Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Westmont
Gate repair in Westmont usually runs between $180 and $850 depending on what failed, and most hinge, track, and operator problems can be fixed the same day we show up. We work throughout the 90047 ZIP, from the blocks off South Vermont Avenue to the cul-de-sacs near Centinela, and we know what this neighborhood’s salt air and 80-year-old driveways do to gate hardware. Call (877) 610-2993 and you’ll get a live person, not a menu. Tell us what the gate is doing, and we’ll give you a straight answer about what it will take to fix it.
Why Gatewood Fence & Gate Is Westmont’s Preferred Gate Repair Company
Hal Gatewood has been fixing gates since 2001, and he still runs the shop himself. That means the person who answers the phone can actually tell you what to check before we even load a truck. Our crews know Westmont’s housing stock, the narrow concrete driveways, the old wrought iron, the gate operators that have been out in the weather since the first Bush administration. We are not a franchise. We are not working through a dispatch queue. We’re a local operation with a published address and a license number you can look up, and we’ve been doing this long enough that a lot of our Westmont work comes from neighbors recommending us to neighbors.
Every job we do carries the 90-Day Done Right Promise in writing. If something isn’t right, one call brings Hal back. No runaround, no fine print, no arguing about whether it was “covered.” That promise matters here because Westmont gates fail in ways that lazy repairs don’t fix, a rusty hinge pin gets replaced but the post underneath is rotted, the gate sags again in six months, and the guy who did the work is gone. We fix the post, the hinge, and the cause. Then we put it in writing.
Response time to Westmont is typically same-day for repairs, and emergency calls get answered around the clock. A live person picks up at 3 a.m. if that’s when your gate won’t close and you’ve got a family inside. We also keep common parts on our trucks, LiftMaster and FAAC control boards, hinge pins, gate wheels, track brackets, so we’re not driving back to the shop twice while your property sits open.
Our Gate Repair Services in Westmont
Electric Gate Repair
Westmont has a lot of electric gate operators installed 15 to 25 years ago, and the marine layer does not do them any favors. Moisture gets into the control board enclosure, corrosion builds on the terminal blocks, and the operator starts doing strange things, opening halfway, not responding, cycling on its own. We trace those problems to the board, the limit switches, or the power supply rather than guessing. Most electric gate repairs in Westmont run $220 to $480, and we quote the price before we start.
Automatic Gate Repair
An automatic gate is only as reliable as its weakest connection, a limit switch that’s out of adjustment, a photo eye that’s dirty, a receiver that’s lost its programming. We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, and we carry programming tools for all of them. If your remote stopped opening the gate or the gate starts and stops on its own, call us. We’ll find it without selling you a new operator you don’t need.
Hinge & Post Repair
In Westmont, hinge and post failures are the single most common gate repair we do, and they’re almost always a rust problem. The salt-laden air off the Pacific settles on the metal, works its way into the hinge barrel, and seizes the pin. Or worse, the post rots through right at the footing, and the weight of the gate slowly bends the post until the gate drags on the driveway. We replace hinge posts with a stainless steel core set in fresh concrete and swap in marine-grade stainless hinges. The gate gets plumb, square, and silent, and it stays that way. Typical hinge and post repair in Westmont runs $350 to $900 depending on whether the post is embedded in concrete or bolted to a wall.
Gate Realignment
Slide gates in Westmont go off-track because the driveway slab underneath them has moved. Decades of tree roots, thermal expansion, and settling crack and heave the concrete, and the gate wheels bind. We realign the track, shim or reset the rollers, and where the slab is too far gone, we cut and reset the track section so the gate runs true again. This is one of the most repeated calls we get in 90047, and it’s why we tell people not to just “adjust” a dragging gate. Fix the track, fix the wheels, and the gate runs for years.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Westmont
We’re certified to service nine major gate brands, and we keep repair parts locally stocked so Westmont customers aren’t waiting a week for a control board to ship. DoorKing operators are everywhere in this neighborhood, especially on old apartment and commercial gates, and we stock their common boards and loop detector parts. Linear and Viking show up on a lot of residential driveway gates from the early 2000s, and we still service them even though a lot of other companies will tell you to just replace the whole unit. If the operator can be fixed, we fix it. Our Gate Repair team has the programming tools and parts on the truck.
Common Gate Repair Problems We See in Westmont Homes
- Hinge posts rotting at the footing. Overnight marine layer deposits salt on the metal, and over 10 to 15 years the post corrodes through right where it meets the concrete. The gate starts to sag, then the lower hinge pin snaps. We replace the post with a stainless core and marine-grade hardware.
- Slide gates binding on cracked driveways. Mature ficus and magnolia trees throughout South LA send surface roots under the concrete apron that holds the bottom track. The slab lifts, the track kinks, and the gate wheels jam. We reset the track and shim the wheels to match the new slab height.
- Weld joints cracking from thermal cycling. Westmont summers push into the low-to-mid 90s, and repeated expansion and contraction work-harden the weld seams on older wrought iron gates. Hairline cracks open up under load, usually at the corners where the top rail meets the stile. We repair those welds on-site, and we actually weld, not just bolt a splice plate over the crack.
- Operator boards corroded by moisture. Salt-laden condensation creeps into the control box and eats the terminals and solder joints on the board. The gate starts acting erratically. We clean, repair, or replace the board and seal the enclosure properly so it doesn’t come back in a year.
Pricing for Gate Repair in Westmont, CA
A typical hinge and post repair in Westmont runs between $350 and $900. Electric gate operator repairs usually land between $220 and $480, and a full track reset on a slide gate that’s been lifted by tree roots typically costs $500 to $1,100. Weld and rust repair on a sagging wrought iron gate runs $180 to $650 depending on how many joints need work. The price you’re quoted is the price you pay, agreed before any work starts. No trip charge inside the county, and we offer $40 off any repair over $200, plus a free second opinion on any written estimate you’ve gotten. We’ll look at the other guy’s quote and tell you honestly whether the work he’s proposing actually needs doing. Call (877) 610-2993 for a free estimate.
We Also Serve Cities Near Westmont
Beyond Westmont, we regularly run calls to View Park-Windsor Hills, West Athens, Inglewood, and Lennox. Same crew, same 90-Day Done Right Promise, same live person on the phone. Gate Repair in Westmont covers this whole corner of South LA, and we know the streets well enough to find you without asking for directions twice.
Serving Westmont, CA - Our Local Coverage Area
We’re based in the Westmont area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Repair in Westmont
No, a basic repair like replacing a rusted post or swapping an operator with a like-for-like unit does not require a permit. But Westmont is unincorporated LA County, so if you’re adding a new automatic gate, moving an existing one, or changing the entrapment protection layout, the permitting path runs through LA County Building and Safety, not a city hall. Many outside contractors don’t know this and either skip the permit or waste a week filing with the wrong agency. We handle the County paperwork when a job needs it. Call (877) 610-2993 and we’ll tell you whether your repair falls under the permit threshold.
Because the hinge post has rusted through at the base, and the weight of the gate is bending the whole post assembly. The rust is often hidden below ground or inside the post sleeve, where you can’t see it until the gate drops. Once the post is compromised, the welds don’t matter, the geometry is wrong, and the gate will keep sagging until the post is replaced. We fix this with a stainless steel core set in new concrete and marine-grade hinges, the only repair that lasts on a Westmont property with salt exposure.
Yes, in most cases. We cut out the section of track that’s been lifted, reset it on a proper base, and shim the gate wheels to match the new slab height. Where the slab has heaved so badly that the track can’t be made level, we reset a new track section and anchor it to undisturbed concrete. Ficus and magnolia roots are a fact of life in Westmont, and this repair is one of our most common calls in the 90047 ZIP. The fix typically takes four to six hours and the gate runs true again.
Overnight moisture from the marine layer condenses inside the control enclosure, and because Westmont sits only 8 to 10 miles inland, that condensation carries salt. Over time the salt corrodes the terminal blocks and solder joints on the board, and the operator starts acting erratically. The board doesn’t have to look wet to be failing; the corrosion is microscopic. We repair or replace the board and then seal the enclosure properly, using weathertight gaskets and anti-corrosion terminal grease so the replacement board doesn’t fail the same way in two years.
Yes. Any automatic gate in unincorporated LA County must meet the current entrapment protection standards, photo eyes, reversing edges, and proper clutch or current-sensing settings. This isn’t optional, and an old gate from the 1990s likely doesn’t comply. We check entrapment protection on every automatic gate repair we do in Westmont, and if your gate can injure someone, we’ll tell you exactly what needs to be added or adjusted before we leave. We won’t sign off on a gate that can hurt a kid on a bike. Call (877) 610-2993 and we’ll walk you through what your gate needs.
If your gate is sagging, sticking, or won’t open, call us at (877) 610-2993. We’ll give you a straight price, show up when we say we will, and stand behind the work in writing. That’s how it should work, and it’s how we’ve done it since 2001.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Westmont and surrounding South LA communities since 2001.