Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Augusta, KS
Gate repair in Augusta usually breaks into two very different jobs. In town, near the older streets around State Street and Dearborn, it’s ornamental driveway gates on posts that have been sitting in Butler County clay since before most of us were born. On the acreage lots south and east of the city, it’s wide-span steel pipe gates with seized hinges and wind-bent frames. The fix for both starts the same way: figure out what actually failed, then repair it in place instead of hauling it off and quoting a replacement. Call (877) 610-2993, tell us what the gate is doing, and we’ll give you a real answer and a real number.
Why Augusta Homes Are Different
Augusta sits where Butler County’s ranch belt meets a proper small town, and that changes gate work in ways a suburban shop near Wichita rarely sees. The south and southwest winds here, often sustained at 20 to 30 miles per hour, push against gate frames for days at a time, so hinge wear and frame racking show up years earlier than they would in a sheltered subdivision. The clay soil underneath town swells when wet and heaves when it freezes, which works posts out of plumb and cracks concrete footings on a regular cycle. We re-plumb posts and repair footings on nearly every service call we make in Augusta, not once in a while.
The housing stock adds another layer. In-town neighborhoods include oil-boom-era homes from the 1910s through the 1930s, mid-century ranches, and some newer infill. Many of those older gate posts are original, set in concrete that has crumbled at ground level, with hardware corroded by decades of Kansas weather. Out on the ranchette lots, the pipe gates were often installed generations ago with whatever hinge was on hand. Neither one gets fixed by swapping in a new gate panel and calling it done.
Gate Repair in Augusta
Gate repair in Augusta typically runs $150 to $450 for hinge, post, and alignment work. Electric and automatic gate repairs usually land between $225 and $650 depending on the opener, the board, and how much wind damage got done before we arrived. We quote the full number before any work starts, and that’s the number you pay.
We arrive with the truck stocked for the common Augusta failures: hinge barrels, latch assemblies, photo eyes, control boards, and welding gear. Most repairs start within a day or two of your call, and the person who answers the phone is a live person, any hour. For the specifics of what we fix and how we approach it, see our Gate Repair service page.
Electric Gate Repair
Electric gate repair in Augusta usually means a control board that gave up, a photo eye that no longer sees the boundary, or a capacitor that failed after years of south wind slamming the gate against its stops. We test the full circuit before we start swapping parts, because a gate that will not open is often a dead connection, not a dead board. On acreage properties, the freeze-thaw cycles in Butler County’s clay soil wiggle low-voltage wire connections loose, and that’s a failure we fix rather than masking with a new board. Electric repairs in Augusta run $225 to $550 depending on the part and the panel.
Automatic Gate Repair
Automatic gate repair covers swing arms, slide operators, remote receivers, and keypad entry. On windward-facing gates around Augusta, the sustained 20 to 30 mph winds make automation work harder and fail sooner than the same hardware would in a calmer location. We service LiftMaster, FAAC, BFT, and Ghost Controls systems, and we keep common boards and remotes on the truck so we’re not making you wait on a parts shipment. A full automatic opener repair on an Augusta ranchette with a heavy pipe gate can run $325 to $650 when the ram or gearbox has failed.
Hinge and Post Repair
A gate sags in the hinge post, not in the middle, and that’s where we start. Older in-town homes in Augusta, especially the 1910s through 1930s construction, often have posts set in concrete that crumbled decades ago. The freeze-thaw cycle heaves the post, the hinge twists, and the gate starts dragging on the latch side. We dig out the old footing, re-plumb the post, and re-hang the gate so it swings true. Hinge or post repair in Augusta runs $150 to $400 depending on how much concrete work the footing requires.
Gate Realignment
Gate realignment fixes a gate that binds on one side, refuses to latch, or rubs a groove into the driveway. We see it constantly after each spring storm season, when the wind has pushed the frame out of square and the clay soil has done its freeze-thaw heave under the posts. Realignment means adjusting the post plumb, the hinge position, the latch throw, and the picket sag together, because they all affect one another. A typical realignment in Augusta is $125 to $300, and the sooner you catch the drag, the less hinge and frame damage you pay for later.
How fast can you get to Augusta for a gate repair?
We can usually reach Augusta the same day you call. Most hinge, post, and realignment work is completed on the first visit, and electric or automatic repairs are typically same day or next morning depending on the part. Call (877) 610-2993 when the gate fails. A live person answers around the clock and can tell you honestly when we’ll be there.
Do you work on livestock gates and pipe gates on Augusta acreage properties?
Yes, and those are some of our most common Augusta jobs. The big steel pipe gates on the rural-residential lots south and east of town, with their ball-and-socket hinges and wind-bent frames, are a specialty. We weld on site and free seized hinges that other shops won’t touch, and we don’t charge a trip fee inside Butler County.
Gate Installation in Augusta
Gate installation in Augusta runs roughly $900 to $4,800 depending on whether you’re hanging an ornamental driveway gate off Kelly Road or setting a 16-foot steel pipe gate on a ranchette south of town. That’s the range, quoted in writing before the first post hole is dug. Hal Gatewood has been at this since 2001, and the name on the shop belongs to the guy who shows up. For the full scope of what a proper install covers, see our Gate Installation page.
Driveway Gate Installation
Most driveway gates in Augusta fall into two camps. In-town homes want something that looks right and keeps the dog in, usually a single swing gate in ornamental steel or aluminum. The ranchette lots east and south need a different animal: wide-span steel pipe gates built to take wind and livestock. We hang both, and we size the posts and hinges for the actual load, not the brochure. A basic single swing driveway gate in Augusta runs $900 to $1,800 with two new posts and a powder-coat finish.
Swing Gate Installation
Swing gates are the most common style in Augusta, and the most abused by weather. Butler County’s sustained south and southwest winds, the kind that run 20 to 30 mph for days, put constant lateral stress on hinge posts. We install swing gates with reinforced posts and heavy-duty hinges from the start, because re-plumbing a leaned post a year later is money you shouldn’t have to spend. A double swing gate starts around $2,200 and can reach $4,800 with a powder-coated steel frame, full automation, and a keypad.
Sliding Gate Installation
Sliding gates make sense on Augusta properties with short driveways or steep grade changes, where a swing gate would clip a parked car or drag on the apron. We install track and cantilever sliding gates, and we pay close attention to the track bed because Butler County clay holds water. A track that sits in a damp low spot will heave within two winters. Sliding gates run $1,800 to $4,500 installed, with the track bed and drainage work included in that number.
Do you cover all of Augusta and the rural areas around it?
Yes. We work the entire 67010 zip code, from the in-town neighborhoods near State Street and Kelly Avenue out to the acreage lots and ranchettes south and east of town. The rural pipe gates are a regular job for us, and there’s no trip charge anywhere inside Butler County.
What does a typical gate installation in Augusta cost compared to Wichita?
Augusta pricing runs about the same as Wichita for ornamental work, and rural agricultural gates often come in lower because they’re simpler: steel pipe, heavy hinges, no ornamental finish. A large rural pipe gate lands between $1,200 and $3,500. Call (877) 610-2993 for a written quote, agreed before anything starts.
Gate Motor & Opener in Augusta
A gate motor or opener in Augusta usually fails one of two ways: slowly, as wind and clay soil grind the hinges out of alignment over months, or all at once when a spring storm sends a lightning strike through the control board. Either way, you need someone who knows Butler County gates, not just gates in general. We’ve been fixing gate motors and openers since 2001, with a live person answering the phone at any hour. For details on the brands and failure modes we handle, see our Gate Motor & Opener page.
Motor Installation
Installing a new gate motor in Augusta usually starts with the post, not the operator. On the ranchette lots south and east of town, we’ve pulled old posts out of the ground that were set in crumbling concrete with freeze-thaw cycles slowly heaving them out of line. A new Viking or Ghost Controls operator on a post that’s six degrees out of plumb will eat its own gears inside a year. We re-plumb the post, pour a proper footing, and then mount the motor. Full operator replacements start around $950 for a residential swing gate and run up from there for wide, heavy slide gates.
Motor Repair
Motor repair means diagnosing what actually failed, not swapping parts until something works. A seized limit switch, a corroded relay, a gear pulled out of alignment by wind-bent posts: most of these are fixable on site with the truck we bring to your driveway. We weld on the truck bed, not back at a shop, so the gate stays in your yard. A motor repair call in Augusta typically runs $180 to $340 depending on what failed.
Slide Motor
Slide gate motors take a beating from wind. A 16-foot slide panel in a 30 mph southwest wind acts like a sail, and the motor’s limit switch and gearbox absorb all of it. We set up slide motors for the actual panel weight and wind load, not a generic spec off a chart. Because Augusta’s clay soil holds water against the track and rollers, we install drainage and use sealed components. Rebuilding a wind-bent post with new footing concrete and re-hanging the gate lands around $400 to $700.
Why does my Augusta swing gate operator work after a rain but fail during dry spells?
That’s the Butler County clay talking. When the ground is wet, swollen clay supports the hinge post and the gate sits closer to alignment. During dry spells, the clay shrinks, the post shifts, and the operator’s safety edge or limit switch no longer lines up, so the board faults. The fix is re-plumbing the post into a deeper, properly drained footing, not a new motor.
Can you retrofit my older FAAC opener with battery backup in Augusta?
Some older FAAC boards can take a battery backup; most from the 1990s cannot. If the board is compatible, the retrofit runs about $250 to $450 depending on battery capacity. If it isn’t, we’ll give you a straight written price for both the retrofit attempt and a replacement motor. Call (877) 610-2993 and we’ll tell you which camp your board falls in.
Gate Access Control in Augusta
Gate access control in Augusta, KS typically costs $450 to $1,850 for a complete keypad or phone-entry installation, and most jobs wrap up the same day we arrive. We work the full mix here: in-town homes, mid-century neighborhoods, and large acreage properties. A keypad that won’t trigger or a phone-entry box that went dead is usually a wiring fault or a misaligned gate, not the whole system. See our Gate Access Control page for the full scope.
Keypad Entry
Keypad entry is the most requested access control we install in Augusta, both in town and on the acreages. A new outdoor-rated keypad for a typical Augusta driveway gate runs $180 to $450 installed, including wiring to the opener and programming for unique codes. The south and southwest wind carries fine clay dust that works its way into the number pad buttons over time, so we mount and seal new units accordingly.
Phone Entry
Phone entry lets you buzz the gate open from your cell phone or a landline. A complete phone-entry install in Augusta runs $600 to $1,400, and the spread comes down to whether we’re tying into an existing opener or installing a new relay and radio receiver. On larger acreage lots where the gate sits far from the house, we prefer hardwired or long-range radio setups over cellular-only units, because signal dead zones south and east of town are real.
Card Reader
Card readers show up on Augusta properties with multiple drivers: ranch operations, boarding barns, small businesses, families with rental homes on the same parcel. A basic standalone card reader install starts around $400 to $650. We see far fewer card readers than keypads, but the ones we do see are almost always on gates that also have a pedestrian callbox, and the install needs to account for both.
Do you handle the power run and the safety edges as part of an access control install in Augusta?
Yes. A gate access control system is only as good as the power feeding it and the safety edges that stop it from closing on a vehicle or a child. We run new low-voltage wiring, add surge protection, and verify the safety edges and photo eyes before the gate goes back into service. Call (877) 610-2993 with your gate’s symptoms and we’ll quote the whole job.
What does gate access control cost in Augusta compared to Wichita?
Parts and hardware run about the same, and since we don’t add a trip charge inside Butler County, the total often lands lower than a Wichita shop that adds mileage. A keypad replacement in Augusta runs $180 to $450, same as our Wichita-area work. We price the job, not the ZIP code.
Gate Parts & Welding in Augusta
Most gate part replacements in Augusta run $120 to $350, and custom welding projects typically fall between $200 and $900. We can usually reach your property within 24 to 48 hours, because we stock common parts on the truck rather than ordering them in. Hal and his crew weld on site, in your driveway, so the gate never leaves your property. For the full list of what we replace and weld, see our Gate Parts & Welding page.
Hinge Replacement
Hinges take the most punishment of any gate component in Augusta, where the wind leans against the gate frame hour after hour. A typical hinge replacement here runs $95 to $210 per hinge, depending on whether it’s a light ornamental barrel hinge or a heavy weld-on pin hinge for a pipe gate. On the ranchette properties south and east of town, ball-and-socket hinges sit in ground-level moisture traps created by the clay soil, and they corrode faster than nearly any other hardware type.
Post Replacement
Augusta’s freeze-thaw cycles act on Butler County clay in a slow annual rhythm. The soil swells with winter moisture, then contracts in summer, and over a decade or two that movement heaves posts and cracks their concrete footings. When we replace a post in Augusta, we dig 24 to 30 inches deep, pour a new footing, and re-plumb the post so the gate hangs true. Post replacement runs $180 to $420 per post.
Custom Welding
Some jobs don’t fit a catalog part number, and that’s where on-site welding changes the conversation. Broken gate frames, custom brackets, ornamental features that need re-attaching: Hal’s crew welds it in your driveway. Custom welding projects in Augusta generally run $150 to $450 for most residential jobs, more for extended structural repairs on large pipe gates. If a weld cracks or a hinge loosens within 90 days, the Done Right Promise brings us back to make it right.
How quickly can you get to Augusta for a gate parts or welding job?
Most part replacements and welding jobs in Augusta are scheduled within 24 to 48 hours of your call. If the gate is stuck open or won’t close and you have livestock or a security concern, we treat it as urgent and move you up. Call (877) 610-2993 and tell us what’s happening; we’ll give you an honest arrival window.
Do you offer emergency gate service in Augusta?
Yes, and we answer the phone 24/7, so you won’t wait on a call back. If your gate has fallen off its hinges, is blocking a driveway, or won’t close to keep livestock in, that’s urgent and we prioritize it. Describe the failure when you call (877) 610-2993, and we’ll make a plan on the spot.
Brands We Service in Augusta
We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Common boards, remotes, and safety eyes for the brands we see most in Augusta ride on the truck. See our brands page for the full breakdown.
Pricing for Gate Repair in Augusta, KS
| Service | Typical range in Augusta |
|---|---|
| Hinge replacement | $95-$210 per hinge |
| Gate realignment | $125-$300 |
| Hinge or post repair | $150-$400 |
| Post replacement with new footing | $180-$420 per post |
| Motor repair | $180-$340 |
| Electric gate repair | $225-$550 |
| Automatic opener repair (heavy pipe gates) | $325-$650 |
| Keypad replacement or reprogramming | $180-$450 |
| Phone entry installation | $600-$1,400 |
| Basic single swing driveway gate install | $900-$1,800 |
| Sliding gate installation | $1,800-$4,500 |
What pushes a price up in Augusta is usually the post. A gate hinge fails because the post moved, and the post moved because the clay soil heaved it. Fixing the post properly costs more than adjusting the hinge, but it’s the only fix that lasts. Every job is quoted and agreed before work starts, and every invoice carries the 90-Day Done Right Promise in writing.
Neighborhoods We Serve in Augusta
We work throughout Augusta and the surrounding acreage belt, and we answer calls around the clock. Most repairs start within a day or two, and urgent calls get priority.
- Older in-town neighborhoods near State Street
- East 7th and Dearborn residential blocks
- Newer infill subdivisions off Kelly Road
- Acreage lots along SW Ohio and SE 100th
- Rural-residential lots south and east of the city limits
Service Area - Cities Near Augusta
We work throughout Butler County and the surrounding area. In addition to Augusta, KS, our crews regularly serve Andover, KS, El Dorado, KS, Derby, KS, Wichita, KS, and Park City, KS. Dispatch and scheduling are coordinated from our Wichita office; crews serve Augusta locally.
Serving Augusta, KS - Our Local Coverage Area
Gatewood Fence & Gate crews serve Augusta and the communities around it; dispatch is coordinated from our Wichita office. The map shows the Augusta coverage area; if your address is on it, we can help.
Also serving nearby: Augusta, KS, Andover, KS, El Dorado, KS, Derby, KS, Wichita, KS, Park City, KS.
FAQs About Gate Repair in Augusta
Most Augusta repairs start within a day or two of your call. Urgent cases, like a gate stuck open with livestock or a gate blocking a driveway, get priority. Call (877) 610-2993 and a live person answers any hour, day or night.
Most hinge, post, and realignment repairs don’t require a permit in Augusta. New gate installations sometimes do, depending on the location and whether new power is being run to the gate. We’ll check the local requirements before we start and tell you exactly what’s needed.
Wind-driven hinge wear and post heave from the clay soil. The sustained 20 to 30 mph south and southwest winds push gate frames out of square, and the freeze-thaw cycle works posts out of plumb. We re-plumb posts and repair footings on most Augusta service calls. Start with the post, and the gate stays fixed.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Augusta Customers Say
"Beautiful gate and solid work. The build took about three weeks longer than the estimate because he was waiting on the ironwork, and I would rather have known that at the start than found out along the way."
- Beatrice Nwosu"Operator had died and the manufacturer no longer makes the board. Rather than sell me a whole new system he found a compatible unit and adapted the mount. Saved me a great deal of money."
- Salvador Arredondo"Hundred and forty feet of cedar privacy fence, all posts set in concrete, all of it dead level on ground that is anything but. He walked the line with me twice before a single hole was dug."
- Judith Stallworth