Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Motor & Opener Across Beverly Hills
When a gate motor fails in Beverly Hills, it’s rarely a simple swap. The homes here, particularly in the hills north of Sunset, run on custom-fabricated gates and operators that were built to fit a specific driveway, a specific grade, and a specific era of metalwork. A malfunction often traces back to a worn hinge post, a corroded control board from marine-layer moisture, or a slope compensation issue that a flat-lot technician would misdiagnose as a dead motor. We’re Gatewood Fence & Gate, owned by Hal Gatewood since 2001, and we fix what others want to replace. Call us at (877) 610-2993 and you’ll get Hal or a member of his crew, not a voicemail maze.
Why Gatewood Fence & Gate Is Beverly Hills’s Preferred Gate Motor & Opener Company
Hal Gatewood put his name on the shop in 2001 and never took it off. When you call about a Gate Motor & Opener issue in Beverly Hills, you reach a person who knows the difference between a 90210 hillside estate gate and a 90211 flats swing gate. The calls we get from Beverly Hills tend to start the same way: someone’s estate manager says the gate stopped halfway, or a homeowner notices the motor groaning but not moving. We arrive, diagnose the actual cause, and tell you straight whether it’s a repair or a replacement. No pressure, no upsell.
Beverly Hills customers keep our number because we show up when we say we will. Dispatch is coordinated from our Los Angeles office, but the crew that arrives at your gate knows this area. They’ve seen 1920s Spanish Colonials south of Santa Monica Blvd and mid-century estates in the flats. They’ve also reset post footings on Coldwater Canyon driveways so steep the gate geometry shifts after a wet winter. Every job carries the 90-Day Done Right Promise in writing. If it’s not right, Hal comes back. One call, no runaround.
We’re certified to service major brands including Linear, Viking, Ghost Controls, and DoorKing. More importantly, we repair before we replace. Fix the panel without the post and you’ll fix it twice. That’s a Beverly Hills lesson, not a brochure line.
Our Gate Motor & Opener Services in Beverly Hills
Motor Repair
Most Beverly Hills motor failures we see are not the motor itself. A 1980s BFT swing operator that trips its limit switch halfway up a Coldwater Canyon driveway? The post has likely shifted and the grade compensation is off. We diagnose the actual fault, weld on site if brackets or hinge points are involved, and recalibrate rather than condemning a good motor. Repairs run $225 to $440 on average. If the motor is genuinely burned out, we say so plainly and quote a replacement before any work begins.
Motor Installation
When an older operator on a Beverly Hills estate is beyond reasonable repair, we install a new motor matched to the existing gate’s weight, length, and slope. That’s not a generic conversation. A grand 1930s wrought-iron swing gate in 90210 needs a different operator than a modern steel slide gate on a flat lot in 90212. Full motor installation in Beverly Hills typically runs $1,400 to $2,800 depending on gate size, power availability, and whether new safety edges or photocells are required. We quote the exact price before ordering anything.
Linear Motor
Linear arm operators are common on Beverly Hills estate gates, often paired with Video Intercoms and estate security systems. When a Linear motor arm wears or a control board corrodes from marine-layer moisture, the usual symptom is a gate that starts, stutters, and stops. We service and replace linear motors for homes throughout 90210, 90213, and the flats. Linear motor replacement in Beverly Hills runs $900 to $1,600, parts included for common models.
Slide Motor
Slide gates on smaller Beverly Hills lots, especially south of Santa Monica Blvd in 90211 and 90212, collect grit from Santa Ana winds in roller tracks and rack-and-pinion gears. The motor works harder than it should, and eventually the overload circuit trips. We clean, realign, and replace slide motors as needed. A slide motor replacement for a typical Beverly Hills driveway gate runs $850 to $1,500. The diagnosis is free when you book a repair.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Beverly Hills
Hal’s crew is certified on nine major gate operator brands, and in Beverly Hills we most often see Linear on modern installs, Viking on long slide gates, Ghost Controls on retrofits, and DoorKing on daily-use residential gates. We stock boards, gears, and safety edges for these brands so we’re not waiting a week on a distributor. If your operator is a Ghost Controls or a Linear and the board is still manufactured, we can typically replace it same week. If it’s obsolete, we’ll tell you what your retrofit options actually cost instead of stringing the repair along.
For a full look at what we handle beyond this page, see our Gate Motor & Opener service hub.
Common Gate Motor & Opener Problems We See in Beverly Hills Homes
- Worn hinge posts and sagging gates on hillside estates. A gate sags in the hinge post, not in the middle. On sloped 90210 driveways, a shifted post throws off grade compensation and the gate drags, often misdiagnosed as a bad motor. We reset the post, not just the board.
- Obsolete control boards on 1980s-era BFT and FAAC operators. Marine-layer moisture from being 5 to 6 miles inland corrodes boards on north hills estates. When the manufacturer stopped producing them, only a retrofit or full replacement fixes it. We give you both numbers.
- Debris in slide gate tracks after Santa Ana winds. South-of-Santa-Monica lots see grit and palm debris driven into rollers and rack-and-pinion gears. The gate jams, the overload trips, and an absent owner hears about it from their estate manager. We clean, realign, and advise whether a gear replacement is overdue.
- Safety sensor failures on original wrought-iron gates. Many 1920s through 1960s Beverly Hills gates predate modern UL 325 entrapment protections. A missing or failed photocell is a genuine safety hazard, especially with small children and pets. We retrofit edge sensors and photocells that meet current standards without altering the historic ironwork.
Pricing for Gate Motor & Opener in Beverly Hills, CA
Here are honest numbers for the Beverly Hills market. Motor repair typically lands between $225 and $440. Motor installation runs $1,400 to $2,800 depending on gate weight, driveway slope, and whether new safety edges are needed. Linear motor replacement averages $900 to $1,600. Slide motor jobs run $850 to $1,500. Battery backup installation adds roughly $500 to $800. Those are full parts-and-labor figures, not labor-only bait. The price we quote is the price you pay, agreed before any work starts. We also honor $40 off any repair over $200, a free second opinion on any written estimate, no trip charge inside the county, and a permanent 10% discount for seniors and veterans. Call (877) 610-2993 for a written quote.
We Also Serve Cities Near Beverly Hills
While this page covers Gate Motor & Opener in Beverly Hills, Hal’s crew also works in Century City, West Hollywood, Culver City, and Hollywood. Beverly Hills customers get the same live-answer phone line and the same 90-Day Done Right Promise as everyone else. The drive is short; the standard doesn’t change.
Serving Beverly Hills, CA - Our Local Coverage Area
We’re based in the Beverly Hills area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Motor & Opener in Beverly Hills
Probably not. On sloped Beverly Hills driveways, a halfway stop is usually a grade-compensation problem, not a dead motor. A post has shifted, the gate drags, and the limit switch shuts the operator down to protect itself. We reset the post and recalibrate the slope parameters for $225 to $440 in most cases. If the motor itself is failed after we test it, we’ll tell you and quote replacement. Call (877) 610-2993 to have it checked.
Yes. We fit current UL 325-compliant photocells and edge sensors to historic Beverly Hills ironwork all the time, without changing the look of the gate. The retrofit typically runs $300 to $600. It’s worth doing on any original gate that predates modern entrapment protections, and it’s a standard part of our Motor Repair work on older estates.
Santa Ana winds drive grit, palm debris, and fine dust into the roller track and rack-and-pinion gear. The gate binds, the motor’s overload trips, and the gate stops moving. We clean the track, realign the rollers, and inspect the gear teeth for wear. Typical service call in 90211 or 90212 runs $200 to $350. If the gear is worn beyond tolerance, replacement is usually $300 to $500 more.
We’ll try the retrofit first. For many 1990s Linear and BFT control boards, a modern aftermarket board or retrofit kit exists and costs $400 to $800 installed. When no compatible retrofit is available, a full linear motor replacement in Beverly Hills runs $900 to $1,600. We give you both numbers and let you decide. No pressure, no manufactured urgency.
That’s a normal day in Beverly Hills. We coordinate directly with estate managers, private security staff, or household staff as needed. Our crew is background-checked and uniformed, and we document the work so the homeowner can see exactly what was done and why. The 90-Day Done Right Promise applies no matter who we worked with on site. Call (877) 610-2993 and we’ll get the gate sorted.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Beverly Hills since 2001.
Get a free estimate for Gate Motor & Opener repair or installation in Beverly Hills. Call (877) 610-2993 and you’ll speak with a real person who knows this work. We show up, quote fairly, and fix it right.