Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in La Vergne, TN
Gate repair in La Vergne typically costs $145-$390 for most residential calls, and we’re usually on site within 60-90 minutes for emergencies. If your gate is binding, stalling, or refusing to open, call (877) 610-2993. A live person answers day or night, and we’ll tell you straight what we can do and what it will cost before we roll the truck.
La Vergne sits at a unique crossroads. It’s one of Tennessee’s most warehouse-dense cities, with distribution campuses lining I-24 along Waldron Road and Industrial Boulevard running slide gates and barrier arms on near-continuous truck traffic. At the same time, the residential subdivisions built during the 1995 to 2008 boom are now watching their 15-to-25-year-old HOA entrance gates fail in waves. That dual workload, commercial and residential, shapes every repair we make here.
Why La Vergne Homes Are Different
Middle Tennessee ice storms crack control boxes and push moisture into electrical connections. Then humid summer arrives and rust starts working on the steel frame. Over time, Rutherford County’s expansive clay soil expands and contracts with every wet spring and dry August, and that movement slowly rocks gate posts out of plumb. You see the result one morning: the gate binds, the opener strains, and a roller or hinge that was quietly wearing for six months finally gives out.
This is the pattern we see all over La Vergne, from Lake Forest and Autumn Ridge to the commercial corridors along Waldron Road and Industrial Boulevard. The distribution parks run vehicle gates on 24/7 duty cycles for truck traffic, burning through operators in a fraction of the typical residential lifespan. Meanwhile, the tract subdivisions built between 1995 and 2008, many governed by HOAs with gated entrances, are hitting active failure cycles on their original swing and slide operators. The circuit boards, chains, and limit switches from that era are dying at scale. Newer apartment and townhome complexes along Murfreesboro Road and Jefferson Pike add multi-tenant vehicular gate work to the mix. We start at the post and the hinges instead of slapping a new opener on a gate that was never going to run smooth regardless.
Gate Repair in La Vergne
Gate repair in La Vergne splits into two tracks. The warehouse and distribution parks off Waldron Road and Industrial Boulevard keep commercial slide gates and barrier arms running near nonstop, and the subdivisions built during the 1995 to 2008 boom are now seeing 15-to-25-year-old HOA entrance gates fail. When a gate binds, stalls, or refuses to open, you need someone who will answer the phone and show up. We do both. Our Gate Repair work covers everything from residential swing gates in Lake Forest to high-cycle commercial slides at distribution centers.
Electric Gate Repair
Most electric gate failures in La Vergne trace back to the operator, the loop detector, or the safety photocells. Along Waldron Road and Industrial Boulevard, where truck gates run near-continuous 24/7 duty cycles, we see operators burning out in a fraction of a typical residential lifespan. On the residential side, the aging HOA entrance gates across the 37086 and 37089 zip codes are hitting a wave of circuit board and limit switch failures. We service and repair electric gate systems from Linear, Viking, Ghost Controls, and DoorKing. Electric operator board or limit switch replacement typically runs $260-$650.
Hinge & Post Repair
Rutherford County sits on expansive clay. It swells when it’s wet, shrinks when it’s dry, and over a few seasons that movement rocks gate posts out of plumb. In La Vergne, where the humidity swings are dramatic, we see hinge posts leaning just enough to make a swing gate sag and drag, or a slide gate bind on its track. Fix the panel without the post and you’ll fix it twice. We re-set posts, weld hinge reinforcement back to the frame, and repair the gate where it’s mounted. Hinge and post repair typically runs $145-$340.
Gate Realignment
A gate that scrapes the ground, leaves a gap at the latch, or has to be shimmed to stay closed is out of alignment. In La Vergne’s tighter lots and shared driveway setups, this happens more often because the gate gets used harder and the posts have less soil to hold them. We realign the frame, reset the hinges, and make sure the gate closes square on the stop. Gate realignment typically runs $125-$275.
Why do slide gates on Waldron Road and Industrial Boulevard need repair so much more often than residential gates in La Vergne?
They run near-continuous 24/7 duty cycles for truck traffic, which means they accumulate in a single year the same wear a residential gate sees in two decades. Rack and pinion gears strip, operators burn out, and loop detectors that get rattled by constant truck vibration drift out of calibration. When a logistics yard gate locks up mid-shift, we treat it as a same-day emergency. Call (877) 610-2993 and we’ll get there fast.
Is there a local reason gate posts shift so much in La Vergne?
Yes: Rutherford County’s expansive clay soil. It swells during wet seasons and shrinks during dry stretches, and every cycle rocks gate posts a little further out of plumb. Over a few years that movement binds slide gates on their tracks and makes swing gates sag on their hinge posts. It’s the single most common root cause we find in La Vergne, and it’s why we re-set posts rather than just patching symptoms. Call (877) 610-2993 for a free estimate.
Gate Installation in La Vergne
Gate installation in La Vergne runs $1,800 to $6,500 for most residential driveway gates, and $3,500 to $12,000+ for commercial slide gates and barrier arms at the distribution parks off Waldron Road and Industrial Boulevard. The price gets quoted and agreed before any work starts, so there’s no surprise at the door. If you’re pricing a gate in 37086 or 37089, call (877) 610-2993 and we’ll give you a real number, not a range that balloons later. Our Gate Installation work is measured, ordered, and scheduled, never rushed.
Driveway Gate
A driveway gate in La Vergne has to hold up to clay soil and Tennessee humidity. Rutherford County’s expansive clay shifts with the seasons, and that movement works on gate posts month after month. We set posts deeper and brace them right so the gate doesn’t start binding by its second winter. Most residential driveway gate installs here run $2,200 to $5,800 with an operator, depending on the gate size and whether we’re adding a slide or swing mechanism.
Sliding Gate
This is the gate type we install most in La Vergne commercial work. A slide gate doesn’t need the big arc of clear space a swing gate demands, and at a distribution yard off Waldron Road, that arc usually doesn’t exist. Trucks pull right up to the dock. A slide gate rides on a track and roller system, and we build that system to take the cycle count a La Vergne warehouse throws at it. Commercial slide gate installs here typically run $4,500 to $12,000, including operators rated for continuous duty.
Swing Gate
Swing gates still make sense on bigger residential lots and HOA entrances where there’s room for the leaf to travel. In La Vergne’s 1995 to 2008 subdivisions, we’re often replacing swing gates that were installed with the original HOA build. The gate itself might still be salvageable, but the operator, hinges, and post bases are shot. We’ll tell you honestly whether to replace the gate, the operator, or both. Residential swing gate installs run $1,800 to $6,000 here depending on steel, automation, and the post work involved.
Do I need a swing gate or a slide gate for my La Vergne commercial yard?
If your yard off Waldron Road or Industrial Boulevard has trucks pulling tight to the dock, you need a slide gate. A swing gate needs a full arc of clear space to open, and in most La Vergne distribution yards that arc doesn’t exist between the dock, the retention wall, and the truck apron. A slide gate runs parallel to the fence line on rollers and needs far less room. We’ll measure your site and tell you which makes sense. Call (877) 610-2993 for a free measure and written price.
Can you install a gate operator on an existing La Vergne HOA entrance gate without replacing the whole gate?
Yes, and we do it regularly. If the steel is sound and the hinges or rollers are still serviceable, we can retrofit a new Linear or DoorKing operator onto the existing gate and keep the structure in place. That’s the repair-first approach that saves HOAs real money. If the gate itself is beyond saving, we’ll tell you that straight. Most retrofits on La Vergne HOA gates run $1,200 to $4,000. Call (877) 610-2993 for an exact quote.
Gate Motor & Opener in La Vergne
A failed gate motor in La Vergne usually means one of two things: a distribution yard off Waldron Road is locked shut during a shipping window, or an HOA entrance gate in a 25-year-old subdivision is stuck mid-swing with residents queued behind it. Both are urgent. Gatewood Fence & Gate answers the phone with a live person 24 hours a day, and Hal Gatewood has been fixing gate motors and openers since 2001. Our Gate Motor & Opener service covers repair, replacement, and retrofit across every brand we carry.
Motor Repair
Most gate motor repair calls in La Vergne start with the operator going dead or the gate stalling mid-cycle. We got a call at 6:40 a.m. from a distribution center off Industrial Boulevard when their slide gate operator refused to open for the first outbound truck. The gate was a high-cycle Viking slide motor that had burned through its control board after months of relentless 24/7 use. We swapped the board onsite and replaced a worn rack-and-pinion section so the next shift wouldn’t strand another trailer. Typical gate motor repair in La Vergne runs $180 to $450, depending on what failed.
Linear Motor
Linear gate motors are common across La Vergne’s apartment and townhome complexes along Murfreesboro Road and Jefferson Pike, where multi-tenant vehicle gates get heavy daily cycling. The weak points we see most often are failed capacitor packs, burned contactors, and limit switches that drift out of adjustment, which makes the gate stop short or over-travel and bind. We service and repair Linear operators on site, and we keep common Linear parts stocked for La Vergne calls. Replacing a contactor should not mean replacing the whole operator. A replacement control board on a legacy operator usually falls between $250 and $400 with labor.
Slide Motor
Slide motors take the most abuse in La Vergne because the warehouse gates along Waldron Road and Industrial Boulevard use them relentlessly for truck traffic. A slide motor running 24/7 wears gears, strips rack sections, and overheats windings far faster than a residential swing motor that cycles a few dozen times a day. We handle slide motor repair, gear replacement, rack alignment, and full slide motor replacement when the unit is beyond saving. A full new slide motor for a warehouse gate off Waldron Road typically runs $1,400 to $2,800 installed, while a residential swing motor replacement runs $900 to $1,800.
How fast can you get to a La Vergne distribution center off Waldron Road when a slide gate motor fails during a shipping window?
On commercial gate failures in La Vergne we aim for same-day response, and the warehouse calls we get off Waldron Road and Industrial Boulevard are treated as emergencies. A locked yard during a shipping window costs you money by the minute, so we keep slide motor control boards, limit switches, and replacement gears stocked locally. The phone is answered by a live person 24/7. Call (877) 610-2993 when it happens.
My HOA entrance gate in a La Vergne subdivision built around 2000 uses an operator with an obsolete control board. Can you retrofit it, or do we need a full replacement?
In most cases, a 15-to-25-year-old gate operator with a burned control board can be retrofitted with a modern compatible board for $250 to $400 installed, which is far less than the $1,400 to $2,800 a new slide motor or the $900 to $1,800 a new swing motor would cost. The honest answer depends on what else is worn. If the motor windings are also failing or the gearbox is grinding, we’ll tell you that straight. Call (877) 610-2993 for a free second opinion.
Gate Access Control in La Vergne
Gate access control work in La Vergne splits into two very different worlds. The distribution parks off Waldron Road and Industrial Boulevard run vehicle gates on near-continuous duty cycles for truck traffic, and when one fails, a shipping yard locks shut. The other side is residential: HOA entrance gates built in the late 1990s and early 2000s, now 15 to 25 years old, with control boards and keypads that are starting to fail all at once. We repair both. Our Gate Access Control service covers keypads, card readers, phone entry, remote controls, and full system upgrades.
Keypad Entry
Keypads on La Vergne HOA gates and apartment complexes take direct weather exposure, and after a few Middle Tennessee ice storms the rubber membrane cracks and moisture creeps into the board. We replace keypads, rewire them into existing operators, and program codes on site. If your keypad works intermittently after rain, that’s usually corrosion on the terminal strip, not a dead keypad. A keypad replacement or card reader install in La Vergne typically runs $220 to $480 depending on the system and the amount of rewiring.
Card Reader
Distribution centers and multi-tenant apartment gates along Murfreesboro Road and Jefferson Pike rely on card readers that get hammered by truck drivers and delivery traffic. We install Wiegand and proximity readers, tie them into existing access panels, and troubleshoot readers that deny valid cards because a ground wire worked loose. For commercial yards, we can add anti-passback so a card can’t be used twice in a row to let a second vehicle through. Replacing a photocell pair runs $90 to $180.
Phone Entry
Many La Vergne subdivisions are still running 20-year-old phone entry systems that dial landlines nobody answers anymore. We retrofit those onto cellular-based systems, often keeping the original keypad housing and pedestal. You don’t need to replace the whole entry station to upgrade the phone feature. We’ve done this on older HOA gates throughout the 37086 and 37089 zip codes. A full phone entry retrofit onto an existing pedestal runs $500 to $900.
My HOA gate in La Vergne’s older subdivisions won’t close fully at night-what’s the most likely cause?
The most likely cause is a misaligned safety photocell on a late-1990s swing operator, which makes the gate reverse before it seats fully in the closed position. The beam gets knocked out of alignment when the post shifts or when a delivery truck clips the pedestal. We fix that in one visit. Call (877) 610-2993 and we’ll schedule a time to look.
After an ice storm, our gate access keypad on Murfreesboro Road stopped working-should we replace it?
Not necessarily. Ice storm failures on keypads are often water intrusion that shorted the terminal strip or froze the membrane, not a full board failure. We dry out the housing, check continuity, and replace the keypad only if the board is actually gone. A new keypad is cheaper than a new operator, and we’ll tell you which one you need. Call (877) 610-2993 for a straight answer.
Gate Parts & Welding in La Vergne
When a gate binds, a hinge tears loose, or a post drifts out of plumb in La Vergne, you need a crew that understands tight sites: shared driveways, rights of way, sliding gates where a swing gate will not fit, and vehicle access that has to keep working while we are in the middle of the repair. La Vergne’s warehouse-dense I-24 corridor along Waldron Road and Industrial Boulevard runs distribution center slide gates on near-continuous 24/7 truck duty cycles, so parts wear fast and downtime costs real money. We bring the welder to the gate, not the other way around. Our Gate Parts & Welding work keeps gates running in place.
Post Replacement
A gate sags in the hinge post, not in the middle, and that is where we start. Rutherford County’s expansive clay soils shift seasonally with moisture, gradually rocking gate posts out of plumb. That is why so many La Vergne swing gates bind on the latch side or stall halfway through their arc. Our post replacement work involves excavating the old footing, setting the new post plumb in fresh concrete, and welding the hinge brackets back at the correct height. A standard residential post replacement in La Vergne runs $450 to $800.
Rail Repair
Slide gate failures in La Vergne frequently trace back to the rail. High-cycle slide gates at logistics parks grind through rail surfaces and rack teeth from constant truck traffic. We cut out the damaged section and weld in a new one on site, which keeps the gate running while we work. On residential slide gates, rail repair often means correcting a grade shift from clay movement, then re-anchoring the rail to the new elevation. Typical La Vergne rail repair runs $350 to $850, rising for heavy commercial rail sections.
Custom Welding
Some repairs do not have a part number. When an HOA entrance gate has a decorative steel picket that rusted through at the base, or when a truck yard needs bracing added to a wind-damaged panel, we fabricate from stock steel. Custom welding in La Vergne often happens in tight spaces: shared driveways and rights of way where you cannot swing a gate, so the gate has to slide past a wall with fourteen inches of clearance. We have done it. Small custom welding repairs run $200 to $500; structural work runs $600 to $1,500.
Why do slide gates on Waldron Road wear out rollers faster than residential driveways in La Vergne?
A slide gate on Waldron Road can cycle forty or fifty times an hour during a shipping window, which is more cycles in a month than a residential driveway gate sees in a year. That constant truck traffic flattens rollers on one side, chews rack teeth, and overheats operators. We stock heavy-duty commercial rollers for high-cycle gates and replace them on site without shutting down the yard longer than necessary. Call (877) 610-2993 for an estimate.
Can you re-set a sagging gate post without replacing the whole gate in a tight La Vergne HOA side yard?
Yes, and that is most of what we do. We dig out the old footing, set the post plumb in fresh concrete, and weld the existing hinges and gate leaf back at the correct height. The gate itself usually does not need replacement. In tight side yards where there is not much working room, we hand-dig and set the post in stages so the gate can still close at night. Call (877) 610-2993 for a free estimate.
Brands We Service in La Vergne
We are certified to service nine major gate brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. We keep common parts in stock for Linear, Viking, Ghost Controls, and DoorKing systems, which means most La Vergne repairs don’t wait on shipping. If we don’t have it, we know where to get it fast. See all brands we service.
Pricing for Gate Repair in La Vergne, TN
| Service | Typical Range in La Vergne |
|---|---|
| Service call & diagnosis (no trip charge inside county) | $0-$95, credited toward repair |
| Hinge or roller replacement (residential swing gate) | $180-$340 |
| Hinge replacement (residential, per hinge) | $180-$420 |
| Gate realignment | $125-$275 |
| Electric operator board or limit switch replacement | $260-$650 |
| Loop detector replacement | $190-$400 |
| Gate motor repair (general) | $180-$450 |
| Residential swing motor replacement | $900-$1,800 |
| Commercial slide motor replacement | $1,400-$2,800 |
| Residential driveway gate installation (with operator) | $2,200-$5,800 |
| Commercial slide gate installation | $4,500-$12,000 |
| Full rack and pinion rebuild (commercial slide gate) | $600-$1,200 |
What pushes price up in La Vergne: post depth in expansive clay soil, commercial duty cycle demands, access constraints on tight lots, and the condition of existing electrical runs. The price you’re quoted is the price you pay. We don’t change it at the door. You get the number in writing before any work starts, and estimates are free.
Neighborhoods We Serve in La Vergne
We run calls all over town, from the residential streets near Lake Forest and Autumn Ridge to the commercial corridors along Waldron Road and Industrial Boulevard. Our typical response for gate repair calls inside the county is same day or next morning, and we don’t charge a trip fee inside the county for work over $200.
- Lake Forest
- Autumn Ridge
- Jefferson Pike corridor
- Commercial yards off Waldron Road and Industrial Boulevard
- Murfreesboro Road apartment and townhome complexes
Service Area - Cities Near La Vergne
We serve La Vergne directly, with dispatch and scheduling coordinated from our Memphis office and crews working locally in Rutherford County. If you’re just outside city limits, we also run regular calls to Smyrna, TN, Nolensville, TN, Brentwood, TN, Brentwood Estates, TN, and Mount Juliet, TN. Same live person on the phone, same upfront pricing, same 90-Day Done Right Promise.
Serving La Vergne, TN - Our Local Coverage Area
Gatewood Fence & Gate crews serve La Vergne and the communities around it; dispatch is coordinated from our Memphis office. The map shows the La Vergne coverage area; if your address is on it, we can help.
Also serving nearby: La Vergne, TN, Smyrna, TN, Nolensville, TN, Brentwood, TN, Brentwood Estates, TN, Mount Juliet, TN.
FAQs About Gate Repair in La Vergne
Yes. The subdivisions built between 1995 and 2008 across La Vergne are now watching their original gate operators fail in waves. We repair the operator, the post, the hinges, or all three, and we’ll tell you honestly whether a retrofit or full replacement is the better spend. Most HOA entrance gate repairs run $145-$390. Call (877) 610-2993 for a free estimate.
Rutherford County’s expansive clay soil swells when wet and shrinks when dry, rocking gate posts out of plumb over several seasons. In La Vergne, this is accelerated by the humidity swings and the tighter soil around posts in smaller residential lots. The fix is re-setting the post in deeper concrete, not just shimming the gate. We do this on site. Call (877) 610-2993 to schedule.
Call (877) 610-2993 any time. A live person answers 24/7, not a voicemail or call queue. We’ll ask what the gate is doing, give you a straight sense of whether it’s urgent or can wait, and book a window that works. Estimates are free, and there’s no trip charge inside the county for work over $200. Seniors and veterans receive a permanent 10% discount.
Ready to get your gate working right? Call (877) 610-2993 now. A live person will answer, day or night, and we’ll give you a free estimate with a price that won’t change at the door. Hal Gatewood stands behind every job with the 90-Day Done Right Promise, and his name is on the shop.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What La Vergne Customers Say
"Hundred and forty feet of cedar privacy fence, all posts set in concrete, all of it dead level on ground that is anything but. He walked the line with me twice before a single hole was dug."
- Judith Stallworth"Driveway gate had been dragging for two years and two other companies told me the whole thing needed replacing. Hal reset the posts, rehung it and it swings like it did when it went in. A fraction of the price of a new one."
- Hollis Amberly"He came out in the snow to get our gate closed after a delivery lorry clipped it, then came back in the spring to do the proper repair when the ground had thawed. Only charged for the second visit."
- Ingrid Solheim