Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Augusta
Gate parts and welding in Augusta usually comes down to one of two jobs: a decorative driveway gate that’s sagging in town, or a wide steel pipe gate on a ranchette that’s seized up and won’t swing. We handle both, and we fix them at your property instead of hauling the gate off to some shop across the county. Hal Gatewood has been running Gatewood Fence & Gate since 2001, and our crew knows the difference between repairing a hinge on a 1970s ranch home’s gate and re-welding a 16-foot pipe gate on a county road south of Augusta. Call (877) 610-2993 and a live person answers, day or night.
Why Gatewood Fence & Gate Is Augusta’s Preferred Gate Parts & Welding Company
We’ve worked on enough gates in Augusta to know what holds up and what doesn’t. The housing stock here spans early oil-boom construction from the 1910s through mid-century ranches and newer infill, which means the gate posts we encounter are often wrapped in decades-old concrete that’s crumbling. That’s not the kind of problem you solve by swapping a hinge and hoping. We re-plumb posts, cut out bad footings, and weld new hardware so the repair lasts.
Augusta customers call us because we show up in the window we promise, and because our name is on the shop. Every job carries the 90-Day Done Right Promise in writing, not as a verbal pat on the back. If something isn’t right, one call brings us back, and we fix it. No runaround.
We also answer the phone around the clock. Not a voicemail to leave a message on, not a call center three states away. When you call (877) 610-2993, you talk to a real person who knows gates.
Our Gate Parts & Welding Services in Augusta
Hinge Replacement
Hinge replacement in Augusta’s rural areas is its own specialty. On the ranchette and acreage lots south and east of town, large-span steel pipe gates sit on ball-and-socket hinges that collect clay-soil moisture. Those hinges corrode from the inside out and seize even when the gate looks clean. We cut the old hinge off, weld a new one onto the existing pipe, and re-hang the gate with proper swing clearance. In town, we replace worn ornamental hinges and rebuild the mounting points so the gate doesn’t sag within a year.
Post Replacement
Butler County’s freeze-thaw cycles heave clay soil against gate posts every winter. The concrete footings crack, the post tilts, and the gate starts dragging or missing the latch. We remove the old post and footing, pour a new base, set the post plumb, and weld or bolt the gate back into alignment. We recently rebuilt a 16-foot steel pipe swing gate on a county road off SW 120th Street where the ball-and-socket hinge post had seized solid from years of clay-soil moisture. Our crew cut out the old footing, poured a new concrete base, welded fresh hinges, and re-hung the gate with restored swing clearance, plus added a solar gate opener because the acreage has no mains power at the entrance. That’s the kind of job we do regularly around Augusta.
Rail Repair
Steel pipe gates sag from wind load and their own weight. The top rail bends, the latch side drops, and suddenly the gate won’t close. We straighten or replace rails, reinforce the corners with welded gussets where they’re needed, and correct the hinge alignment. On wide spans, we add mid-rail support so the gate doesn’t rack under Butler County’s sustained 20 to 30 mph south winds.
Custom Welding
Some Augusta gates need more than a patch. If a post has rusted through at ground level, we weld a new stub section onto the existing steel instead of replacing the entire post. If a hinge mount is torn, we grind, reinforce, and weld it back stronger than it was. We do all of it on site, in your driveway or at the pasture entrance, so you’re not left without a gate while a shop works on it across town.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Augusta
For automated gates around Augusta, we service Viking, Ghost Controls, and DoorKing equipment, which covers most of the openers on acreage entrances we see. We keep common parts stocked and can get anything else fast. The welding and mechanical work fixes the gate itself; the opener service keeps it opening. When we repair one, we check the other, because a gate that’s binding will burn out a good opener in a season.
Common Gate Parts & Welding Problems We See in Augusta Homes
- Seized ball-and-socket hinges on rural pipe gates. Clay-soil moisture sits at the hinge base year-round, corroding the joint until the gate won’t move. This is the single most common rural gate failure south and east of town.
- Wind-driven sag on wide swing gates. Sustained south and southwest winds rock the gate against the hinge post, shifting it gradually until the latch misses by an inch and the gate won’t close.
- Frost-heaved hinge posts. The clay soil under Augusta freezes and expands each winter, tilting posts and cracking old concrete. The gate binds or drags, and the post needs re-setting.
- Torn hinge mounts on older ornamental gates. Decades-old in-town gates often have thin steel mounts that fatigue and tear under repeated wind load. We weld reinforcement plates and rebuild the mount.
Pricing for Gate Parts & Welding in Augusta, KS
Every job gets a written price before we start, and that’s the price you pay. A typical hinge replacement on an ornamental driveway gate in Augusta runs $160 to $320 installed. Steel pipe gate hinge replacement on acreage, including welding and alignment, usually lands between $280 and $480 depending on span and condition. Post replacement with new concrete footing runs $350 to $750 for most residential gates. Custom welding repair work falls between $180 and $600 depending on the extent of the damage. Rail repair and straightening typically runs $150 to $400. We offer $40 off any repair over $200, no trip charge inside Butler County, and a free second opinion on any written estimate you’ve received elsewhere.
We Also Serve Cities Near Augusta
Our Gate Parts & Welding crew covers Augusta and the surrounding communities, including Andover, El Dorado, Derby, and Wichita. If you’re in the area and your gate is sagging, seized, or torn at the hinge, call us. This is what we do every day. For the full picture of our work in this part of the county, see Gate Parts & Welding in Augusta.
Serving Augusta, KS - Our Local Coverage Area
We’re based in the Augusta area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Augusta
The hinges on those gates sit inside ground-level pockets formed by Butler County’s clay soil. Moisture collects there and corrodes the hinge from the inside, seizing the joint even when the outside looks fine. Severe cases require cutting the old hinge off, welding on a new one, and sealing the joint area so water drains away. If your gate is getting hard to swing, call (877) 610-2993 before the hinge snaps.
Yes, and that’s usually the right fix. We grind off the old hinge, weld a new one to the existing pipe, and re-hang the gate with fresh alignment. The gate stays in your driveway the whole time. Replacing the entire gate is only necessary when the pipe itself is rusted through or structurally compromised.
In almost every case we see around Augusta, it’s the gate frame and hinges sagging, not the opener. A 20-foot gate carries a lot of wind load, and after enough south wind, the hinge post shifts and the frame racks. The opener then works harder and eventually fails. We straighten and reinforce the gate, correct the hinges, and re-align the opener’s travel. Fix the gate first or you’ll replace the opener next.
Yes. Solar powered gates need the same safety equipment as wired ones. Photocells prevent the gate from closing on a person, animal, or vehicle, and they’re required for any automatic operator. We install and align them as part of any gate automation repair or new install, including solar systems on rural acreage entrances.
We set hinge posts in new concrete footings that extend below the freeze line, and we use galvanized or heavier-gauge steel posts sized for the gate span. On clay soil, we also make sure water drains away from the base so the post isn’t sitting in a moisture trap. Call (877) 610-2993 for a free estimate on post replacement around Augusta.
Call Gatewood Fence & Gate for Gate Parts & Welding in Augusta
If your gate is sagging, seized, or torn at the hinge, call us. We repair gates in Augusta the right way, on site, with the price agreed before any work starts. Hal Gatewood’s name is on the shop and on every invoice. That’s the oldest accountability there is. Call (877) 610-2993 for a free estimate, or flag us down if you see the truck. We’re around.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Augusta and the surrounding Butler County communities since 2001.