?
Yes, in almost every case. We reinforce the existing gate frame, check the post depth and plumb, then install a keypad, operator, and required entrapment protection. You don’t need a new gate just because the old one was never automated. We’ve done this conversion on well pads throughout northern Weld County, and the oil and gas operators we work with appreciate not paying for steel they don’t need. Call (877) 610-2993 for a free assessment.
How do you fix a keypad entry that works inconsistently on a Fort Lupton farm gate?
Inconsistent keypad performance is almost always a corrosion or wiring problem, not a reason to replace the whole system. On Fort Lupton farm properties, irrigation overspray accelerates rust on keypad contacts and housings. We test the keypad circuit, check the wiring run for breaks or bad splices, and clean or replace the housing with one sealed for agricultural exposure. Most keypad repairs run $150 to $400, far less than replacing a working operator. Call (877) 610-2993 and we’ll sort it out.
Gate Parts & Welding in Fort Lupton
Gate parts and welding in Fort Lupton usually comes down to one question: can the gate be saved, or does the whole thing need to come out? Hal Gatewood will tell you the same thing he’s told folks since 2001: fix the post, weld the rail, and salvage the steel before you spend money on a new gate. Our crew handles hinge replacement, post reset, custom welding, and operator work across Fort Lupton, from in-town lots to acreage parcels off Weld County Road 8.
Hinge Replacement
A sagging gate in Fort Lupton is almost never a weak panel. It’s a hinge that has pulled loose, rusted through, or sheared at the weld. On the in-town pre-1980 homes near the Fort Lupton Recreation Center, we see barrel hinges that have been soaking in sprinkler overspray for thirty years. Hal cuts the old hinge off, dresses the post face, and welds a fresh heavy-duty hinge at the correct height. Hinge replacement on a residential swing gate typically runs $180 to $340 per hinge, depending on the steel weight and whether we need to weld a reinforcement plate.
Post Replacement
Frost heave is the quiet killer of gate posts in Weld County. Fort Lupton sits out where the freeze-thaw cycle does not get softened by the Denver heat island. A post set in a shallow footing will lift a half-inch every winter and settle crooked every spring. Eventually the slide gate binds on its rollers or the swing gate scrapes the driveway. We dig out the old footing, set the new post in at least a 36-inch concrete pier with rebar, and brace it plumb while the concrete cures. Post replacement, including digging out the old footing and pouring the pier, runs $450 to $900 per post.
Custom Welding
Not every gate problem has a part waiting on a shelf. Fort Lupton’s mix of oil field security gates, livestock corrals, and aging farm gates means a lot of what we do is built to fit the site. We weld custom hinge brackets, extend gate leaves, box in damaged posts, add drop rods, and fabricate heavy-wall pipe gates when the existing gate has outlived its frame. Most farm gate latch and hinge welding in the Fort Lupton area lands between $150 and $500. On agricultural properties east of town where the gate has to hold back a bull or a loaded grain truck, we weld livestock-rated hardware that won’t shear under load.
We do our Gate Parts & Welding on site, in your driveway or at your pasture entrance, so the gate stays where it belongs.
Can you weld a new hinge pin onto a rusted pipe gate at a Fort Lupton feedlot without replacing the whole post?
Yes, in most cases we can weld a new hinge pin to a rusted pipe gate without replacing the post, as long as the post itself is still structurally sound. We cut the old pin flush, grind the surface clean, and weld on a new pin with a reinforced base plate. If the post has thinned from rust through too much of its wall, we’ll sleeve it or replace it and tell you why. Call (877) 610-2993 for an exact quote.
How do you keep a slide gate working on a Fort Lupton acreage when the ground heaves every spring?
The answer is a deeper footing and an adjustable track system. Frost heave in Weld County lifts shallow footings every winter, and a slide gate on rollers binds hard when the track moves. We set posts at least 36 inches deep with rebar and drainage stone, and we shim or adjust the track in the spring if the ground settles unevenly. A gate that’s set deep and watched seasonally won’t give you the same headache every March.
Brands We Service in Fort Lupton
We carry parts and service manuals for nine major brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Most common control boards, sensors, and receiver modules are stocked locally, which means we don’t order your part from a warehouse three states away and make you wait. For our brands page with full details on each line, click through.
Pricing for Gate Repair in Fort Lupton, CO
| Service | Typical Range in Fort Lupton |
|---|---|
| Latch adjustment or minor alignment | $95-$175 |
| Weld repair (per weld point) | $80-$150 |
| Electric operator control board swap | $180-$380 |
| Chain & track realignment | $150-$300 |
| Motor repair, residential swing gate | $225-$420 |
| Hinge replacement (per hinge) | $180-$340 |
| Hinge & post re-set (single post) | $250-$450 |
| Post replacement with concrete pier | $450-$900 |
| Rail repair and splicing | $200-$600 |
| Full operator replacement (parts & labor) | $650-$1,400 |
| Heavy-duty operator, farm/security gate | $2,000-$3,800 |
| Keypad entry installation | $450-$900 |
What pushes price up in Fort Lupton: deep frost lines requiring longer post footings, wind-rated hardware for exposed acreage, solar power systems where grid access is distant, and access control integration for oilfield security standards. Every price is quoted and agreed before any work starts, and that number does not change at the door. We also take $40 off any repair over $200, and seniors and veterans get a permanent 10% discount.
Neighborhoods We Serve in Fort Lupton
We work across the whole 80621 area, from the in-town neighborhoods south of Highway 52 to the rural acreage parcels that fan out north and east. Typical response time inside Fort Lupton is same day for repair calls, and emergency gate failures get priority when you call. We schedule measured installation and access control work for the next available opening.
- Highview Estates
- Aristocrat Ranchettes
- Downtown Fort Lupton (Denver Avenue corridor)
- Acreage parcels along Weld County Road 6 and CR 8
Service Area - Cities Near Fort Lupton
We run trucks throughout northern Weld County and the surrounding communities. If you’re near Fort Lupton, CO, Frederick, CO, Firestone, CO, Brighton, CO, Lochbuie, CO, or Erie, CO, we can get to you. Dispatch and scheduling are coordinated from our Denver office; crews serve Fort Lupton locally with no trip charge inside the county.
Serving Fort Lupton, CO - Our Local Coverage Area
Gatewood Fence & Gate crews serve Fort Lupton and the communities around it; dispatch is coordinated from our Denver office. The map shows the Fort Lupton coverage area; if your address is on it, we can help.
Also serving nearby: Fort Lupton, CO, Frederick, CO, Firestone, CO, Brighton, CO, Lochbuie, CO, Erie, CO.
FAQs About Gate Repair in Fort Lupton
Weld County requires permits for most new gate installations, especially if you’re adding an automated operator or changing the driveway access point. Fort Lupton’s in-town properties may have additional setback rules through the city. We know the local requirements and can walk you through them during the free estimate. Call (877) 610-2993 and we’ll sort out what applies to your property.
For repair calls, yes. A live person answers our phone 24 hours a day, and emergency gate failures - a gate stuck open, a motor burned out, a security gate that won’t lock - get priority dispatch. Same-day response is typical inside Fort Lupton. Installation and access control work is scheduled by measurement and availability, not rushed. Call (877) 610-2993 and we’ll get you on the board.
Yes. The flat, open terrain of Weld County funnels Front Range gusts that routinely exceed 50 mph. A wide gate face catches that wind like a sail, loading the hinges, twisting the frame, and stretching chains on slide gates. We’ve replaced hinge welds and re-tracked slide gates on Fort Lupton properties that failed after a single storm. Wind-rated hardware and deeper post footings are not upsells here - they’re necessities.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Fort Lupton Customers Say
"Welded the hinge back onto our wrought iron gate on site rather than taking it away for a fortnight. Ground it back and painted it and you cannot see the repair."
- Winston Achterberg"Fitted a keypad and an intercom so my mother can let carers in without coming down the drive. He set it up and then made her practise with it until she was comfortable."
- Lucinda Marchbanks"Beautiful gate and solid work. The build took about three weeks longer than the estimate because he was waiting on the ironwork, and I would rather have known that at the start than found out along the way."
- Beatrice Nwosu